Відео

Hey, check this one out. Look through his other videos as well 🤘🏼 ua-cam.com/video/7u0c50zWWis/v-deo.htmlsi=CBgfVaALngjYZuWk

i cut mine on one side, easy to weld later

Off the top of my head, I think you need 12-15mm sockets/wrenches. I might have used a 10 or 8 on a bracket or 2. 21mm for the crossmember. 24mm for the crank pulley bolt. Some pry bars. Trans jack or other means to maneuver. Lots of extensions and/or wobbles and universals to get those hard to reach places. This is all from memory form a few days ago since I had to pull it out again, so I might be off a little. Have fun!

To my knowledge, yes you should be able to. As long as you have the torque converter also. The only difference in those transmissions is the planetary gears,the number of friction discs, and input shaft (which is why you need the torque converter). Also, make sure that if you have a 2wd, your get a transmission from a 2wd, and likewise for a 4wd. The tailshaft housing will be different from 2wd to 4wd to accommodate the transfer case. I would do a bit more research to verify. 🤘

@@SuperAwesomeGarageTime thank you so much for your response. I just had an engine put into my Cadillac about 4mts ago and now my transmission is acting up, I also have a 05 Tahoe that's just sitting around and I wondered to myself if it would be possible to use that transmission from the Tahoe, just trying to save a lil money. I will run this by my mechanic thank you so much for the info I really appreciate that.

@@icorp3942did it work?

Sorry about that, I was still learning the ins and outs of editing. Hope you were able to at least pick up what you needed from it.

Every time I get those horrible rust chunks in my eye I tell myself to go put some safety glasses on....but then I don’t....and I end up with more rust in my eyes. Being dumb hurts.

I too have had to play that silly game many times on many vehicles. Working on vehicles in Florida was great due to no rust on the local vehicles......but then there were those snowbirds from up north....

We need to find the person who did this exhaust work and make them answer for their sins!

Hope the video helped!

🥴🤤🥴🤤

I had a pain in the ass aligning everything for the 05+ hpop system. Did you run into that also?

@@SuperAwesomeGarageTime yes and no i first tried to save 100 bucks and reuse old branch tube but the old one was slightly tweaked and i matched the rocker boxes and rails together i was lucky i bought a garage full of shit from a guy cheap i know late 04s look same but some differences also stc fitting should go in hpop 21/2 turns i believe

i used 05 heads also but you can get away with not bolting rocker boxes if they don't match heads by using glow plug harness as alignment the actual head studs will hold them down fine just don't use 03' glowplugs in any other year they are longer and will hit pistons

Hey Deborah, i used valvoline full synthetic ATF. Compatible with many common types.

Dexron VI I believe

If you know what you are doing and don't run into any issues probably about 1.5 hours on your back. Around the same going back in.

After my first few videos I made I started realizing that in the editor it was quieter, but after processing and uploading for some reason the music would over power....same in all my other videos with music 😔 Thanks for the tip though! Learning as I go 👍

@@SuperAwesomeGarageTime did you do the rebuild video on the transmission?

@@juancortez4428 I sure did. If you go to the chanel page there are 2 videos of doing the rebuild (had to wait for some parts to complete it), then a test drive video after completion and installation. 🤘

I like that render! Pretty much what I was imagining. The only thing I forgot to mention was a table saw, about 3x4 foot. What details were you looking for?

@@SuperAwesomeGarageTime Ceiling height; dimensions of the patio/overhang, also how you plan to access the storage on the second story. I assume the Gambrel roof will have the slope facing the front/rear? I didnt show any roof here; but if you want to have a door that opens to the deck; It might look incredible; but also might be a bit taller than you'd like. The tool i used to make that model is free online; and i made what you see there in about ~15 minutes. if you've never used it; it could probably save you a ton of trial/effort and time modeling it.

Like this; for example. ibb.co/gjt8CD0

The first floor would be 6'6 and the second floor peaks at 9ft; so a total of 15'6. (I also scaled this all down a bit; because the doors are 6' tall; where as a standard door is 6'8)

I read something saying that the blue is supposed to be for government fleet vehicles. Wonder how much truth there is to that?

@@SuperAwesomeGarageTime Hard to know where the fuel suppliers load the tanker trucks

I'm gonna go Gargamel on their little blue asses for making all this work for me!

I agree entirely

Super Awesome Garage Time We’re usually on the same page with these things

It's only because our mothers raised us wrong

😘🥰😘

Super Awesome Garage Time still in VA?

Fo sho dude

I tried.....notice there are less at the beginning and more towards the end.......it's just not in the cards for me.

.....prove it!