Відео

I have a Lancer sportback with no ac, is this literally the same thing? Its the 4g69 motor. Would it be best to just drop the subframe?

What is un loosen ?

Don’t buy jank bearings ever

But on a cammed 305?

Promo>SM 🎊

I’d love to the view of you starting it from inside the car. Show us what you do with the gas pedal and stuff

nice camaro brudder, currently working on mine. Needs some work but she will get there

Good video bro I’m working on same unit right now

😳 'promo sm'

Now how about the condenser

THANX

Thanks for the video sir

Please don't seat that bearing with an impact gun, torque it to a 133 ft lbs loosen nut one full turn retorque to 60 ft lbs your center support bearing is now properly seated and torqued.

Any videos with you doing the input shaft seal on the transfer case

The best marking/alignment solution to dissemble/reassemble is to use a metal punch. Use two marks on each alignment point. No paint pen erasure worries, though also using a paint pen just helps visually. I replaced mine at 70K with an OEM Toyota CSB in my 2006 4X4 CC Limited and 31K later it is still tight and smooth. I also used the opportunity to fully regrease and clean all u joints and spider bearings. Planning on keeping mine until I'm dead first!

Short and simple great job you do it and teach it like it suppose to be super job

Guys do yourself a FAVOR, EBAY has YOTA DIRECT REPLACEMENT Parts (which i bought) for way less then dealership cost and a hell of alot more reliable then cheap aftermarket replacements. This bearings too important to cheap out on. There's also websites dedicated to selling manufacted parts for toyotas WAY BELOW DEALERSHIP PRICES that are very affordable. The one I replaced on my truck was the original at 164k miles, I think I'll pay alittle more for the factory replacement then for a KRAGEN, or AUTOZONE part for that type of reliabilty and Part Longevity. JMO😎🤔🍻

You solved the mystery of what's causing the rumbling knocking sound. Unfortunately I have to take to the mechanic but luckily it a very good shop.

Thank you for the video good 👍

Do you have an contact number

Where can I buy a 2006 mitsubishi galant valve vent

Hello...how about a 2016 Mitsubishi Outlander that stops blowing cold air when I'm stopped at a red light or stop and go traffic??? Once I get going, it starts blowing cold air again. REALLY annoying! I have to put it in neutral and rev up the engine when I'm stopped, or I will bake. Freon HAS been properly vacuum and recharged...Any suggestions? Thanks!

Dumping refrigerant into the atmosphere is for losers.

He might be sure to let viewers know to Mark drive shaft so they don't flip it when they go put it back together

Hey man great video.. I just bought a 2000 2wd tundra, and I noticed a bad grinding sound in first gear only.. When I hit second gear it goes away. Also when I go from first to neutral it goes away.. Not sure if its because the shaft is spinning faster in second gear, or if it's internal with the first gear? Really praying this is the fix.. I did grab the drive shaft by the center bearing and noticed quite a bit of play. Should this be tight or do they have play? Also.. I was going to jack the truck up and put it on jack stands and put in gear while lifted to see where the noise is coming from.. thoughts?

Thank you for the "no nonsense/ to the point " explanation !!

Great video. Gotta change mine this weekend gonna start spraying it down today 👍🏾

Awesome! Quick and easy!!! Thank you!

Hey Tyler do you know where can I get a compressor from because in my area we don’t have any

Exelente video

AutoZone says that part doesn't fit my Tundra? It looks like a better product (sealed) and is about the right size. Could AutoZone be wrong???

Nice job! And looks great

Ours was a bit more difficult. We didn't have bolts on the shaft on both ends. So we had to press ours out on the front of the drive shaft.

The markings on my drive shaft got erased while doing this install. I have no idea how the two shafts were originally. Any ideas on how I can put it back so it’s not unbalanced?

You should never take off a\c lines without removing the refrigerant. This is not only illegal it's dangerous.

Great music choice 👌

Very quick and to the point thanks for the vid.

Como cambio la válvula a/c de mirage 99

Good morning! At min2:45 you have a cut that cuts out what you are saying, would you please clarify??

Could a worn support bearing cause the truck to wobble under acceleration? My 2000 tundra wobbles when I'm on the gas pedal but quits wobbling as soon as I take my foot off the pedal

Great video. Quick and to-the-point!

Is there any way I can make sure the drive shaft's lined up right ? I bought the truck used & the barring has been replaced ,so I don't know the shafts are right ... ? :-/ Link to Amazon says the U- joints don't fit my 02 Tundra ... ? SUBED / Well done video . Thank you.

Hagan un video cómo cambiar El retén que va en la flecha del diferencial de una Toyota tundra 2001

When's the next video coming out?

Thanks for the upload, great tips below as well.

Thank you so much this helped a lot

Can you do a video on U joint removal?

Can you describe the growling noise more please? I thought it was my front wheel bearings going when my truck started making a roaring noise, turns out it wasnt that, before i replace the u joints, should i have this replaced first to see if that is the cause?

If bad will it make it whine in first gear. Auntomatic