Відео

@@phillippearce9680 thank you

I hadn't even thought of that until someone else had suggested to me too.

I did do a review in a previous video. Still it's a good machine that I've put a lot of wire through. The speed thing I've heard about from one other person. My machine doesn't do that but it is about 2 years old.

@@HoodTimeWelding copy that thank you for your response. I do love my Primeweld just wanted to ask . Great videos 💯

@@charliehuntsman9827 thank you for the feedback I really appreciate it.

Thank you. I had a customer looking for something a little different. This is what I came up with. I should actually have it totally finished tomorrow so the video with that should be out Thursday, May 27 at noon. Have to see what you think of that.

I thought about that but you are still dealing with some different curves and depressions with one big piece. It was easier I think to piece it like I did.

@@HoodTimeWelding your probly right , it took me like 11 hours to do one of these . I used 1/8 for a little extra life span

I had no way to check them. What you might not have noticed and I didn't point out is the plates already on there had points where the bolts holding the rings in running through them. So this was part of the reason I didn't remove them. They were holding the pulleys in place.

Solid wire .030 ER,70S-6

The bottom hupping up was more about me not being in practice on doing 2". Having to move quick and all. In the 9-12 and 3-12 the weld laid in the joint really nice.

Sorry I didn't respond at the time but I really appreciate the feedback. I try to do honest reviews.

You do have to run the grinder down them quickly on thicker stuff. You can feel a little edge.

Glad to hear I could help out!

1/2' thick mild steel, but it can be changed to meet people's needs.

That's where I got the thought. Looked for them and they cost $20 a piece and so I just made them.

Thank you. I try to come up with something a little different on each of my giveaways on Facebook. If I get enough subscribers on here I'll probably start something on here to.

I'm glad the video helped you make a decision.

Thank you. I tried coming up with something a little different and the customer loved it.

These type of bits work on everything but concrete and cement so if you can find one in 4" I think you would be good. They chew right through steel no problem.

www.amazon.com/ASNOMY-Tungsten-Carbide-Titanium-Plated-Stainless/dp/B09MT4YQSH/ref=mp_s_a_1_2_sspa?crid=ZKF1B8O9QC4R&dib=eyJ2IjoiMSJ9.lMnWjQzYfogZzFVgklW_IXAX4ClAucoSVUWVlzuMPkj3d2priMBb7qY3vIjeeUqTsxEiWLWeQ17UvujaFGWlayuufiYbOkOep6_DsXzEq21nO1AHU6nkGMUDb54bXA4nkaFGZ14kt2VN4Aa_-B3Q1RKSS2CHsvkrvhlhY3fAzV11STytTIgM3i_7ylgfq3A6TMOqehrsxiYKcHV2CCmrlw.QYKOKS1gVQeZlgJd8TFH31KrkCSVJAN-sOcJgpY0u1U&dib_tag=se&keywords=4%22+heavy+duty+hole+saw&qid=1715739670&sprefix=4+heavy+duty+hole+saw%2Caps%2C130&sr=8-2-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9waG9uZV9zZWFyY2hfYXRm&psc=1

I'm really glad you enjoyed it. I try to be informative. I also have a video of welding with it if you are interested.

I try to share tools that others can use and work well. Thanks for the feedback.

Thank you.

Thank you

I got lucky that my neighbors sold it to me for a great price and we are able to afford it. I had looked on it enviously since I had moved in 2 years ago.

Thank you for the input.

If I remember correctly it will not but if you put it at 40 degrees it will. It just catches on the safety stop on the one side.

Truthfully I'm not sure. The concrete I was drilling was old stuff which is usually pretty hard in the center.

It does function as a regular drill but I find it a bit high speed for that. You can feather the trigger a little to help with that.

Thank you, I try.

After thinking it over I thought of a couple of things. Maybe try to blow out the liner. Second maybe a kink in the liner. Check your feed wheels and the tensioner. Bad wrap on the roll of wire. Without being there sorry I can't help more.

Thank you for the feedback. It's nice to have a different perspective so I can make better videos.

It was fabricating the stop for the bandsaw. It makes it still portable and you can use whatever steel you have on hand to a point.

Sorry, I was just going by what the customer told me. He had only brought the deck to me.

I run my die grinder, needle scaler, and also my plasma arc machine. The plasma arc runs at around 70lbs pressure and it keeps up. It usually starts running after I get going but keeps up.

Thanks@@HoodTimeWelding

​@greggc8088 you can get a tank ot buy a broken air compressor on offer up. Take the motor off, close it up, and connect it to your 21 gallon. Use it as an auxiliary tank. You'll have air

I had my buddy heater going and it warmed up. I was thinking about a new base but they were talking about a new chair in a bit so I didn't want to go overboard. Thanks for the comment.

Thank you. It's nice to hear.

Thanks. The hole needed to be fixed for inspection to pass for the customer. I always try to go over the top.

Just picked one up today.

I was lucky that day and it wasn't windy. The little I had I was able to block with my body.

@@HoodTimeWelding What state are you in? I live a couple miles from the ocean so it's windy from every angle here in Melbourne FL. I swear it rains upwards too.

I live in northwest PA.

It's actually a customer design with a few refinements by me. I extended the bar down into the plate to give more support instead of doing a butt joint.

I have not. I use it so much for MIG I give it a break when I have to stick weld. I will say the 225 runs stick great and since they are both made by Primeweld I think it would too.

I haven't noticed that. Mine seems to dial in right at what I want.

@@HoodTimeWelding thanks for the reply back I figured that guess I gotta message them.

@@ab75901 you can also call. I had a problem with the whip , talked about it on my welding with video, and got answered right away.

@@HoodTimeWelding I may have to Monday but usually Dustin I think is his name messages back pretty fast and problems solved faster then I posted this, they have best customer service I have ever dealt with.

Well they were going to send a new one then he said that it’s normal for it to go in increments of 4 but haven’t got a response to why it barely welds 1/16 maxed out, my luck everybody loves there’s but I get a Chinese dud that they act like they don’t want to fix the problem 🤣

This was just a customer's deck. Everything else looked good at the moment. I'll keep that in mind though. I also did another deck that I did a video on. Cub Cadet that time. Those seem to be weak around the spindles and like to rust there. Like you said, a little work and you can get decks to last longer. Saves money. Thanks for the comments.