- 13
- 5 145
Halfshark
Приєднався 22 гру 2012
Wood-Mizer Accuset 2 explained!
This video will educate you on the features and functions of Wood-Mizers accuset 2 setworks
Переглядів: 31
Відео
Wood-Mizer Hydraulic troubleshooting explained!
Переглядів 35714 днів тому
This video will cover woodmizer hydraulics and troubleshooting along with finishing alignment and Finally get to cut a log after sitting dormant for over a decade!
Wood-Mizer lt40 restoration!
Переглядів 484Місяць тому
This is part 1 of hopefully 2. I'm going through a mill that has been sitting idle for almost a decade. Covering all aspects from the engine, driveline, hydraulics, electrical, and alignment. Hopefully, you can find information here that may help you with your sawmill.
avoid wavy cuts on your Wood-Mizer sawmill with this tip
Переглядів 253Місяць тому
in this video, I address a commonly overlooked issue when trying to figure out why a sawmill cuts wavy lumber. #woodmizer #sawmill #wavey
WOOD-MIZER Lt40, Lt50 Guide Arm Repair
Переглядів 4525 місяців тому
Simple in/out guide arm repair and alignment for loose or damaged guide arm.
Wood-Mizer lt-40, lt-35 side support alignment
Переглядів 6910 місяців тому
Quick video on Wood-Mizer backstand adjustment for square and simple 'how to'. Please leave a comment if you have an idea for another quick Wood-Mizer adjustment related topic. thanks for watching!
Packaging your Wood-Mizer mill for transport Lt-35,40,50
Переглядів 929Рік тому
Packaging your Wood-Mizer mill for transport Lt-35,40,50
Woodmizer lt40 drive belt adjustment - smoking, grabbing at idle
Переглядів 1,6 тис.Рік тому
quick video showing belt adjustment on newer mills that are smoking or dragging the drivebelt at idle. any video ideas or suggestions, please leave a comment. thanks!
fixing bandsaw cracks
Переглядів 2272 роки тому
this video provides a quick overview of fixing cracks in a bandsaw from start to finish. complete process took about an hour and a half. mainly uploaded to show people part of what i do for a living vs explaining it lol.
smoking fresh spring salmon
Переглядів 292 роки тому
a brief video of smoking fresh spring salmon on a rainy Saturday. simple recipe but well worth it!
Manufacturing a bandsaw
Переглядів 432 роки тому
In this video, I wanted to show the process of making a bandsaw the best way i know how. there are more advanced welders for the job but this has been a workhorse for me over the past 10 plus years. I see so many poor welds on bandsaws that cause them to break prematurely that i push myself to make each saw better than the last. Quick overview video but hopefully it's interesting!
Great video. I have the same engine on my LT40. I wonder why Kohler used the fuel shutoff selenoid? Is there some advantage to shut the engine down by cutting fuel vs cutting spark? Or maybe the spark is cut also?
Good one.
Justin from Wood-Mizer here if you ever need help let me know! I work on these things daily!
Thank you.
Rebuilding the lubmizer system. Perhaps you have a video already I'll be sure to watch. New subscriber.
Very informative. Thank you.
Nice tip...Coocks Saws has some good explanation on this also. What if you have a roller the full width of the band? Will it flat it in 1 pass?
@rachianohaselhoef1734 unfortunately no as it is high carbon spring steel and the act of leveling really needs to be concentrated to the highest singular point of the turnover. This saw was very bad needing 3rolls. Most usually need one roll in the center. I have seen a lot of people get great results just using a 3/8 wide roller bearing or preferably a 1/4 inch wide bearing set up in the same way as the stretcher rolls on my bench. Hope this helps
Excellent video for those that need to know how.
Exact problem on my new 12 hr lt50. Been trying to figure out what to do, called WM tech and no one ever mentioned to check this. They suggested soaping the belt. Da Will see if this is my problem.
Thanks for the video. Just bought a 2007 Lt 50 and watching videos to learn about maintenance and trouble shooting. I’ll be saving this video for later if I run into this problem.
Lt50 is an amazing machine! Happy sawing! If you have any problems or questions, or would like a quick video made on a specific issue, message here and I'll do my best to help out!
Owned and sawed with my LT40 super for about 24 years and just learned something on alignment with your movie clip. Thanks for sharing. The woodmizer is a wonderfully engineered piece of equipment. Very durable and easy to work on. My mill still performs very well and turns out precise lumber but I am thinking about trading up for a 50 just for the (I think) better log turning chain turner and I think a little better production speed (I am 74 and need all the help in the speed department I can get)! Still great fun getting out there and breaking out a nice red oak and the grain is always fun to see when you brush off the sawdust.
"PromoSM"
I like your hands ;) what size is your wedding ring?
Thanks for the vid. Fired up my mill this morning to warm up. Went inside for a bit and came out to blue smoke comin' of the mill......................pretty sure the lifespan of the belt was cut in half.
Great explanation I have a used lt 40 that I must move and wanted a walkthrough for that. The mill was brought to me and I have never moved it as I cut in place. Thank you I subscribed.
thank you, just thank you for your time .
actual vital stuff for people to know and they don't watch... I wish you luck in everything you do, cheers!
Thank you that was very helpful. I have this issue on my mill.