Відео

I ordered Sprinco gas rings and swapped them out myself. SOLGW did not hold up to the warranty they claim on their packaging. Gas rings have held up fine since swapped.

Yeah I definitely think I’ll be ordering a second set for my other Howard Leights. They are comfy.

I really like the cheek weld on the B5 systems. Have eyed Vltor. Maybe try one in future 🤔

@itsmillartime6916 I hear you. B5 are OK in my opinion. Just overused like the magnum CTR was back in the day..but the Imod is there to last for the ages. But that's just me. Your build is one I like without a doubt

Thank you 🙏🏻

I blue loctite both sides. Have had them come loose if I don’t loctite. But once loctited no issues. Definitely get bang for the buck safety.

NP Thanks for watching 🙌

So the Upper receivers and Handguards are both made by Zev is my understanding. So solid. The barrels however I’ve heard they use Ballistic Advantage and possibly Rosco as well. I own two SOLGW 11.5” barrels (one with front sight and one without) both of which suppressor alignment works but isn’t as centered as I’d like. Own multiple of their BCGs and while I have had issues with one they didn’t hold up to their lifetime warranty (gas rings that wore out very early) they are still great BCGs. However Brownells and others sell same Microbest carrier with no logo for less. So if you’re looking at their completes there are areas I feel they could improve but I’d still run one. If you are pairing with a SOLGW lower you’ll find the fit is normally pretty good.

​@itsmillartime6916 ya ill just go with a bcm or geissle. Ya I got a couple microbest from arftac I love

Hear great things about those Arftac BCG. Check out a Geissele URG-I. I’ll have update coming soon on my build. Getting my optic and fore grip this weekend.

Thank you 🙌

I haven’t played with a 12.5” yet or a middy. Maybe future project to test one out 🤷🏻‍♂️

Got your IG message. Send on over build pics. I’ve been running an UnbrandedAR AR9 for years and love it. Have their lower parts kits in a few builds and my big complaint would be detents and pins feel super gritty. Recently got a complete factory built AR15 lower from them which looks great but pins/detents are a bit rough. Easy $10 fix for new springs and detents but I’m planning to just run as is for now. My recent go to kit is the SOLGW Semi complete and I snag a Geissele trigger. SOLGW has best feeling takedown and pivot pins imo.

I did unbranded and it didn’t work out when I swapped from a 5.56 upper to 300blk. The BCG (unbranded) wouldn’t load subs into the chamber completely (supers went fine 🤷🏻‍♂️) so I swapped it out for a SOLGW BCG and no issues since. Everything was lubed fine. I’m only buying SOLGW from here on out.

I’ve mainly run UnBrandedAR lower parts (lowers, lower parts kits, AR9 buffer, buffer tube and possibly few other pieces). Also have their mags which are incredible. Highly recommend their mags. Some of the best GI mags I’ve seen. Did you try their BCG on any other uppers? Curious if that was isolated to that upper? Did you try different kinds of subs or one particular brand?

Thank you 🙏🏻 have been kicking around what build to do overview next. May possibly be my URG-I once it is finished up.

I’ve done so much building honestly very curious to buy a complete. Struggle there is not having the customizability of Franken build 😂 I’ve been eyeing Centurion FBI HRT barrel heavily. May snag that in 2025.

Fire build, how's the h2 comparatively to an h1 or standard

12.5” master race 👊

​​⁠Thank you, been awhile but if I recall I started with a carbine buffer and spring. Recoil was heavy with that buffer setup. The H2 and Blue spring made it a smooth shooter. Some suggest H3/Blue or H2/Red running 11.5” suppressed but my thought was if ran it without can the H2/Blue is safer setup for reliability. Didn’t want to over buffer it.

Also running a 12.5" with the BCM MK2 recoil system.

Thank you 🙏🏻

Lubed up with Sotaracha. Recently made a fresh batch 🥰

Just recorded a video tonight with breakdown of this build. I’ll have it posted in next two day.

I’ve been debating a magnifier. Was literally thinking today I don’t think I’ve done an overview on this build. Possibly done one included within another video when adding a part to it. I’ll have to get a video together with a breakdown of this build.

Just finished a video up with overview of what this build is compiled of. Should have it posted in next couple days.

@@itsmillartime6916 awesome thx you won't be disappointed with the g33 the glass on them is very clear it's almost like looking through glass on a medium power optic and it has a very large field of view I like the quick detach mount it comes with too I can just pop it off and toss it in my pack to lighten things up

​​⁠I’ll have to look at snagging one of the magnifiers in 2025. Working on closing out a few projects before tackling the next 😂

They have become my favorite for sure.

All good man. Like I mention in the video I’m just average dude that gets out here and there for classes, range time and camping. If I had to guess I’ve got a bit over 2k to possibly 3k in rounds under this particular Eotech EXP3-0 and additional time on my EXPS on my other BRN180. Rotate through few different setups when I get out. There are areas I’m a little ocd about cleaning my optics hood being one of them lol In person though it’s not a dark as out of the box likely slightly bleached from the sun.

I was curious about the knock off as well. Wanted to support US company so went this route. Holiday sales are decent on them so maybe best time to snag them up.

Update coming soon. Optic and fore grip were acquired but haven’t picked them up just yet. Almost all parts are on hand for lower build out too.

Glad to help out 🙌

Yes the adapter tool comes in the RUM ready for install.

Recharging is going to vary depending on humidity for your area. I’m in a pretty humid area and probably should be recharging on a monthly basis. Horrible with consistency if recharging but do it as often as I can. I also use a small container of damprid as a second layer of moisture collection. Did just recharge the Dehumidier actually last week. Was roughly 72 hours before I’d call it clearly dried out (Purple).

Thank you 🙏🏻

Is this question in regards to RUM mount in particular or Ruggeds mounting system? Haven’t have any issues with my Mirco30 or Razor 7.62 mounts but those cans are not hub compatible. Schedule has been insane so haven’t been able to get out with the Anechoic w/RUM mount. The function of the RUM is same as the mounts fixed to my other two cans I’ve been running for years so don’t foresee any issues. I’ve mounted the Anechoic w/RUM across 2-3 setups and it locks on snug latching over rear of muzzle device so no way it’s going anywhere.

@@itsmillartime6916 The mounting system. Some have said their silencers start to unscrew themselves off. "My razor keeps backing off on multiple mounts. Not a fan of rugged at all. I even use a strap wrench to wrench the fucker down super tight." "My only issue with rugged mount is that if you don't lock it all the way, it can shoot loose the front taper and have a little play." But those were from 2 years ago and might have been user error. I was thinking of switching all of my muzzle devices and silencer hubs to RUM just to make things easier on me.

Thank you for putting out a great product and looking after health while having fun 🙌

Jealous I was hoping to get out over Thanksgiving but wasn’t able to.

When done this will be far from a clone just with a solid upper 😂

UA-cam likes to be able to ding you with enough to remove accounts all at once. I think we will see big changes in social media censorship over the next few years.

Pretty sweet tool

B5 Systems P23 custom stippled by SinnerKustoms

@ thanks

The steiner works no problem with the EXPS 3-0 I have the railscales leaf on my steiner 9007, makes for a nice lower 1/3 cowitness.

No issues. Holo sits above with the EXPS3-0 since lower 1/3 cowitness. Actually just ordered another EXPS3-0 for this URG-I build out too.

Haven’t attempted to swap the rails. That’s a good question though.

I can’t wait. Hope to have optic ordered tomorrow or Tuesday.

Yeah I hear you there. Rather have that slot for my light mount.

Yours is coming. It may not be an RC2 but it’s coming 🤣🤣🤣

Not 100% but people will likely be cloning my build LOL

Approval times are crazy right now. Make you want to order more.

For your use I think the Arisaka is a great option. The 18650 body coming in at only $50 is great starting point build out a solid light. I use a Modlite OKW head which has good throw to reach out to 100 yards or so. For your use you may want to check out Malkov light heads to find something that accommodates closer to Medium range. But also unclear what your medium range is? I spend fair amount of time in woods and fields so being able to light up 100+ yards is handy and light also works in CQB setting. In close quarters though that kind of out put can also splash back a bit. I dragged heels for years before jumping into the weapon mounted light setups so 100% understand your hesitation. My first was a Cloud OWL and from their I jumped into the Cloud Rein series. Reason for doing a Modlite/Arisaka build out for this setup is try something different and because of recently quality concerns I've seen with Cloud. Additionally after getting a Modlite handheld awhile back I now have a collection of heads to support the buildout and different head options for different needs. As far as a guide I have unfortunately not seen one myself. My buildout was based off feedback from buddies I podcast with and others I shoot with. Tailcap if you want a backup switch the Surefire DS00 is the way to go. If you don't care for backup switch or consistent on I'd get the standard Surefire cap. The Arisaka body is cheaper then the Modlite body so a little bit of savings to be had there and sits closer as well. From there it is finding mount to accommodate mounting to your handguard and light head that fits your needs. With Black Friday saves coming up Modlite tends to have some great prices for their holiday sales. Hope that helps a bit. Keep sending questions as you come up with them and I'm glad to help out.

@ that was extremely helpful! Yeah, the part that was really confusing me was the Arisaka light kit is truly a build your own light, which I think is awesome but the amount of options you can choose from I had to write them down so that I can look up each one to see what they are and what they do however once again I do appreciate your feedback.

The options are overwhelming for sure. I had to do the same of writing down the different options and weighing which ultimately fit the needs/wants from this build. After doing this one though I have greater understanding but still much to learn myself.

Sorry not sure I understand your question. Barrel nut is placed over barrel down to barrel extension. Aeroshell 64 grease is used on the threads. It is then tightened up loosened back off then tighten back down to manufacturers torque spec. The backing off is to help season/prep the threads prior to torquing down. Not everyone does that step. Once barrel nut is installed you can slide the handguard over the nut center it and torque the screws to manufactures spec.

Regularly Ultra Manly = RUM 😂

​@@itsmillartime6916seems legit, I approve this message

I should hopefully get to get out shooting next week. Can’t wait to test it out. In my mind I’ve built high expectations of sound reduction🤣

Lock into lower or follower under feed lip?

Dispense and contain freedom seeds.

It’s a solid helmet for sure.