Відео

Thanks!

I don't have a cruze handy to look at but pretty sure below the glove box is a plastic trim panel that once removed will allow you to get at blower from underneath dash to drop out. Hth

The scenery and comradery were more than enough, gotta keep it together for kentucky!

I thought it was really good what you got considering the snow and tight branches! Much appreciated! I didn't have anything for that climb for footage so came in Absolutely clutch!

Thanks man! I've always had a less capable vehicle so it's all new to me with this build. Hoping to get out with you guys again soon!

You would have had a blast! Was super fun. I think the f zomb would have been right at home out there. I do believe they are going to try and make it an annual event

@@BustedtoBuilt, I certainly hope they make it an annual event!

@@Captain_Yodelstein we will probably do it again this summer!

Cheers!

In its traditional form, no. You need to separate the hub assembly from the knuckle to do the same job as the tool demonstrated with. If you are having trouble separating the axle shaft from the hub then a puller would assist there

@@BustedtoBuilt Thank you for the clarification. Do you have an alternate method to do the job of the whacker tool? Perhaps carful use of a dead weight hammer? Something jury rigged to attach and allow whacking that is less sophisticated and costly? Currently my traction control and ABS is not working, It's probably the wheel speed sensor, but I doubt my inexpensive scanner has capability for wheel speed sensor. It's frustrating when a low cost part (sensor or wheel bearing hub) requires thousands of dollars of special tools. Thinking of low-cost work arounds, probably one could visually inspect the hub magnet, perhaps ohm out the sensor? What about using one of the cheap hand-held oscilloscopes on the wheel sensor, then spinning the wheel by hand and looking for a pulse from the sensor? One could compare pulses from both front wheels to look for a missing or different signal? I've been wanting one of the low cost hand-held oscilloscopes from Aliexpress or Amazon (about $102 for a decent one, a 40 MHz dual channel Hantek or Owon, but NOT the newest Fnirsi).

I'll be the first to tell you this is a poor video that I was reluctant to put together what little footage I had. Sorry it wasn't what you wanted but this is an overly covered subject if you look anywhere else

If compression is even on all cylinders I wouldn't look too much into that if when running power seems appropriate. As far as the single cylinder misfire I would probably suspect a damaged cam lobe or lifter if everything else is checking out. A cylinder balance test with oscilloscope measuring starter draw is about the best way to confirm without cracking the engine open

@BustedtoBuilt thanks. Took to the dealership for second opinion. Even they couldn't figure it out. Needs engine. They called an ECM (replaced it). Didn't do shit all.

Exactly what I was thinking!

Glad it helped!

Chitter was full..........

@BustedtoBuilt 😅🤣😂

Under the intake manifold

Did not share that symptom

Yep that's the symptom!

Glad you got it figured out and thanks for sharing!

Thinktool pro

Probably a few hundred

I wouldn't roll the dice based off what you see in a youtube video. Check basics like compression and ignition. If you think it's an injector problem there should be sufficient fuel trim data to back that or debunk it or at a minimum take the injectors from 2 and 6 and swap them with known good cylinders and see if the misfire moves to that cylinder.

Usually end up around 1200-1500 depending on the damage incurred and located in brown city MI

You are so kind!

They're 6 inch lift springs for a jeep Cherokee, i can't remember where i got them from but they're not super high quality, cheapest ones i could find kinda deal. Thanks for the comment!

@BustedtoBuilt Right On I Have A 05 2500HD 6.0 4x4 Single Cab Short Bed Conv. I'm Exploring All My Options And Cost Of Doing A SAS.

S/b on a 2500 with a solid axle would be sick!

@BustedtoBuilt Ya It's Pretty Cool Already...Just Need That Damn IFS Gone...Hahaha 🤠

Glad to hear it helped!

Glad to help

Well I wouldn't recommend putting on the small lift to set it up where all the front end components are operating at their limits. If you want more lift get a 4 or 6 inch. You can crank the bars as high as you want......the shock is what will limit ride height

I'm in brown city Michigan

I will pay for your flight to Bristol Ct I have the tools

Flattered by your offer but I've got to much to do right where I'm at. I hope that you are able to get the problem resolved though other means. If you haven't looked into "pine hollow auto diagnostics" I would highly recommend. He is brighter than I and a bit closer to you and I know he will travel also.

You're welcome, glad it helped!

how do u get rid of the traction light and a warning light for stabilizer light or something like that. on the chevy cruze. i regret getting a cruze, its so fragile that car. sensors all over for everything.

ua-cam.com/video/tJp7NArup40/v-deo.html Give this a watch

Very common, hope this video helps

@@BustedtoBuilt this one makes a lot better sense then other videos Ive seen, some videos said its coil spark plug related to the stabilizer light. that didn't make sense to me. ik it couldn't be that.

Nothing off hand probably going to need further investigation

That was fun to watch!

@ I’m glad I didn’t flip it lol

@bschoenbach3614 that was great!🤘🤣 Glad yall had a blast! Your troopers thats for sure, it was cold! Hahaha

@meaganreynolds381, first test of the kart, when I bought it, it was just a frame

@bschoenbach3614 nice work!!

I’m the guy in the monster truck towing the go cart!

@@brycevannote7908 very nice rig!!

Had me laughing so hard! Too good! 😂

You guys put on a show!

@@meaganreynolds381 I’m glad 😌 I always try to put on a good show

@ we would have definitely keep going but shortly after that I hit one of the only trees in the pit and busted the radiator 🫣 but next year we will definitely be back

@MrAaronmicheal5 my husband saw you on a short pushing the BMW and was like oh man that's great haha I said NO WORRIES I got it on camera 🤣🤘

It was a blast, I'm sure you'll have a great video coming out of it too!

@Captain_Yodelstein the walkie talkies made such a fun difference this year too! 🤘💁‍♀️

@meaganreynolds381 , the walkies are a great addition to the wheeling experience. I think the next repair to the ol' F-Zomb50 will be the windshield wipers and washer....lol.