Відео

A steel bumper and hitch would be cool

I'm lucky. The original owner had one fitted in factory

perfect

I just used racks. No side bars. You can buy bolts and washers to install them

You could try a set of LR Hurricanes as well, a twin 5 spoke wheel also fitted to Discovery 2's and RR P38's. Same fitting.

Lovely looking wheel those, did a double take when i first saw a Leon with them on 😊

Very informative video but those blue clips have a high failure rate

Any updates??

I have the same relay.. mine makes a clicking sound when in use... Is that normal?

Good clear video; well done and thank you.

Thanks for the vid. I’ve just fitted my tow bar today and am tackling the wiring tomorrow. Great to see where to pick up the wires. My only thing I started doing is I don’t wire the fog I put it to the reverse lights and I’ve reverse lights on my trailers.

Great vid budd,, can u tell me wot size (thikness) was ur permanent live cable was please,, cheers 👍

Any idea how to wire one ov theses to an Audi a5

Hi, your ads have disappeared from done deal, how casn I get in touch?

How did you get the areo bars to fit the rails? Seems fiddly to get them to grab as bolts are too short.

What’s the stud pattern of the mondials? And no issues with centre bore? What mm adapters did you use?

I'm thinking about putting bar work on my caddy. I've got tall tyres on it 195/80r16. They fit with no lift. I need a levelling kit to l I'm thinking about putting a xrox bar up front and an xrox rear bumper. I want to turn it into a four wheel drive. I'll find parts for the rear

very clear. i've been looking for a video like this for ages, thanks for putting it up..

I tried connecting it without the bypass unit and it wasn't working properly. I'm guessing it will not work without this until

Thanks tips ,just got some Mondials for my T4 ,what spacer thickness did you use? Thanks

Good video, straight forward. 👍🏻

The video is very useful as I am doing this exact job now. The only thing I would say is that you should not wire the 12v feed from a wire in the harness. That wire will be fed by its own fuse so there is the danger of overloading the original fuse. If you follow that harness forward you will find a flexible rubber bulkhead seal. Take a long shaft cross head screwdriver and follow the harness. Push the screwdriver past the seal. Open the bonnet and remove the battery. Remove the battery box. Now you should see your screwdriver. Push the feed wire past the screwdriver and remove the screwdriver. Fit the wire to the battery terminal nut (M6). Make sure the fuse is close to the terminal. I tie wrapped mine to the main power cable.

Great vid mate thanks, 👍🏻

what type of wire did you use for the power from front of van to bypass relay,good upload lad

How refreshing to have a nice short to the point video explaining everything you need to know! Good job!!

thanks

Thanks

Thanks you very much

Really helpful video. Thanks for sharing

Can anybody tell me if this works on a 2012 caddy? Would I need anything else done after installing this kit or will it be good to tow a trailer as soon as the wiring is completed. Thanks

what year is your Caddy? Mines a 2016, do I still need to do all this? I don't mind having a go at anything but electrics I hate, great video but still leaves me a little unsure to doing this myself.

Thanks for this mate, its given me some confidence to do it myself..

👍👍

How does the bumper connect to the crash bar? I know it slots onto the mounts on side of van and then screw but what about the rear? Cheers👍

great video, you have helped me doing mine, thank you

So helpful! Hadn't a clue how to do this and was looking for anything to give me some idea for a while. Thanks a lot!

Thanks for the instructions mate. You made a female feel comfortable fitting them. New sub.

Unless you have a towbar, Westfalia in my case, I couldn't even reach all of the bolts, but the plastic bumper was only attached with the 6 torx 25 screws by the wheels, and had been since 2004! It would also be almost impossible to reach the 4x m6 bolts that hold the plastic part, but I managed to attach the new plastic bumper with 2 automotive bolts with a torx had and a flexible socket driver, or whatever you call it.

Do you have Instagram and if so will you message me on it I've a few questions @_mandem_roori_

Really easy to follow, thanks

I'm confused mate with the vr sensor and saw/pip connection. Cloud you please explain how I go about doing it. Megajolt dont send instructions and its ridiculous

Respect brother !

I just subscribed because of this video thanks

Thanks for putting this video up.

Thanks for putting this video up.

Thanks for putting this video up.

Great help this top man

I just like to say thank you for this video it meger help me to fix mine saved me like £40 to fix it

Cheers for that!

How do you clean it afterwards for storing?