Відео

Worth mentioning is that H110 and W296 are the same powder so 100% interchangeable

A few years back Smith and Wesson built some .357 mag. revolvers that would not stand up to the maximum pressure as stated by SAAMI in loading manuals. They were able to get SAAMI to lower the maximum pressure in loading manuals. When loading for newer revolvers you will need to make sure you use a newer reloading manual. There is a difference in maximum powder charge in all my older manuals than there is in my newer books. It may only be a problem with newer S&M revolvers I don't know. Just be aware.

That load gets me 1750fts with XTP from a 20' Winchester 94. very accurate too.

I'm sure it 5.56 pressures!

Nice range you are truly blessed.Mount a patio table umbrella in the bench and you could shoot all day..

What pressure do you think it's hitting?

Wow!! What a difference..

I dont blame you at all..The larger 30 cals are for the youngins..But, may I suggest, wearing a PAST recoil shield..It does wonders for your shoulder and state of mind..Wear it under your shirt..

Hornady is selling 75 grainers @ 2790..You can do it..🎉..Do you plan on trying this same test with different bullets?

Recently purchased some H110 for loading .357. Tried using 16 grains to push some Missouri bullet co 158 grain SWC. Pretty decent accuracy and felt some nice recoil. Trying to keep it a tad light since I use a SW 65-2 which is over 40 years old. Thanks for the video.

nice information ive been looking for. tell me did you start with standard primers or go straight to magnum primers? thank you bro.

You need to change bullets. Never had good luck with hot cor speer in my ruler RSI International. Best load was 36 gr 3031 , 75gr. Sierra hp. We'll prepared cases,Win. primers. 1/2" grps at 100 yds and 3/4" at 200 yds. And that's no BS. Out of an 18 1/2" barrel. It's all in the components being assembled. Search for what your rifle likes and stress on case preparation

My 99 loves, loves, 87gr Speer Hot Cor’s over 37 grains of IMR 4064, running 3050 fps. Accurate 💯

Was the first shot no ear pro 😂. Thanks for continuing the video afterwards haha

Would you be interested in selling the Ruger?

Just bought me one of those Little Dandy powder loaders ; didn’t realize i also had to get rotors for it. do you recommend this product? Thanks for the video have fun plinking

You’ll need to replace AK pin retainer because “ paper clip” 👎🏻

I need to replace my front sight on my 686+. I was thinking about putting a vortex red dot on it, but idk if i want to do that or not. It is a few screws, easily restore it back to iron sights. Idk if i want a red dot or not on mine

I have 250 model 99h. My question is how rare are they?

I have same rifle, best groups are always with 87 Sierra's & IMR 4895 although some success with 75 Hornady's & Varget, fairly consistent 1-1/2" groups with lower powered hunting scopes is what I consider excellent results. I have never achieved really good results with anything heavier. That also applies to my Sav's too. Your results shooting also indicate 5 shot groups are too much for that pencil barrel, it throwing last shot virtually every time, 3 shot is way to go. IMHO anyway!

42.00 for that H110. LOT OF$$$.

The 250 savage is inherently accurate. I would check bedding on gun and loose scope setup.

Love the left-eye-dominant gaze

I have one. Since I am in Croatia it was a no brainer since the rifle is made here and if things go sideways parts won't be a problem. Another thing that convinced me was the short stroke piston and the gas setting for suppressors. No mucking about with adjustable gas blocks, buffer tubes or even bolt carriers. Just turn the knob and stick a can on it. I used to have an M&P15 sport 2. Lovely rifle. Sold it after getting this. I'm a minimalist and don't like having too many things to worry about. I do miss the mil spec trigger though. Maybe it's best that I have never shot a nice after market trigger.

Is 16" barrel with 357 enough for a deer rifle?

Ya got to let that thin barrel cool way down. Take your time get off the bipods and sand bag front and back of stock

Did the bullets have gas checks?

U set it on Low or High settings? Thanks

Your issue is the rifle has a wilson barrel which were hit or miss in the rugers as well as the ultralights pencil weight barrel heats up quick, try cutting a small piece of index card and placing it between the barrel and the black fore end tip, this will add a little fore end pressure and help with harmonics, it may help it worked for mine, make sure your action is tightened down into the stock as well, my best luck for accuracy has been 117gr hornady sst or interlock over a max charge of h4350, velocity will be low in comparison to 87gr but still a great 150yd hunting load. Its worth a try for you as its worked for me but all barrels will be different, good luck and hope this might help.

Nice video!.. I'd go a little higher, maybe at least 5' off the ground. I uses landscaping timbers and wrapped aluminum dryer vent around the wood. Also spray Pam or no stick baking spray!...very slippery!

The pipe comes 10 feet long. I cut it down to 5'6", so that with 18" in the ground it is 4 feet tall. This way it is easy to get to in order to refill the feeder. This 4' height has proven to be good from several other feeders like this that we have built over the years. I also did not glue the top to the pipe because experience has shown that over the years the board will deteriorate from the weather and the birds pecking it. If I had glued, it it would be not be possible to take off the top and just replace the board, while reusing the toilet flange and the actual bird feeder. If you have any questions, please comment below. Have a great day and God bless the USA!!

1400 fps with a 158gr bullet out of a 4 inch barrel is pretty impressive. I have a 6" 686 and I've never shot lead bullets out of it, so I may give the blue bullets a try. I also have a Henry .357 rifle with a 20 inch barrel and I'm really curious to see how they will perform in it with that 16.9 gr load. I'm looking for a cartridge load that comes close to maximizing performance in both guns.

Many times when using a light weight barrel l will do 3 shot groups do to barrel heat .

I see you are left eye dominate also, Blues were shooting better for sure .

Adding on from Jesse B!😊😊

With a 158 grain SWC, I like 5.1 Unique & 5.4 Unique for a "+P" load...... March 31, 2024

Scissors are better when opening the ham...and safer

I build and sell AR 10 uppers for hunters who want extreme accurate AR 10 in something other than what the AR 10 is commercially chambered on. I am just now adding the 250 Savage to my AR 10 uppers going to be sold. I use Pac Nor SS super match barrels with all the other parts are from KAK Industries .

There’s something loose on the scope mount, it should be shooting better than that!!!

How sweet. Are you. Getting it ??

how come you can not have the music at thhe front be the same volume as your voice in the video. That load hsdfias is a pain it the kajsffdiasdfd.

Nice vel. 16.9 gr 💥💥