Відео

Este motor puede usarse en California

I watched the video to see how to add the gear oil. You skipped this.

How did this motor last for you? Thinking of buying one

Thanks for making this video, pretty sure I wouldn't have realised it needed gear oil without your video!!

I found this because I was pretty sure when I took mine for its maiden voyage, the gears shouldn't have been literally screaming for oil 😅 great video thanks

You need to run marine gear oil

Waaaayyyy too much gear oil if you see it leaking then you blew out the seal. You’re supposed to fill it right below that line because when liquid gets hot and expands.

Como faço pra comprar uma taser ??? Sou do Brasil

Thanks for the info on the gear oil fill , the cutter pin splits and then bent,and you are 100 on trying to understand their manual 😢😢

I asked an expert he said just petrol because it's four stroke just fuel.

bro knows nothing about tasers

You swear way too much dude 👿👿

What if mine didn't come with that fuel what kind of fuel do I what is is that mixture

Where do I put the gear oil at and the and grease in the top?

I just got a free Hangkai 3.5 hp 2 stroke. I bought a spare prop for $14.. I got to get a pin, the little plastic cup that was in my old prop around the pin, and napa has an exact match stainless cotter pin. The face book hangkai group said use 30:1 for break in, then start using 50:1 after break in. The little 3.5 has a huge following. Not sure about the other Hangkai engines.

Brilliant Video- super intelligent approach and very helpful- thank you and happy boating!

You have to buy a new battery if it runs out of power

damn the happy munches when he chewed that crisp 👌

I know this video was released three years ago, but why did you remove the plate from the driveshaft ? I was told that you remove the uppermost screw and fill through the hole until oils flows back out, it is a level hole.

Nah that ain't Styrofoam you gassy Bubba. Just holler ya farted...

4:23 HAND IN FRONT OF THE CARTRIDGE!!!! You can see it right there! RULE NUMBER ONE!!! TREAT THE TASER LIKE IT IS A FIREARM!!! Don't point the device at anybody, or anything you don't intend to shoot. Don't put body parts in front of the device Unloaded or Loaded. These things are SERIOUS DEVICES!!! They seem to not know what they're doing!

I have this motor. Took it out and it seemed so boggy. I sure didn't break it in for 10 hours though. 30m in the recycle bin, then half throttle on the lake. I see some of you replaced the spark plug. Maybe I should give it another try.

Hi thanks for extra instructions.. can you tell me can one but a new brass bushing and sheer pins . What parts can one get. Possibly need a new o ring seal as well.

Hmmm. Prop not spinning, sheer pin is in…

I know my way around egines. Bought it and after 70 min my gaskets popped. It's a lot of money for 250$. I will not repair this piece of crap with no power at all... Do not buy this outboard!!!

Ive just got one and its starting to smell like rubber butning any help

I couldn’t watch the butchering of the split pin. You had pliers, straighten it ffs. A small hammer would not have bent the pin.

I bought one used with approx 10 -15 hours yesterday and took it on water today and it didnt start after 40 min of running fine. Should I waterboard it for 10 hours now to break it in? Or would be a waste of time. Any suggestions?

great video the 10 hours do you have to do it one go or say 2 hours a day over 5 days?

I think you should split the off the prop pin.

What is that pink oil?

did you use this motor for your sail boat

No the glitter does not match every time to buy a new cartridge they gonna magically know your serial number no

Arlysaiiilprjectodssey

Awesome video! Isn't it possible to do this directly from the boat on the first start? 10 hours straight, 1/4 or 1/3 throttle. Where i live, it's absolutely impossible for me to do it like that in a tub..

When breaking in do I need to just keep it running idle or should I be using throttle also? Plan on doing it in my garden in a bin full of water but wasn't sure if I could just leave it running idle or not :)

I have a 3.6 motor hangkai. In my book it says there is a carburetor oil feeder. Do you know what that is and what is it for

Thanks

Thanks great video

did you have any problems with the impeller? I just fired up my new one just like that but can't get it to pump water

I just got a 3.5 hp and am breaking it in, running it in a trash can w/ water up to the right level. Mixed gas & oil as in your video. There's quite a bit of smoke or burned oil - is that a problem, and what can I do about it? The motor, water, and trash can aren't perfectly level and perpendicular - is that a problem?

I just got a 3.5 hp and am breaking it in, with running it in a trash can w/ water up the the right level. Mixed gas & oil as in your video. There's quite a bit of smoke or burned oil - is that a problem, and what can I do about it? The motor, water, and trash can aren't perfectly level and perpendicular - is that a problem?

You put gear oil where?

ok just to be clear when i got tazerr traineing taqke the the prong thing off if u gonna taze some with out shooting them with tazer

Thank you my friend! Thank you Thank you Thank you!!!!! You just saved my life. I just got one of these motors and had NO CLUE what to do! I found you on UA-cam! You rock my friend! Thanks again & keep doing what you're doing. You're doing a GREAT job! 🇺🇸👊🇺🇸

You aim then you hold it in place then shoot

Does it matter what kind of grease

That's what I said THE F*** !!!!

The safety switch is intentionally reversed from that of an actual firearm so as to make it harder to confuse one with the other.

The safety activation is exact opposite your firearm so that you can distinguish more easily between less than lethal and lethal. Most firearms the safety is up for safe, down for fire. This mechanism on the X26 is done the opposite for exactly that reason.