Відео

@mostcailmerob . That’s a Schinciders I picked up from harbor freight.

@No-rh6zp . No problem glad it helped you out. When you get the programmer and change your motor direction make sure you set the end points again 👊🏾💯

@@LBizzyRC ok thank you so much

@No-rh6zp . Turn on transmitter make sure your throttle is at dead center. Then hold the power on button on esc for 3sec then release it should be blinking that’s for neutral hit the power button once to set then pull full throttle while holding it hit the power button once that sets full throttle go full brake hit power button that sets brake when you release brake it should calibrate start blinking turn off esc and then back on and it’s set.

@ ok thanks I will tell you if it works

@@LBizzyRC it didn’t work I’m having a lot of issues like it does not stay set and when it decides to work and I turn it off I have to recalibrate it and it sometimes doesn’t work can you make a video please I can find any other videos

@No-rh6zp . Hope it helps just unloaded a video

@@LBizzyRC ok thank you so much

@gonzodetroitify . Just some 3m double sided tape the grey stuff it’s super adhesive 👊🏾💯

@TheRealStuntShady . That’s the stock pinion , I used a 5/64 drill bit to bore the pinion out for the motor shaft.

@@LBizzyRC that’s what’s up brotha appreciate the reply! Have you been able to get it out and rippin yet?! Just ordered the same setup can’t wait to get it in the micro b

@TheRealStuntShady . Nah haven’t been able to run it at my local, It’s bout an hr drive but running it in the living room it’s really smooth, 👊🏾💯

@patrickmcdermott6603 . Yes the new system is so much better than the first gen no complaints at all 👊🏾💯

@g.b-MTB-trail-jumps3062 . Thanks 🙏🏾 for the continuing support

@voodooreptiles3553 . But enough power makes them a blast, 3s is stupidly unnecessary. With the right setup on 2s is 💰

Buy the new hobbywing fusion 16 all in one it's 3000kv that's plenty of power for a grom

Plus you don't have to find a place to hide the esc cause it's all in one and not only that but the fusion 16 is only $59 right now on hobbywing website. Ps mine even came in 4 days lol it was actually 3 days early

@Diaszurana . For the short wheel base that motor wouldn’t fit its to long, I would look at the Hobbywing 16BL30 combo.

Thanks, guys

what motor is that mate? can you put part number

@davidseychell . Thanks 🙏🏾 much appreciated 👊🏾💯

@Fx4RC . Sounds like you’re gonna have a few more Groms 🤣😂. I’m definitely liking the new color scheme though 👊🏾💯

@varroniz . If I can get my hands on 1 🧐 I would certainly try too👊🏾💯

Do you have instagram account??

@varroniz . I don’t have IG.

Would you be willing to mod it for me if I send you one??

@varroniz . I would say yeah but don’t want to make a mistake and be able to do it. Don’t wanna feel responsible if I can’t get it done. Imma get one so I can take it apart and see what’s going on inside to see what can be done.👊🏾💯

@TexasWaters . Nice!!!! Yes indeed lots of power🦾

@Dankboi420 . Yes no modifications needed

​@@LBizzyRC Thanks man. Just bought this combo for my big rock running on 6S. Huge upgrade from stock

@Dankboi420 . Nice !!!! It has that low end power lot of settings in the esc to adjust too. I haven’t messed wit yet but you can fine tune to your liking if needed. Bash on bro 👊🏾💯

@francoismuller9735 . It’s an improvement so many options in the esc to adjust to your liking 👊🏾💯plus it sensored!!!!

@Stonew24 . This set up is great haven’t had no issues at all just make sure the diffs have the right amount of fluid and wt and you should be fine👊🏾💯

@konfyoused .Thanks those are the 4s kraton shocks and typhon 6s katars

@iambigsteveo . Yes I got the AVC dialed in pretty good 👍🏾

@@LBizzyRC do you recommend avc for racing around lots like you are doing here?

@iambigsteveo . Yes it just makes the RC feels so much better, its a different experience especially when it’s dialed in. 👊🏾💯

@Hungrybird474 . It’s a pretty good system lot of options to dial it in, might need to get 4s diffs for your granite if you keep blowing them👊🏾💯

@Hungrybird474 . Nice 👍🏾, love my max6 G2 glad Hobbywing went sensored and blue tooth with it.

@Fishing_Obsession87 . It got a lil warm a fan wouldn’t hurt tho, but im not running one don’t really WOT all the.

@Hungrybird474 . If it’s the G2 then yes it’s Bluetooth and how you can set your end points

@phyoaungkyaw85 . That’s on 8s

@mattgrill7713 . Those gears are 1.5 I got off eBay, king hobby is the cush drive and I believe the pinion are the NHX mod 1.5.

@keyriekalyan9273 . Sometimes you have to change your servo settings on the transmitter from normal to reverse

@@LBizzyRC I have tried all off the above.....I will take a video too post for folks too see what, am I doing wrong. Could be an easy fix. Thks

@keyriekalyan9273 . Yes if you have a mount for it

@Diaszurana . If you go 5690 you will definitely have to gear up and run 8s all the time to get the potential of that motor. 4990 you can run 8s or 6s and gear appropriately to your likings 👊🏾💯

@LBizzyRC I figure as much, but with the torque of the 5690, I can gear it to the moon. My concern is that maybe the Big Rock is a bit to light for the 5690, and I may have trouble keeping the front tires on the ground. The 5687 Gen 1 combo I have in my XMAXx is almost too much for it lol.

@Diaszurana . Yeah that 5687 flings that plastic Xmaxx like it ain’t nothing 🤣🤣😂🤣

@LBizzyRC It really does, though, 😆. Jokes aside though, my XMAXX with upgrades weighs 23 lbs. That's a lot heavier than the Big Rock.

@chiasson65 . I had a spare arrma esc plate laying around, had to dremel the side that goes close too the chassis brace. And attached that to the Losi esc bracket the holes line up then screwed it back down the the chassis, then 3m tape it down holds pretty solid for me. But still waiting on someone to come out with a mount 👊🏾💯

@@LBizzyRC thx bro. I did a different install today after some thought. I dremmeled out the center divider on the battery tray so I could use my big 6S, 6800 mah lipos. Then I installed about 8mm of HDPE plastic in the front portion of the battery tray to make it level. I then installed the ESC on top of this plastic …….so I have a big lipo and the ESC on the battery tray and the new 4990 motor in the original position. This is my first G2 esc……I didn’t know the fans on these run “on demand “

Ps. The diffs need thicker fluid…..but I will wait until winter to change them out.

Most definitely will be doing the same might go 100k 500k 100k👊🏾💯

NICE !!!👍🏾

@spenn2007 . Yeah I upgraded my firmware in the 08. Kept that stock didn’t mess wit the punch. Had the 30t pinion esc got over 190 went back stock pinion and it’s still a monster 👊🏾💯

@MrCyruskrakow . There’s no bleeder nut. I just filled them bout 90% would recommend 2k silicone diff oil or 3k.

@djp2257 . Make sure that your throttle knob on remote is dead center at zero before calibrating. Sometimes if it sees a a signal either way it won’t calibrate

@faisalbaig5306 . So far so good🦾 definitely loving this system in it👊🏾💯

@@LBizzyRC hows it holding up Boss ? thanks!!

@faisalbaig5306 . Got about 10 packs through it. 🦾 still going strong no issues at all working on a video to put up soon 👊🏾💯

@@LBizzyRC thank u so much! That is fantastic to know! What pinion are u running ?

@faisalbaig5306 . I’m running a 17t pinion

@Diaszuranna . Yes Fahrenheit.

@@LBizzyRC Damn. That's so much better than what I was expecting. Thanks for getting back to me

@Diaszuranna . I had to look at it again when I got home to make sure sorry that was Celsius my bad for the confusion. And the ambient temperature was about 80 that day. 👊🏾💯

@LBizzyRC That makes more sense 😆

@ianjohnhorwood2605 . 🤣🤣😂 Not sure how fast, really didn’t WOT for to long just getting a feel for it.👊🏾💯

@rccarsandmusic2641 . Will definitely run smooth on 8s, thinking of putting one in my infraction 🤫👊🏾💯

@Garage_unknown . Thanks 🙏🏾… I just felt like the motor was too small and would get to hot for that size scale…yeah I’m hoping the diffs hold up well will see 🤣🤣🤣😂👊🏾💯

⁠@@LBizzyRC Am interested if those poor drive cups and bearings are going to hold with the increased power and drag from bigger tires and electronics. Keep us updated, thanks.

@josephlucas753 . Thanks 🙏🏾 …it handled way better then I expected 👊🏾💯

@spenn2007 . 😂🤣🤣😂👊🏾💯

@jimborghini2761 . It will be hard to hide 🤫 😂😂

@jonspikes4935 . I see that could get annoying after while , hopefully the lipos don’t catch 🔥 🤣🤣 👊🏾💯

Way to expensive for a 1/6 car with 1/8 parts.