Відео

No mention of lower drive wheel alignment. It too can cause drift.

Thank you! Wonderful video- it answers so many of my questions.

This is art worthy of the MOMA!! I call it "competence porn" -- a master of the craft doing something so well and producing such a lovely object that I feel privileged to have seen it done.

Love it is it possible to get the plans

سلام .بسیار زیبا بود فقط اره ،کاملا شل بسته شده بود و تاب می خورد ...این درست نیست

I put a square on the table and against the back of the blade. If the blade is 90 degrees to the table, then it’s in the right place on the wheel rim. I found the back-of-the-gullets-on-the-rim-crown doesn’t work for the wider re-saw blades.

1" wide bade, maybe more, and a frickin quarter inch board. You're delusional, you silly boomer.

Don't forget to check that the two wheels are coplanar when you first get your band saw. This is easy before the table is mounted and adjusted. The wheels on my bandsaw were out of plane with each other and had to be realigned. Doing this will make the "drift" problem easier to correct. I used the instructions from Michael Fortune to set my band saw up. Works perfectly with no further adjustments since. I do check for drift each time I change blades. So far, none.

Lovely stuff

Здравствуйте а в какой программе создаёте 3D модели?

Mr Tenta made me sad

Anyone else here been sent by Mr. Tenta

Wow! That is a stunning chair! I'd love to see more still photos of it!

Good sir

Any chance on do a video on adjusting the feed in and out rollers would help a lot of mens sheds out there

Happy new year mr 02/01/2024

Thank you Steve, what a great help especially when it is very expensive to get the exotic wood and you have made it affordable to everyone, thank you. A well known guitar company in their old days they have used Higgins Ink to uniformly stain the ebony fretboards, hope this is helpful to everyone. Thank you. Merry Christmas and happy new year Steve and everyone. ☕️ 🫖 🎄🎉🎄🎉🎄🎉

I've tried this for 4 weeks!!!! Its not working!

thanks but wax melter is better than double boiler

Used it for 60 years --made it myself in a factory with limed de haired cowhides =mass produced ---only problem its NOT WATERPROOF --hence its not used much ----but its very strong --in dry climates!

Looking for reviews and wasn't disappointed here, that's definitely an ozzie accent!

This is clever and I'd think simpler than the Maloof joint but I don't see how it could be stronger. The comparable Maloof joint is keyed on 3 sides, as opposed to these 2 keys, with more glue area than this joint. I think that both this new joint and the Maloof joint are good designs useful on many applications. The Maloof joint has glued surfaces on more planes perpendicular to each other and thus adds to the overall joint strength. I do like your design and your video.

I thought the easiest way was to adjust table to fence and blade!

All I can say is...freaking WOW!! 😲😃🥰

This little band saw has turned out to be the best tool purchase I've ever made ua-cam.com/users/postUgkx5ZrqmYO2uJq_nuU8TopyWxVzn8vqmPUL Once doing the set-up as per the included suggestions, this table top tool has been my go-to saw ever since (8 months as of this review). There are few things I wouldn't attempt with this saw. It takes up much less space than my table saw yet delivers twice as much punch. I've used it to create slices of wood no thicker than an 1/16th of inch by using the POWERTEC BS900RF Rip Fence. For small shop projects this tool can't be beat.

Playing around with this at the moment Steve - so was a great to find this old video of yours.

I see that you have a nice scroll saw in your shop. Why don't you use it rather than the fret saw? I'm just curious as I learned to do this using a scroll saw.

Amazing

Can you purchase this pattern for the horse. Not resale.

Diablo blades aren't made by Bosch!!!!!!!! Freud is an Italian company. not German.

I enjoyed your video where you changed blades every 10 cuts and changed the battery every 20 cuts. Sanding every cut was needed I know. Setting the nails to 2mm is also cute. Slow motion brings it all to perfection. I especially enjoy looking at the bodies of crickets under a microscope.

Thank you very much Ian. I've tried your "recipe" and it does work well. Just one thing, I've made a die for a 16mm rod and my router tends to burn it. Maybe the bit is a bit cheap, or maybe I didn't let the rod in the linseed oil long enough, but do you recommend a special speed for the router to do this job? Thanks again. Aldo, from France

Would be interested to know what you think about the “Little Ripper” video, that basically the main thing that causes the cut not to be straight , is that when you cut close to the fence, the tension released during the cut often makes the cut open up, which pushes against the fence to make it not cut straight. That didn’t come out as clear cut as I hoped . Bloody beer strikes again. He released the blade tension and made a cut, still perfect.

You can also just leave the lid off the vinegar/steel wool jar

So . . . . . . . . . . . . . its not a myth?

Used one, hated it. Over priced, inaccurate. Bed castings were not flat or co planar. Save your money.

Greta review, is the laser beam shooting far on the right side, does that need an adjustment or that is how it should be straight out of the factory?

I want to make the dovetail on the end but the pins in the side100 mlsup

Halo My name is Abdullah from the State of Kuwait I watched the video on your channel and the explanation is good and understandable I have an inquiry. I will buy a band saw, which is almost the same as the specifications of our saw, but its size is between large and medium, because I have a small workshop in my house The question regarding the saw weapon is whether the thick size is better or the thin size is better With work, my most practical thing is to cut the wood with the text, I mean in two halves that The chainsaw to be purchased must be installed, the weapon is open, and its teeth are smooth Note: I am an amateur, not a professional. Thank you I wish you safety and security my regards

Adjust the blade so it is in the centre of the wheel,......yes OK but what part of the blade?,......the front?,....the rear?,..... the middle?,.....the gusset?,.....What part of your blade should be in the middle?

GO BEEMSTER!

Wholesome content

The rando who walked up and stood uncomfortably close the entire process would have freaked me out, lol.

Many thanks! Excellent review!

Very informative video thank you for sharing your knowledge and experience

Great video! I love a project that has a history or good story behind it.

Love it, how CSN I learn this technique?

This is exactly why Japanese craftsmanship will NEVER be rivalled... Mind blowing 🤯

I was wondering about doing this and I am SOOOOO glad I did. My finish came out awesome.

Beautiful work!