Відео

So... What were your results?

Needs to have a radius on it to match the stock better.

last time i used mine i noticed the fences were not aligned to each other. one side was roughly 1/16" back from the other, looked like a jointer table. check that while your hunting for problems

Check the parts diagram but the hardware that holds the hub to the servo can slip. Unload the ATC and you have to pull the three fasteners that hold the tray to that hub but then there is another fastener that “tensions” the hub to secure it. Mine was slipping (secondhand 440) when I started to put mine through its paces and that seemed to fix my similar issue…

Tormach is cheap garbage, lots of unhappy customers

Wish I knew how to help, I can just like, share and comment and hope the youtube algorithm gets it to a person that does. All of the best man!

Bob, I had the exact problem with my 440. Unplug it. Take off the electronics cover and check every single screw lug that you can see. Mine had one intermittant connection with a loose screw. Tightened it and never had a problem since.

Sweet setup.

Try CLR or Seafoam to remove carbon

What you do I just ordered one

Will you be selling the coolant nozzle?

Same here, did you find a solution?

How does the butler creek ca with a hole in do for clarity? I removed the punch out on my photon RT at night and greatly helped with clarity. I am getting it warranted out for a 2-16 wraith HD. I don’t think it has a punch out on the front lens.

are both of the ram sticks the same? they are both 5600?

Mine was the same way. At each corner of the lid is a lip of plastic about 2 inches on each direction. I used a Dremel sanding drum to remove all 4 down to the level of the rest of the side. Dressed them up with 600 grit sandpaper and now the lid fits perfectly. So perfect it doesn't even vibrate while the printer is running. 10 minute job. Good luck.

I’ve had test of these scopes there crap

"Do not print directly on this surface" Hmmm

So the clogging problem is unsolved on currently selling snapmaker j1s printers? Unsolved for a year?

So this new version j1s is still that buggy and sold with old gen extruders that clog badly? Better buy the qidi x cf pro then.

same thing is happening to mine. i just bought it in november and its doing the same thing. did you ever figure it out?

Mine did the same at first. After printing PC with 60C chamber temp for a while it fit just fine

What was that multi tool you used to remove the pin?

Have you moved on to using the ultrasonic to clean the upper and lower?

How are you liking this unit so far? I'm looking at one of the smaller versions of this model. Appreciate the content and review.

Nice how much

Those X and Y prints are for your belt tension. Beautiful prints! I have been buying Snapmaker since the beginning and recently bought the Artisan beginning of the year. I am looking into buying this model as well.

Is that a ER32 collet? It seems there is more rigidity with the ER32 vs. ER20, since the holder has some mass to it. Haven't proved it but leaning towards this direction.

Would you say to take the QIDI or X1? x)

Sounds good.

The new system is working fantastic Bob. Did you get rid of the Red Truck?

Good day sir. I have 2 X-plus 2, having problems with overhangs drooping on my prints. I have used tree supports and regular supports with no luck. Any suggestion would be helpful. Thanks

Hello like to order a 6 jaw chuck

Where to buy one?

I had a firmware issues with my X-Plus 3. I found Qidi tech support to be very good. I hope they are for you!

I have seen mine literally blow of stringing with the circulation fan (the one on the right side), but those look to big to be the sort of stringing it could take off...

Hi Bob, there may be a problem with one of the two Y carriage. I currently have the same problem with an industrial printer with Hiwin linear guides. The noise is very similar, and it has been getting worse over the last few days. Now I can only move the carriage with a lot of force, and it keeps jamming during the movement. I will now replace the faulty carriage with a new one.

My xmax only lasted a few short days haha. Could tat be from when you take it off the bed? Id put a Webcam in

Are you using the hardened steel nozzle? This may be happening because you are not printing hot enough and the filaments are cooling down too fast. You can contact their after sales and ask them what to do about it.

Mines the same. Must bang it on hard lol

I’ve been having the same issue, but on an Ender 5 Plus since the last Klipper update. I’m thinking they shipped with that version. Hadn’t had it powered on in a week or two and it seems everything had new versions pushed. So I’m upgrading. Qidi have their Klipper locked down, but they likely have a new firmware version for you to install that might fix your issues

Is your model the new one with all the fixes and steel not carbon fiber? If so how's it holding up, and how does jut stack up to their 600mm/s claim?

Bob, I am looking at buying another truebore to put on a slant pro lathe. Have you done any chamber reaming? or is there not enough room on the lathe?

Which one is your favorite in terms of reliability?

Mine kept shutting down around 7-8 hours in on a print. They told me the same thing on the USB C cable. I got a 100w data with the 90deg connections off of Amazon, and I’m 21 hours in on a 36hr print. You should put some air over the cooling fins on the drivers. They’re probably hot to the touch, and most likely getting more power than they need. Mine were set pretty high especially on hold current.

What's the max print speed in this machine when printing nylon carbon?

i-fast seems better machine all around.

Would be great to see this print any Carbon Fiber based filaments at large scale :)

Let Qidi know about that, I hope this will be the only QC issue especially after all the upgrades done to the printer when they recalled it. I have a preorder and your videos are useful since you are the first on YT showing the updated version of the printer!

thank you for the video!

Mr. Abbott, we just purchased the X Plus 2. We've unboxed it, followed the setup instructions and so far, we're unable to load filament. It produces a clicking sound and never makes it through the nozzle. Any suggestions? Thank you for info and love your setup!