- 11
- 46 559
smalt1
Приєднався 22 чер 2007
Saab 9-5 Sludge blown Rod bearing
I take a Saab 9-5 engine oil pan off to find debris, sludge and bearing material at bottom of pan. The engine made NO noise at idle and low rpm. At 2200 - 2500rpm a slight rattle would be heard. Almost sounded like a timing chain rattle but I found a bad rod bearing instead.
Переглядів: 528
Відео
WHOOPS , my buddy says no Problem! pulling tree down
Переглядів 926 років тому
Bee expert removes dead olive tree using methods learned in the outback No bees were hurt during filming
Ready to roll - Sonoma raceway-
Переглядів 166 років тому
This is a Lemons 24 hrs race from a 2011 at Somona Raceway. We are team SAABOTAGE driving the black 9000
droping 944 porsche rear end via spring plate
Переглядів 16 тис.6 років тому
Lowering the rear end of my 951 via the slot / slack in the spring plate that attaches to the torsion plate. Final result= almost 1 inch lower.
SAAB SPG at streets of willow CW
Переглядів 36714 років тому
Saab SPG at Streets of Willow CW One Lap chasing a Camero
Ssaaby at the Lemons
Переглядів 1,1 тис.16 років тому
A fun day at the track. 24 hours of Lemons A dreadfully stock SAAB tearing it up. Tracy, CA.
Super Saab 70-130mph
Переглядів 24 тис.16 років тому
Saab Getting Ready for the Track SAAB 900 with a gt3076 turbo, Forged piston, Cam, Intercooler, 3 inch downpipe and exhaust.
What are the wheels? Those are some of the nicest wheels I have seen on a 944 other than Fuchs and D90’s
I have exactly the same rod bearing issue. How did you replace? Where did you order it from ? What’s the name of this part? Thanks!!
Verkaufe 924 porsche turbo Baujahr 1979 5 gang sport Getriebe elektrische Fensterheber und Spiegel beheitz
Tip !! Spray the hell out of the pivot joint with lube !!!!!!😃😃😃😃😃😎😎😎😎😎🍺🍺🍺🍺🍺
Useful video but you spoke too soft and sometimes mumbled...missed a lot of your narrative.
That was painful to watch...
ua-cam.com/video/0AMRpVCeBes/v-deo.html
wrong way to lower 944 rear end, it has to be done by torsion bars. spring plate adjustments are for alignment not for lowering
What size are your wheels?
I was thinking the same thing 🙌
If you loosen the bolts when the car is on jack stands, how do you get it to move to the top? You would think it would drop down.
Jack the arm up separate
wow, that is one dirty engine. A bad Bearing, Bummer. Fix it and get the wagon back on the road
Not bad not bad! I just installed those very trailing arms on my 1956 VW Beetle for an IRS conversion. The additional ability to adjust ride height and adjust the camber are an awesome plus for a lowered car! Check out my vids if you wanna. I gave you a like! :)
niceee man
good god that whistle!
This... Car sounds good though.
this aint not stock isnt it
what car and what mods? this thing is sick.
......LOL. not really
wrong. watch with old classic 900s (i know this is a GM900) when they start off the speedos jump up to 40mph then drop back down. This vid seems genuine. The bit where it revs quickly at 55mph looks like wheelspin. What my 9-5 with only 300hp (and now a blown engine :( ) would do at that very speed with ease.
JÄÄÄÄÄÄÄÄÄÄVLAR!:o
dang you guys were getting some!
i have a saab 900 se 1996... i really like this older model to the newer one...saabs have been around a long time so it seems you have certian guys who are linked to sertian years of the cars..im going to be putting a intercooler and a new turbo and then a new exhaust system..i live in cleveland and i want to make sure when i get on the hiway that power is not a problem...also i LOVE the way the turbo sounds..i want it to sound louder! thanks for the video awesome!
mustangs have pushrods ha ha