Відео

@@b.j.mcdaniel3952 I didnt personally resolve it, but buying the new actuator should’ve resolved it

@@Davest420 thanks brother. Glad it helped ya

@@tr4spyable you’re right. Good thing I said “XK8 in the first 8secs of the video. I was working on an XF within that same week. Hence, the error. Good catch tho 👍🏼

Thanks brother

That was likely due to me attempting to loosen them by clamping on locking pliers and moving it back and forth. He certainly didnt give me impression of someone who beats on the car lol

Piston 1 at top dead center is all you need to focus on. Manually turn over the engine by hand, once you know Piston 1 is at TDC, then you can reposition your distributor etc

Thanks a lot!

🤣🤣🤣🤣🤣

Thanks man. I appreciate the support! Owning beaters has taught me so much.

Thats the goal, short, concise, and to the point 👍🏼 stay safe brother

Its gonna be a year soon since I last had my civic and I miss it. Happy to see everyone else still getting theirs back in order! Be safe!

Hmm, since you replaced the major components of the blower motor assembly I’d move on to get a multimeter and use it on 12V or DC to get a ready of the voltage at the blower motor harness connector, and then at the relay housing. Do this while the car is on and the blower motor is turned to high. You’re looking for the same voltage at both ends of your test. It would be amazing if you could get a test in while the car is on, the blower setting is ON, and nothing is blowing. This will show you exactly where the problem lies cause you shouldnt get a reading at one of the ends of the wiring route. Assuming the blower motor is fine. Thats where’d I’d start. If you recently got the blower motor, save the receipt in case your wiring checks out fine. Those motors can be faulty, especially since its usually OE stuff, not OEM.

There’s a possibility the knob for hot/cold might not be working. But its more common for people to experience a thermostat failure, or heater core issue or the need to bleed their coolant of any air. If you recently did a coolant flush or any work that requires messing with the coolant, I’d suspect thats your problem. The cheapest diagnostic you can do right now is pull off the climate control bezel and inspect the connectors for that knob and the wiring condition. Maybe hit it with air pressure can and try again. Next step i’d check is the thermostat for current and signal with a multimeter. UA-cam how to do that. Lastly, I’d suspect the heater core. But thats the most expensive fix, so do your best to make sure nothing I wrote above is the culprit

Hey man. Happy to have helped you and many more on this great car from the 90s!

Im glad its still helping people out to this day. Its certainly getting too cold to drive around without some proper heating 🤓

Awesome my man! Glad this video helped you out. I wish I still had my civic to post more DIY vids 🥹

Haha. Bro I banged it, slapped it, blew on the connector pins, and still nothing. The module itself was definitely fried.

Hey man, yeah I understand completely. This sounds like your rod and the moving assembly is somehow stuck or jammed when going into the defrost option. I’d disconnect the rod and move it with your hand to the defrost position. If you cant move it by hand, try to further visually inspect the “track” on which the entire assembly moves. It should be free n clear. If its rough to go into the setting, lube it up with a dab of grease along the track and gently work it back n forth. Replacing the module is the next step if you can “manually” get it into place, but the controls wont move it into place after the fact.

You’re welcome! Glad to have been helpful 🤙🏼

Well, at that point it might require some multimeter probing to check for discrepancies in the wiring. I havent gone that deep into the issue but thats my guess

Hey Larry, from the sounds of your description, I would recommend you check your shifter linkage bushings on the underside of the car. In particular, the bushing that bolts up to the chassis just under the shifter. That might be loose or worn. And the smaller springs are responsible for a more ratchet feeling engagement for 2 gears per spring. So one spring does gear 1-2, another 3-4, and the last 5-R. The larger spring makes the shifter’s left-to-right neutral motion stiffer. I wouldnt think it’ll align the shifter to a more centered position. Hope this helps, best of luck!

What problem exactly? The coolant leak?

@@JDL_MobileRepair yeah man tbh tomorrow my gasket maker comes in ima do the exact same. I also had to shave off a 12 wrench but any other tips you have for me this video is great and I much appreciate it man

@@ST1L0KS bro I returned this knock off shit. It kept leaking coolant and causing idle issues. Put an OEM Y8 5spd manifold and felpro gasket. No issues since. I redid this skunk style manifold 3 times with gasket maker. So I just gave up. Plus my throttle body plate kept sticking when the plate closed quick. It’d get caught in the walls of the throttle body

@@ST1L0KS I used a regular 12mm 12pt closed wrench end. Took me a while but it worked fine

@@JDL_MobileRepair so far no idle issues just a small leak thanks for the advice I have y7 but did the swap over

For sure bro. Im just glad you were able to solve your problem. Crazy how something so simple can make us think its a totally different problem 🥸

Makes me glad that my video has helped many. Trust me I did a ton of research as well to no avail. Everyone kept pointing to the Blend Door Actuator, which has nothing to do with the problem many of us experienced

Thanks bro. Hope it solved your issue or gave you some pointers!

Ahh, so the motor might be fine. Its the directional assembly thats seized. Spray it down with WD-40, then add grease or silicone lubricant. It’s unfortunate about your hand, Honda should add one of those bleeding hand warning stickers on that part 🤣

You’re definitely welcome! Thanks for the sub! Hoping to throw out more content for everyone to use and learn from as well! Gotta pass on the knowledge

For sure man! Glad my video helped!

No prob bro 🥹

Happy to give back and help others with this quick fix video!

😂😂😂 sometimes things go south

I mean.. i was happy it happened 😂 Most part replacement videos show the best case scenario. So when something breaks you’re stuck mid repair

Fixed it in 10 minutes. Now I need to get one of these motors.

Awesome bro. I have yet to replace my motor. I left it in place, disconnected, and manually set the defrost setting until summer time and then I’ll just move it to the upper vents lol. Most places want $50 for this used part, no guarantee it’ll work either

@@JDL_MobileRepair Yeah I am going to do the same. I decided not to buy that expensive motor. To heck with the motor, I'll just change it by hand.

Thanks man. Hope you can pass on the knowledge in the future!

I’m your neighbor in NJ. The defrosting part is why I went this length to make sure I posted this video. I dont have a video, but the tiny bulbs that illuminate the climate controls CAN be replaced. They’re extremely hard to find on ebay/amazon cause of the lack of part number. But maybe someone’s parts car might have the bulbs, in case yours went out like all of mine

For sure man. Happy to pass on some knowledge or replacement tips. As of now, I still didn’t replace the motor. Just left it on defrost mode for the winter season haha