Відео

Camera view too far out

What if the rotor doesn't wanna come off the bearing hub and there's no screw holding them together?

Angle the plow

How does it angle?

Thanks buddy helps me save money did it my self in a snow storm

I didn't know that's how you do the last light in the back way easier than I did it😂😂 I pulled the liner and everything

Thanks for the vid

A bit risky since the ATV is only supported by single cable. Why not leave it in neutral and let it sit on it's butt. Dealers store them that way.

Clearly demonstrated, excellent presentation. Well done, and thanks!

Excellent DIY video. Thank you for posting.

Hows it ride with chain do you feel them maken ride rough

Do you still have this sled?

I've heard of springs going through brick wall after coming out the spring compressor , be careful. Lift kit ebay link doesn't work.

Ok

Dude this vid saved me hours on my install. Thanks for taking the time to lay it all out and walking us thru the entire installation. Thanks you

Just my two cents. I removed the tank and replaced the pump, but based on comments by others I expect to have to do it again in the future so I only reattached the tank by the two top screws which secures it just fine. Secondly, I find the washer nozzle itself to be a poor design. When I get it adjusted for the drivers side the other half just shoots washer fluid out into space. I've ordered two individual automotive hooded sprayers, one for each side along with the appropriate tubing and diverter connector to the second sprayer. There's plenty of room under the hood on the passenger side to drill out and install the second nozzle. This should be far superior to the cheap factory set up.

Besides not unhooking the battery good advice . Straight to the point

Is she holding a baby the entire time or am I tripping lol

Dirt bike

what is the wrap gives you, is it to reduce the heat ?

What size and type is the stud?

Unhook your battery 🤷🏼‍♀️ js 🤣🤣🤣

Is it powerful enough to run a kitchen stove?

Did you experience any rubbing after this? I have 28” bear claw HTR on my 2022 outlander max but still get some rub after trimming.

Keep several copies of the recipe when you buy because they know it’s under warranty but without the receipt you’re fk by this brand Just so you know 😢

I would of just bump started it

Hmmm, the Canuckian method that avoids disconnecting the black fascia at the bottom for easier acess to the winch drum - eh?

Is that a factory winch on the can am ?

Thanks for the extra tip’s

Noticed the lights on the back of the cab. Do you have a video on the install of those? Love them

Hello, Are you interested in testing our products? We would like to invite you to test the UTV Flag Mount/Whip Light Mount for your 2019 POLARIS RANGER XP1000

How do you like the hmf? Did you need a fuel tuner?

Thanks! Just popped mine open and saw we ordered the wrong light ! I see in the comments the type I need.

I have one of these and it starts after 20-ish kicks, I love working my legs tho so meh

Like the bloopers!

Oh my... Something about having a nice, organized, and clean garage that make the ATV look even better.

When you said yada yada it made me think of the Jerry Seinfeld episode 😂

What would cause a polaris canvas door lock to kind of pop open a little while driving? Is there a way to adjust?

O wanna know. If the fit. 2018 outlander 650

Thank you so much for sharing this video. Based on what I have seen in other videos for this SUV and trucks, the metal bushings on the bracket get "tighten" to the alternator during installation of the corresponding long bolts. Thus, when replacing it for a new alternator, they have to be "retracted," just like you did, gently tapping on them to push them out, so the new alternator can slide in, and then when you torque them, they will be in the right place again. Thank you for the very straight forward instructions. Some videos recommend disconnecting the positive lead of the battery before doing this procedure as precautionary step.

Great job next time let us know the tools used to do the job

Will it run a mig welder at 220 volts ?

Pulisci il carburatore ,cambia candela

you need a new one .chupa😂

THANK YOU

Sorry. What you're calling a D-ring is a shackle.

So your driving on the shackles?

Thanks man yes that was easy. I did mine 1 year ago. If your a MAN please do it yourself.. save your money. Get off the couch!!! 😂😂😂

What about the pin to connect the sled to the snowmobile, is it supposed to have a shock reducing spring built into it? I see some online with a spring and some don't have one. Can a simple bolt act as a pin?

Do you have to let it sit at all for the loc tight or just assemble and go