Відео

@@rickstevens2941 thanks

Thanks ...isn is on same location as on video as I don't remember

@@heshamessam8042 that's what I saw in the video The same address I mentioned in my first comment but anyway than you anyway can I use another hex editor ?!

I think there is a way to do that with vediamo (virgin) .. but for me I didn't try as I already have cgdi and abrites long time ago ... but I will test that soon

Thanks

Write to me on WhatsApp +201005387513 ... thanks

That was mk3

@@heshamessam8042 mk3 from uae?

@e-boydtech9080 yes ... but I think they have another branches

Car start with original? ... what do you mean by recognised... ig could be turned on or not or only cranking

@@heshamessam8042 I programmed the key on the bench the smart key and recognized unlocks the steering column the centralization works turns the engine but does not start thank you for your response

I think I must to coding fem on the vehicle but just esys can to do i think?

@yassinemacid9141 and start with original? Or not ? ... while programming fem on bench to process it .. your tool should backup coding firstly and restore and the end ... does it fail on restoration?

@@heshamessam8042 not start with original key!!

Thanks

sorry but if you have any question ask me ... thanks

thanks ... yes it can ... for number 2 and also 3

شكرا جدا...و إياكم

Thanks

Write to me on WhatsApp +201005387513

Yes and need to buy same one ...

Thanks

Yes but I preferred to update and code ... but if only need to get it working so only coding is enough

You are welcome

Thanks

If ended with 255 so it refused the basic settings ... with odis it will show cancellation code which you can use to know the reason why it refused...

@@heshamessam8042thank you!

No it wasn't the same

اه ل حد كبير ... الله يكرمك و تحياتي ليك و كل اهل المغرب

Yes ... don't remember if that was 264kb on that video ... but there is one file to restore ... which is not eeprom nor flash

my ecu ME 2.8.1 AMG ori 264 kb,but when write recovery flash error says,and checksum error,if i reboot k tag and do it again it avcept to writte

@endri15255 OK then you can write them separately... write each ... then write eeprom and mpc separately

@@heshamessam8042 when i save file i see only ori,ori fls,ori epr,now can i writte ori on MPC? because i dont see mpc file when backup

@@heshamessam8042 so ORI can writte to MPC,ORI fls can writte to flash,ORI epr can write to eprom,right?

حبيبي الله يحفظك

Yes ... communicated with it

Sorry.. im referring to the checksum. Or did it not cause problems when flashing to the new tcm

Programmer corrected it ... watch next part of writing

حرب تعمل فلاش ب اوديس انجنير

@@heshamessam8042 ما كتير عندي فكرة عن odis engineer ...بس الفلاش بكون online عال vin و لا بيحتاج file لازم يكون عندي ؟؟؟

خلاص جرب كلون ... و كلمني واتس +201005387513

و عليكم السلام ورحمه الله ....+201005387513 what's app

و عليكم السلام ورحمه الله I didn't try that (removing vtg completely) ... but we may try... but what's your exact problem

@@heshamessam8042 i have surf through your channel and mashallah you deliver good content. I already subscribed to your channel. I'm muhd from Nigeria and i have seen many programming tools which i have been using like the CGDI, CGPro, AT200 for DME cloning, ISTA-P & ISTA-D, E-SYS and NCS expert

@@heshamessam8042 in Nigeria we don't always have genuine bmw parts especially VTG, and its warning light fills up the cluster, the brake, park, ABS, Traction, after installation, programming and coding, it throws a fault 'classification does not match VTG' so if i can find a way to just change the vehicle order nd remove the VTG for good. Right now i have F25 and F01 requiring this very option

@@MuhdAbdul-en4fb I have a video coding vtg ... have a look there ... if you still want to disable ... let me know

@@heshamessam8042 i would try it tomorrow morning inshallah. Hopefully it works. But i would like to learn the vehicle order for future purposes please.

دا نورك ... واتس 01005387513 ... ف المنصوره

Thanks

Tool32

@@user-dg6ed1mj4h on description... link is there

Thanks ... akram

شكرا

Hi how are you ... the key that I programmed to car is not keyless ... but without activation ... car started successfully (proximity) ... then I activated key 5 ... then it worked (the key which is semi smart)... then tried again with proximity key and car didn't start (with proximity key) untill I inserted it and take out then car started with proximity ... something to say ... original proximity key board was too old and there was buttons not working ( also customer said that it sometimes doesn't work correctly

Continue with test plan ... may need online coding ... if yes I think I can connect remotely

@@heshamessam8042 The code is listed in the test plan but when I perform it , it just checked the component then ended the test . I noticed that the module is not listed in the gateway don't know why , shall I try to code it online ???

@mohammedzafer1996 yes it ended a test then it will ask you to perform something as I expect ... will not be listed maybe because its slave module by bcm or at least by the module that shows the fault

@@heshamessam8042 You are right , the idea that the BCM ( electronic central electric ) shows "control module incorrectly coded" code and don't know if this code affect the light issue . Is it safe to code the bcm online ?? hoping I could narrow down the possibilites and make it easier to solve

@mohammedzafer1996 OK that's it ... if you want to double check ... put original back in and scan again ... or if not available just disconnect new one and fault code should change from coding issue to communication issue as I think

Thanks

01005387513

الله يكرمك ... واتس ... +201005387513

OK write to me on WhatsApp ... +201005387513

@@heshamessam8042 I have added your and messaged you. Thanks

Hi how are you ... yes it will work ... but if you replaced the whole transfer case (mechanical and motor) you don't need to write the 4 digits (will be already written)

@@heshamessam8042 I am good, thank you for asking. yes I had the whole transfer case replaced but it was used part. I have downloaded e-sys software now I am going to try it myself. I guess I should re watch the video to see how to do it

@@FaizaAhmedOfficial OK 👍 good luck

+201005387513 ,,, واتساب

مكان حضرتك فين

المنصوره

If all is red (hwel.. swfl.. cafd) means this module is not communicating properly .. fix that first

@@heshamessam8042 how can I do that? It’s all plug in. This only happened after flashing.

@Tayboxer879 all is red... or only one line like cafd for example

@@heshamessam8042 All is red.

@@heshamessam8042 is it possible to revert to whatever I flashed back to the original with FA, ist, soll, and tal?

مش فاهم؟ انا معملتش كلون اصلا

عملت vergin ل الكنترول جديد وًنسخت الكودينق

@@khaledganimi6663 اه بس كدا

شكرا ... مهو د ال عملتو و رفض ... ال انت قلتو انو هو يراجع المواصفات و ال اخترتو ف الاخر بردو نفسو اعتقد

Hello 👋 ... sorry I can't ... write on WhatsApp +201005387513