Відео

Have you pushed the tensioner pulley across which will move give you the required room to install the belt? If so are you sure you have the correct belt as ther eare at least 3 different types. HTH

@@trollmanrs yes the tensioner is all the way back and it’s not slack enough to go over the last pulley and I guess so they did it off the reg number but I can’t do it I’ve had enough of today I’ve been trying to do it all day near enough

@@flintsmith154 sounds like you have the wrong belt. Did you crosscheck the part numbers in my video with what you are fitting

@ I had a britpart belt before and that was tight to get on but went on eventually and this new one is a dayco and I’m having no luck with it at all

Thank you, it's called Blu Mediterraneo.

No, not a fan of them TBH.

Hi, have you tried this part number. 50515635

@ thanks! Merry xmas ❤️

@ruu5k4n38 You too, have a good one.

Hi, I purchased the sensors from ebay, but 1 I bought was rubbish and didn't solve my issue. I'll try dig out a link for you.

I just checked and I bought a genuine used one and that worked ok.

Yup easy swap, just make sure the new stalks have the auto wiper feature.

Certainly would, mine is a 2005 Discovery 3 (LR3) V8, so same as yours.

Thanks! I just order a LR4 stalk, will do the upgrade next week. Did you add the auto rain sensor auto wiper option on yours. If so, do you have a guide available.

@@galenyuen The auto wiper option is on my stalk, but you need the sensor which is part of a different rear view mirror which I have purchased. Problem is the mirror is a different fitment to the windscreen, and the actual windscreen is different. My windscreen does have some chips so at some point I will replace it and fit the correct windscreen and then install auto wipers and lights.

Thanks

I think I might have kept one or 2 of the good ones. This truck is now on 168k so it was probably time for some new genuine ones.

Glad you enjoyed it, the editing does take some time, esp as there are a lot of video's in the whole Garage build playlist. This is just a montage of some of those video's. And yes I needed planning permission. 5 years on and it's still looking sweet.

@trollmanrs I ended up watching your montage first and then systematically worked through the playlist! 👌

@@miken688 Nice one, glad to hear.

You are of course correct, but my D2 is a long term keeper which I have already had for nealy 8 years, so rather than keep welding I did the job right.

No sorry I'm not. You can buy the software and cables for not a lot of money, it's a good investment.

Glad it helped you.

In what way ?

Nope all good.

Thanks for the sub!

They don't make it easy !

Hi, sorry I didn't get that far as I bought an exchange head in the head as I was pushed for time. Have a search on line for valve compression tools.

Hello in Thailand and welcome to my channel, Lot of people remove the ACE system due to costs of parts to repair it. IMO it is simply the BEST system on a D2, I can throw my truck into corners and it just stays level, it's amazing. Firstly do you know what the issue is with yours? Due to the age the most common issue is leaking ACE pipes. If this is the case you can cut the pipe where the leak is and fit a 10mm compression joint. If it's the pump of ACE Valave then of course these can be replaced same as the ACE Arms too. Now if you want to replace the whole system you will need to find the standard ARB's (non ACE ARB's) and swap them out. Then remove the ACE pump and fit a smaller (non ACE belt). And lastly to stop the ACE light coming on you will need to tell the computer that you no longer run ACE. Hope that helps.

@@trollmanrs Thank you very much for replying to my message. I think I understand now, and I’ll probably keep the ACE system. I really appreciate it!

I'm using an IID tool as mentioned in the video. It's expensive at around £400 but worth it.

@@trollmanrs Thanks

Thanks, bolt the chassis to the body in all places, and take measurements to check it's square, then weld it all up. Everything went back on pretty easily tbh.

Thanks for the view, so hard to find good royalty music these days !

The shorting of the pins is quite tricky and may take some time. If the app doesn't see the camera it's could because of this. GL

you have 4 subscribers hahaha, and you trying to mentor people? you are a scammer fool

Sorry I do not know why that is. Good luck

...any idea where is the buzzer? Thinking to che k this one as well, but cannot find its location.

​@@mihaistefanescu430try W-40 on each sensor, wait 10 minutes, if the case do it twice.

​@franklinnunez832 sensors are working, but there it's else where the issue . When disconnected on sensor- straight error in the dash, all sensor good, wire good, ecu module swapped the same, gongs level at 5, on Obd reader I can see them working but I cant hear any gongs inside when in Reverse, other gongs can hear. Also I did notice when on Bluetooth module person called can hear me but me I can hear that person.....so no one can understand what's the fault.😢

I have replied via email.

Yes I noticed that it never looks like it's quite fully in, i.e you can see the filter. Is that just a bad design ?

Thanks for the comment

Thanks, this is the camera I bought, price has gone up by a few quid, but I like it as it's adjustable. www.ebay.co.uk/itm/403423405785 I will probably change the head unit at some point as I wand DAB so will get a proper android unit maybe a 10" screen. They seem to be very cheap from China.

I stream all my music from the phone to the radio via Spotify so this one is perfect for me, just need to get it to fit in the whole properly as it's a fraction too small. Thanks for the link for the camera, it comes with a decent length of cable by the description. Tempted to mount on the spare wheel and feed cable through the rear door. ​@@trollmanrs

@@landroverman79 I bought a 1 or 2m extention cable too, just gives you a bit more flexability to run the cable from the rear up to the head unit.

Thanks for the tip.

Hi, yes cap fits the E30 bottle too. Good luck

Hi, its short for Isopropyl Alcohol, just google it there are plenty of sellers including eBay and amazon.

Chassis was about £750, I had already purchased new drop links and Watts linkage. I bought a pr of ARB bushed for under a tenner. Labour cost me a slap up meal in Vegas !

Hi, did you watch part one. There is a link in the description to where I purchased the HID units. The LED strip I got from Ebay I think but the link is no longer working. Just search for switchback LED strip. Hope that helps. M

Thanks, it was a tight timescale due to the MOT being booked the following Friday. Would of been quicker in a garage on a lift, but I didn't have that !!

Hi, No I have the standard reverse lights in the bumper, although I have upgraded to LED bulbs. The lights on top of the roof rack are on a double switch which I can turn on/off from the cab or just inside the rear door.

@@trollmanrs Do the lower bumper lights have a white and yellow LED in the same pod? Or do the standard bumper reverse lights glow yellow, just curious.

@@yes-ps2xq I have installed the amber strobes inside the rear lower bumper lights, so they are serperate. I'm just about to install a new rear strobe system with some better quality LED strobe lights. I'll do a short video so subscribe so you don't miss it.

@@trollmanrs I will be waiting!

Previous owner had used black blocks. !

@@trollmanrs how about trying a magic eraser? Or some type of home cleaning products or something like turpentine.

Hi, you will need to get the codes read i'm afraid.

It's actually blue, the camera doesn't pick it up so well.

On the outside I installed a product called Tyvek, this is a breatherable membrane. Other brands are available but this is probably the most well known brand. Hope that answers your question?

Glad you enjoyed it Martin, and thanks for leaving a commant.

Glad to hear it :-)

yup and you can use the euro flat blades which are miles better. Mine are great now and actually touch the screen.

Hi, yes the aux still works. My B&M never worked, so I removed it and did a proxy alignment to get rid of the "flashing mileage". Then installed this device. If you leave it in it will keep draining your battery. Good luck.

Thanks for the feedback! Appreciate it

I received the Bluetooth unit. My radio unfortunately has a single plastic connector and not x2 clipped together. Are you able to share the name of the adapter or this connector type and I'll see if I can source one here. Many thanks!

@@craiganavi sorry, i'm not sure what they are called.