- 6
- 38 228
Casfer
Приєднався 8 вер 2020
HP Latex Carriage Assy and Belt Tensioner Assy Replacement
HP Latex Carriage Assy and Belt Tensioner Assy Replacement
Переглядів: 21 771
Відео
HP Latex 300 series PIP Floater and sensor Replacement
Переглядів 7 тис.4 роки тому
HP Latex 300 series PIP Floater and sensor Replacement
HP Latex 570 Scan Axis Motor Replacement
Переглядів 4,8 тис.4 роки тому
HP Latex 570 Scan Axis Motor Replacement
HP Latex 570 Curing Heater and Fan Replacement
Переглядів 4,3 тис.4 роки тому
HP Latex 570 Curing Heater and Fan Replacement
Hi there, I recently just purchased a latex 570 used. I’ve had a bunch of issues with it and your videos have helped me out a ton. I wish you could still make more. Best videos on UA-cam for these machines. I’m having a problem with my machine not waking up sometimes when it’s asleep or it goes right into sleep mode a few minutes after it wakes up. Do you have an idea what this could be? Thank you
do you have video to install color sensor on HP 365 latex Error code 58.12:10
HP 365 here. Definitely helped seeing how to take off the head for our snapped belt. Thank you!!!!
Thanks for showing the order of the parts needed to be adjusted, cleared or removed before the belt repair is made. During the video the print heads were removed. After the encoder strip was put back, that was the end of the video. Is there a specific procedure in putting the print heads back into the carriage?
Not really, just put them back on in the same order, after having put the carriage all together again; no need to run any calibrations. I did a printhead status plot just to make sure. In the service manual it asks to reset the belt cycles from the life counter. I just did the whole thing and this video, even though not perfect from a photographic point of view, really helped in the more critical parts.
@@hannybasso7047 Thanks, I did just pop them in and the printhead cleaning cycle ran a few times on startup. I can tell my printer dealer that an un-authorized technician handled the job just fine! Without the video I may not have tryed to make the repair.
Thx for this video - today, I did not change just the belt but also the M3 screw, which secures the left tip of the encoder strip. I trusted that there was a corresponding thread behind a 13 mm width across flats. Unfortunately, the assumption was wrong - Knaaack!
all my ink catridge missing, latex 365, how can i fix it sir?
Hello, i have change the belt but i have recived error 86:01 - and the ink cartige colector ejecting him self? if it is posible can you give me a hint?
Hi, how to introduce the number of the new sensor in the service mode in plotter, the service mode is protected by password. Do you know what the password is?
It's HP Latex 330
Hello guy, pls you help me something. Is there parameter to be set after finish replacement? Or it can be used immediately? Thank you very much.
Hello mate. Is it also just a matter of replacing the ink cartridge if its faulty?
my hp 335 not printing as per file size. print is much more shorter than the actual print size ..plz help
This video does not show anything wort mentioning. It is the worst video I have haver seen. You can't see were he is losing all the screws and how he is putting on the tension belt back in the bottom of the Carriage Assy
You the GOAT fr 🐐❤🔥❤🔥
How do you access the enginer service menu ?
nice video!
Have you ever changed the hp latex 570. 3L connector. It says i have leaking at the tank side.
It will not be the 3L connector. Leakage will be detected by the PIP sensor. In this case, you to find if the leakage is from damaged intermediate tank or the PIP sensor itself. And you need to find which color your having the leakage.
@casfer4998 The code i have is latex 47.5:11, and i know it is OP 3L. I wish i could send a photo to you. I see the cable was wet at 3L op connector.
@@rahmigokcedag4895 So in this case, you need to change the OP 3L ink line. Once it is replaced, you also need to clean the ink tray and leakage sensor need to be dry. You might need a guy who is trained on HP to do this because there is a procedure to purge the air along with the new ink line.
@casfer4998 Thank you. There is no way to unfunction 3l tanks and use only the smaller cartidges. Is there a way to do it? Turning off the bottom part completely
Hi Casfer, I have been dealing with a 86:01 on a Latex 370 for about 2 months now, supoosed paper jam there is no media, I am suspecting Axis motor but that was replaced along with belt and 3L PCI about 2 years ago,I have checked encoder strip and tensioner. Could you please help?
Hello! 86:01 is scan axis movement issue. This error is related with the scan axis motor or encoder reader or encoder strip or the carriage bushing. There are many things to be consider. Is it stopping on the same position? You can also try to move the carriage manually by pushing or pull with hand while the printer is off then see if there is a lot of friction on it.
can you tell me what type of fabric is used in the L330 printhead maintenance cartridge? I would like to change only the tissue and reuse the cartridge again
I didn't see you bleed the air out the ink line. ???
Casfer, let's say 3 of the ink tanks dont recognize them. And there was no error at the printer. Could it be PIP issue?
If there is a problem with the PIP sensor it should show error. Are we talking about 3 inks tanks the same color or 3 tanks different color? What is the model of your printer?
@casfer4998 3 different one m, lm and lc and there is no error.
It says missing cartidge even though it was installed
@@rahmigokcedag4895 did you try change any of them? Which printer model do you have?
It could be just defective cartridges but it is strange to get damaged 3 cartridges at the same time. On the printer panel you will find system error and system warning, check the codes on it.
Thanks. The HP 365 service manual under 'Belt Assembly' also has this process step by step.
hi! i have a problem - my latex 570 keeps printing in the same spot. the media does not move well while printing. it loads ok, moves it ok. but when i need to print - it doesn't move. only if i use TUR and if i help it with my hands. You know when it can be?
What media are you using? Is it happening in all your media? You can also try to clean the main roller.
@@casfer4998 thanks for an answer. it happens both on paper and vinyl, yes. Like on 5 different media types (all paper and vinyl. The they do move, but they slip under the paper. I did clean all the rollers one by one several times with rubber roller reviver. so they are like new! Didn't help. I also did check the lever that clamps the paper. It is ok. what is the main roller?
and where the main roller would be, couldn't find it on google
@@prostoposter The main roller is the one under the pinchwheels. You can have an easy access on it when you open the back cover.
@@casfer4998 i will try that. if it doesn't help, can i please contact you again? Because honestly i'm very confused. Been to lots of forum etc and no one is able to figure out the problem. And you seem to know these machines very well. thanks!
How far apart do we space the metals on the belt so the cartridge moves and does not get jammed in placed?
Look under the carriage you will find a label or sign where to keep the belt metal joint.
Hi, well I also just want to say thank you and ... fire that cameraman 🙂
I changed the PIP sensor Cyan one. I did everythjnf correctly then i install thr samr ink cartridge. It did not recognized. Do you think it is the cartidge chip or there is some other issue?
Hi, did you input the new PIP Calibration value? What was the error before you change the PIP?
@Casfer i dont know that value setting and where to do. I had 25.4:10 Cyan Thank you by the way. I have been learning a lot from you.
The value is actually written on the new PIP. It could be your IT tank or ink cartridge is already damage as well.
Got it now. Looks like the previous sensor burned the chip out. New cartidge works well. Thanks
Where do you input this values to? What menu option?@@casfer4998
Can you make a video for cleaning all the curing unit including heaters from dust?
cameraman….😢
Hi Dear, First of all I want to thank you for the videos, its really helpful. I have a hp latex 360 and getting the error 16.42:10 Module 2 ( right to left) faulty or not connected . Line # 1403 . I was wondering if you know what is the part number or any suggestions. I would appreciate. Thanks
Hi, 42:10 error is related with the scan axis motor. You can order this in one of your hp support provider in your area. But first try to clean the carriage rod and lubricate it with oil.
sir i'm crying why the hp latex 375 machine has an error and the code 25.1:10 appears
sir i'm crying why the hp latex 375 machine has an error and the code 25.1:10 appears
sir i'm crying why the hp latex 375 machine has an error and the code 25.1:10 appears
Selamat malam kak Ada yang mau saya tanyakan
Greetings am from Zambia looking for a belt for z6200 designjet machine or any recommendations where I can buy
👍
What he don't show or tell you is that it takes two people to put the encoder strip back on and the spring tensioner only goes on one way. there is a slight offset with the screw hole. So when you have the carriage upside down putting the belt on, the tensioner spring must be facing down so when you flip it over you'll be able to see the spring open side. Still thanks for posting this video, It did help!
I accomplish the encoder strip alone, just let the right side metal piece loose without the screws just the strip screw few turns to hold it, install the tensioner on the left side, then tight the metal piece on the right side and is done u can now tight well the little screw to make tension on the encoder strip.
great video thank you had to replace my belt came out good
I replaced the pip and the printer is still showing the error message when I power it on? Any thoughts on how to resolve this issue? Thank you
Please do another video next time you replace a belt using a different camera person. Who ever recorded this video probably had so attention disorder or clueless
Can you make a video on replacing the foam pads the two small ones for the head
Hi brother, can I have an Email to contact you? I need support for my Latex 360. Thank you
Can you do one on color sensor replacement. Please!!
Hi Robert, there are only 2 screws(T10) holding the color sensor from the carriage, plus the flat cable connected on the carriage pca.
hi can you help me how latex 315 error code14.87:10 and14.83:11
Why did you replace the fan? My 560 is bunching up the substrate and causing head crashes… the material heats the curing tunnel
Raphael Philip Do you have a similar video for the L25500. I need to know how to separate the ink lines from the printhead carriage. This is where I am stuck. Thank you
Would you post a video of you removing the cover? I believe I have all screws out, )except one and it is super tight). Thanks
did you get the cover off? Can you tell me how you did that?
I cannot get the cover off of my printer. Is there a trick to that? Seems like the top screw inside the cover won’t budge.
Great Video, I replaced my HP 360 belt myself with a new belt and pulley from eBay for just $165 - Thank you
Hello guy, pls you help me something. Is there parameter to be set after finish replacement? Or it can be used immediately? Thank you very much.
@@chaiyapornsribuabal978 I just replaced on a L110mine using this video. I just aligned my new belt to the old one making sure the metal coupler was in the exact same place. I didn't take apart the left side because I could reach the gear. Turned on the machine and didn't have to do anything else.
Hay que tensar mucho la correa
Hi, I have a 42:10 error. I checked, cleaned, and oiled the bar. But there is no issue. I believe that is the solution to what you have done. Do you think is there any other thing that might cause it.
42:error is an scan axis motor movement failure. Since you already cleaned the carriage rail. Try to clean as well your encoder strip look for any dirt on it. Otherwise it could be the carriage motor itself was damaged.
@@casfer4998 Thank you so much. You make everything so easier. The interesting part is the head can move to the left side without any problem. It stock at the left side, while trying to move right. over the ink section.
Did you check the encoder strip if it is ok. Then it could be the carriage motor. You can ask for it from your hp authorized distributor from your region.
You are the best. Thank you for your answers. I fixed my plotter with watching your videos.
Your most welcome! Cheers!
1- How to clean hp latex 381 printheads manually? 2- how to repair them? 3- how to keep them well? Any manual or video? Thank you so much.
Hi Dear 26.1:10 Error Code, I replaced the PIP, but same error. Could you please help me resolve this issue?
Did you run "Recover broken bag" from the Diagnostic. If yes, then check the IT cartridge, otherwise you might have a problem on the ISS board. Look for any ink drop on the ISS. In case it does not help, look for authorized hp tech in your region to help you sorted out the issue on site.