Відео

Thanks bro. EXCELLENT information and video..💯

Great work dude 👏

How can you tell when your out of line on the drain cleaner

never seen anyone do this before because it so f'n wrong. You don't use plywood that will wrought and shrink and expand. You're supposed use rebar and screen mesh. You diy morons never seize to amaze

What kind of concrete do you use?

Hey Willow Just wanted to say thanks for making the effort of recording all of this and posting it to youtube I‘ve managed to do it myself with no previous mechanical experience on motorcycles, & even found that three out of four membranes in the carb were torn which is why the bike wouldn‘t run well. Now all I have to do is figure out why the bike won‘t run in idle unless I turn the rpm‘s all the way up, it only idles at 4k rpm for some reason But anyways, thanks a lot again!

Good vid going to change my oil soon

Nice lanterns... thanks for sharing! You might want to try offsetting your glass so that the incoming air spins CCW, as the Coriolis effect in the Northern hemisphere spins in that direction. I think you'll find it produces a better cyclone... it'd make for a neat comparison video.

Do you have any videos on how to clean out the fuel tank? On the 01 yamaha ?

And by the way is still fucked up, it’s supposed to have an over the brick line edge to drop rain without run along the bricks

Yeah i get it he wanted to use what he had but ended up making something that wont last besides if you buying cement and sand just that goes more money them buying cement board

Excellent job and a good tutorial. However, I would not use the plywood. Perhaps some other kind of material like Hardy back or something less prone to warp of fire. Thank you very much!!

Does adding carb cleaner to fuel help?

Thanks for the video!! Great work!! I’m trying to bid this same job. How long did it take you?

Why not just fill it

How can I tell my zone numbers, I have seven and want to know which is which, thanks

I had a dude paint the crown after he installed it and now it’s peeling …. Should I seal instead of painting the new one ?

SMH you explain how to take it apart and put it back together but nothing about what you're looking for when you're adjusting. What an I looking for on the gauge?

Explain what you're doing while you're doing it. SMH. I watched a 10 min video, it should've been 5. Lol

E eccezionale sto strumento

Hello Willow thank you so much bro!!!🎉

Who see this wonderfull video 2024? 🎉

Hello, I have a section that doesn't work. I'll follow your video and keep you posted. One dallas irrigation wanted around $800 to fix my issue. Another question, my system has 6 zones on my system. Looks like yours, have you change out the main controller?

Is the plywood/backer board free floating until concrete is installed or do you screw the backer board to something?? Is the overhang of the hole 1” or what’s the backer board lip to edge?

Are permits required for this type of work ?

Hey man i know its a long shot on you responding. Are the two vent lines on the fuel tank important to have on?

Great video thank you! Very nice bike also. Ride safe

music sucks and is annoying

Plywood?

Ci vuole vasca ultrasuoni per pulire

Fatto io uguale

Thanks bro!

What happens if you didn’t prime your auger at first use 🥶?

+1 for using a magnet on a stick through the oil fill hole to guide it in.

why there are a lot of negative echoes on the R6 models from 1999 until 2001 that a lot of engine and engine block failures. And that models up to 2001 should be avoided. I found a 2001 first hand with 8000 km in almost new condition but I am hesitant for fear of ending up with an engine that fails.... I even had a dealer who advised me not to buy…. Can you tell me if you had problems with yours ? Or there is différence with Europeen models ? Thank you

Geniale.

Thank you! Very clear instructions to do changing oil & air filter on Toyota Tacoma truck.

Good job but the music is horrible!

Another tip, you can repolish jets and mixing tubes with 0000 steel wool. Leaves a factory finish on them that lasts

I've got a thundercat, is the process exactly the same? New to riding and (very) novice at any mechanics

Missing 1.5-2.0 inch drip edge. Water should drip onto roof not run down sides of chimney. Also cement is used for crown not mortar.

You need to start making newer videos. You have some quality stuff. This was great!

One of the best powder coat gun reviews I have seen. I not only appreciate the DIY fixes you provide, but the reason for the fixes were probably the most valuable. Great job! Thank you!

This video shows how not to fix your chimney

Need to use cement board not plywood

You're the best.

Thank you

Very nice ! Helped me out a lot.. Thank brother !

Hack

mortar. This isn't what mortar is designed for and it WILL NOT last. Mortar is used for masonry joints. Cement with rebar is FAR superior. Also, simply running a bead of whatever caulk around the flue is DIY mistake.