Відео

Just plug it in an empty spot on your receiver. Just like plugging in a servo.

There is a master switch for the Hydraulic motor. try switching all of the switches on your remote control. Mine came with the switch on the left side of the controller.

@@gijoel5435 So I am able to turn the hydraulic pump on. My switch is on the right. My first issue was not knowing if there was fluid in the reservoir because I could not see it. Today I filled it, but nothing is happening still. Before I try it again, I have to clean the fluid off of it because it was a mess. I can hear the servos opening the valves inside, but nothing is happening. Do I have to run the pump for a long time to get air out of the lines maybe? I'm not sure.

So you have to open the body plate with 4 allen screw on the right side. The one that looks like a Jigsaw panel with the notch in between. You can open just the front or both. That is here the reservoir is located. Its a see through container that you can see how much fluid inside. If this is full and your servos are moving when you try to move the arm and nothing is happening, look at the screen on the inside of the Cab. Check the reading on the pressure gauge, it should jump between 1 to about 4 value. I not you may need to reverse your #5 channel on your radio because the fluid is flowing backward. Also before you do these test keep the original sealed screw cap on the reservoir because of the backflow will over flow from your reservoir tank. For my excavator, I did not even use the breeder plug for that reason and it is working just fine and not have to worry about leaking especially when you tip it side ways..

@@gijoel5435 I have to work the next few days, but I will definitely try this. Thankyou for the suggestion and I will be back with an update.

@@gijoel5435 Alright, I'm back to work on the excavator and I have unchanged results. The pressure on the screen in the cab doesn't go above 1 MPa when the pump motor is on full speed. This was after the bleeder screw was replaced with the old one. The level of oil in the reservoir is a little more than 1/4 inch below the top. I've downloaded the manual for the radio and will try to figure out how to reverse the channel for the pump.

G.T.POWER E30 BT Container Truck Light Voice Vibration Simulated System+ESC H7W3

Vielen Dank

@@holgergumm2594 Gerne geschehen

You will love it. Here's a link to the sound and light module I used on it. usa.banggood.com/1-Set-G_T_Power-Container-Truck-APP-Control-Lighting-and-Voice-Vibration-System-PRO-for-Rc-Car-Parts-p-1426662.html?gmcCountry=US&currency=USD&cur_warehouse=CN&createTmp=1&ad_id=513001116163&gclid=CjwKCAjw9e6SBhB2EiwA5myr9jZ3aIvci_nJw8bqgp7FgWL4nrsdR3xbf88a8SstQjJrMjuNLLR_CBoC5NgQAvD_BwE

he took mine too

I will do it when my new Radio and receiver arrives. Since I have to replaced the receiver to change into the new radio transmitter. Stay tuned.

I got this from Ali Express. Here the link. www.aliexpress.com/item/4000076289315.html?spm=a2g0o.detail.1000060.3.bbdf62cbpiZka4&gps-id=pcDetailBottomMoreThisSeller&scm=1007.13339.169870.0&scm_id=1007.13339.169870.0&scm-url=1007.13339.169870.0&pvid=3e5e932f-ac87-4f3f-94a2-acfae53b0855&_t=gps-id:pcDetailBottomMoreThisSeller,scm-url:1007.13339.169870.0,pvid:3e5e932f-ac87-4f3f-94a2-acfae53b0855,tpp_buckets:668%230%23131923%2348_668%23808%233772%23958_668%23888%233325%238_668%232846%238112%23541_668%232717%237558%23119_668%231000022185%231000066058%230_668%233468%2315617%23892

www.amazon.com/dp/B08XB8ZM3F?psc=1&ref=ppx_yo2_dt_b_product_details

www.amazon.com/dp/B08VDNT3WJ?psc=1&ref=ppx_yo2_dt_b_product_details

www.amazon.com/dp/B089DJ7237?psc=1&ref=ppx_yo2_dt_b_product_details

Hello, here is the link to the sound module and the wiring diagram. If you have the original programing on your radio for the Hydraulic pump ESC you need to reprogram it so it will register for the actions on your excavator arms. www.aliexpress.com/item/1005003372704802.html?spm=a2g0o.order_list.0.0.21ef1802qmF7ns

I do. I can send it to you.

drive.google.com/file/d/1vUZELVToeAq_H_UYi24A7CArZ4_DlnR-/view?spm=a2g0s.imconversation.0.0.1d093e5fuLXHhK&usp=sharing

@@gijoel5435 thank you so much

Sure I am waiting for the Y radio harness so I can install the light control. When I do I'll videotape it.

I one use 2S with 4000mh lipo. I used a lipo monitor for the voltage drop.

I'm using 3S, 2200mah Lipo battery. I normally set the timer at 5 minutes with last 30 second warning where I prepare to land the plane.