Відео

Hey how is it 2 years later

Researching for my rt200 mini bike putting this baby on it. 40 series torque convter already here end of thanksgiving the rt500 wolf welp with be howling down the road

Why wouldnt u have gotten a 18 hp kit ?

Hey bud!!! Tabatha the host here. What a great video!!! Thanks so much for the shout out. Caught a 56 lb on south beach last week. Bass are a plenty and the weather is awesome. Hope to see you guys again real soon.

I am looking for video(s) where people are able to use Honda or similar make petrol engines for conversion into outboard motors using 90degree gear box and a short transom . I hope to find some video on such conversion.

Picking my first 10ft Jon boat up today for 200 with a 30lb trolling motor and I have a Amazon mud kit on the way! Have a built predator 212 already with a stroker rod 20lb valve springs aluminum flywheel with advanced timing key and a 26mm pwk flat slide carb! That thing should fly don’t you think? Taking it off my mini bike that goes 50 mph the engine runs at like 6600 rpm

been wanting the 16hp 420 build on red beards garage chanel takes it to 40hp, it's the biggest engine that would fit in my engine bay without modification

I think it’s less messing around putting a mukini carb on it and just taking the electronic stock carb off and ecu. Then just hook up a key ignition lol

Awesome

I tried it on the chainsaw and the Velcro would not hold it in place. It would vibrate off after a while..

Do you know why the idle is so high?

Does this have an electronic choke? (Auto or manual choke)

Hello, first off, thank you for a great video👌🏻 I am running your system with a small NOCO lithium 500a battery that has been working great at starting the engine as well as running the electric clutch on the pto, but these lithium batteries are at 13.5 volts static charge. I’m wondering if there is a regulator that would allow for a higher charging voltage for this kind of battery? Nelson

Thank you!!!

Looks awesome. Where did you get the sun shade for the boat? I’d like to put one on mine.

Haha.... I remember seeing you on the water. We were at Sh!t Creek when you went by. Great videos bro.

Where did you buy the kit from?

There's a law in physics that describes the correlation between exerted force increase equals more resistance regardless of material force, even in vacuum

What kinda application is this going to be used for?

What size prop?

Absolutely cannot wait for this bad boy to be on the 10ft

Is governer still on that motor ?

Did you ever replace valve springs or fly wheel? It’s really ok after all this time with govner delete? Did you have any issues? I have the same motor and same long tail kit I hope you reply haha. Thanks!

Would I have to re jet or can I just add this exhaust with everything else stock?

can you fit 3 onboard? would love a response as its whats making me decide between this and the 1236

Nice setup. what is typically the best bait for flat head?

High low rig is even easier & does the same thing. keeps bait raised off the bottom a little bit.

Been using a similar rig to that for the last 55 years. We typically put the swivel on the loop for the hook and we never tie a knot on the loop, we just run the loop through the eye of the swivel, and then put the swivel back through the loop end. The Hook can then be taken off the rig for safe transport! Your rig is fine, but looks like a LOT of extra work to get the same thing we use. Most of the time it's the hook that snags/gets hung up and with the swivel on the end of the loop, you lose the hook and not the lead sinker, rather than the whole rig.

that's pretty neat but what do you do in the case of snaggs does the swivel just snap or the hook or the sinker and is the swivel the weakest point of the rig or is it the knots just wondering if you had to deal with that and how you handles those

I just got a 1752 bare mod v boat. Bottom is beat up. But my 22 predator swamp runner should move it okay right ?

Very cool, I'll be trying this soon. But seems like this is best for braided line, not for Mono...? I feel like the knot that creates the "drop shot - 3 way" would be a weak point on Mono... one way to find out I guess.

What rectifier diode is being used?

hows the 500 held up?

lol. I'm the dude with the orange Crosstrek.

Was curious to was the setting was on the tachometer and how many wraps? Thanks

DuroMax dog killer

Thank you for making this video! Any chance you have a part number for an upgraded flywheel that outputs more power?

in have a 10ft jon boat also i welded a trolling motor mound to the front and welded a bracket for a 12 inch light bar i built flooring for it with carpet and i have a 6hp jhonson with it the weight really levels out with it

how did you hook up the throttle?

Is this the same engine that had the surface drive on it? What made you swap?

Always been a favorite spot on the river. Nice catch! Like your rig too! Thanks for sharing

Amazing catch of those fish 😎😎😎👍👍👍👍

@11:50. Why can't you just push down like a long tail to pop it out of the water? Oh and how fast with the 2 of you?

Still running good ?

for 80 so dollars u get that thang rrrrrrrrrrrrrrrriiiiiiiiiiiiiiiipppppppppppppppppppppiiiiiiiiiiiiiiiiiiiiiinnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn

Interesting you caught that huge fish on a small 'salty'. Just shows that it's not always the big baits that catch the big fish.

How do I do this if I have a thumb throttle

What bolt where you able to put on the shaft? the one provided was too small for me and idk what bolt to use

What’s your Top speed with this set up sir ?

1030.. 1032.. 1036.. 1040.. ALL 10 Ft JON BOATS.. BUT WHAT IS THE BEAST..?