Відео

Não presta ! Não aguenta mais que 2 semanas em uso normal . Lixo

Per quanto costano le batterie non so quanto possa convenire.... Saluti

Hello. I wanted to know if this device could be connected to a 12v 2-pin fan. And another thing, I want to use it so that the fan starts when the temperature rises below a certain value, and stops when the temperature drops below a certain value. Can that be done with this device? Thank you.

Cell 1 Cell 2 Cell 3 +-----+ +-----+ +-----+ | | | | | | | + |-------| + |-------| + |------- B+ | | | | | | | |-------| |-------| |------- B3 | - | | - | | - |------- B2 +-----+ +-----+ +-----+ | | | | | | B- B1 B2

Your video is extremely helpful and very detailed, thanks for taking the time to make this 🙂

BEWARE of using parkside batteries on other tools, all 20v parkside tools have a bms and cell balancing, BUT it does not test or prevent over discharge, if you over discharge a parkside battery, the protection chip in the battery will lock out the battery forever! it will not send 'handshake' to charger anymore. its a safety feature of the bms IC to protect us from fire, not to increase company profit.. also recharging each cell will not unlock it, I have tried many parkside boards etc as I built a full 50mph+ e-motorcycle from parkside cells.

А как заряжать кальциевые акб там нужно 16 в

Can I use this device to drive a 12 V 8 A motor from a 48 V solar panel ?

Thank you so much. So simple, direct explanation!

Hi! I recently had to hit this problem with my Lux Tools. Did you find how C terminal exchange information? I wanted to use Makita Batteries and found a "work around" at the moment. I sacrificed an original battery to use the BMS. I emulated tensions of every single cell with a custom circuit (using OpAmp). With this solution I have my custom battery conversion kit, but I still want to decode that C signal.

Здравствуйте а каким током она заряжает? Просто хочу ей акумулятор для электровелосипеда заряжать

Watched two videos on same module, but same content. What about short circuit and reverse polarity protection..??

What about short circuit and reverse polarity protection..? Please..

Tengo varios walkies y el TGuv2 plus, es el que mejor recibe y el que mejor mantiene la señal. Con diferencia, es el mejor que he probado en cuanto a recepción. Y he tenido incluso un yaesu FT1 " que me costó 389€ ". Pero el TGuv2 plus, es mejor!

La recepción del TGuv2 plus, es mucho mejor. Y si cambias la antena, por una Retevis 701, mejor que mejor😉👍 Gracias por la prueba! 👌

Țiganie!

The high power Superheterodyne version now has a USB charging socket.

nice

Hot glue for casing? Nice Idea!

Hello, I plan to make a power supply using the AC-DC2416 with a 36 volt output and place the XL4016 at the output. Have you made that configuration?

بالنسبة للمقاومة المتغيرة نا الفرق بين ccو cv

Very nice and clear presentation, thank you!

Cuál es entonces la mejor antena para el TGuv2 plus?. Dime algo por favor 🙏

Дякую. Корисний пристрій. Треба бути придбати.

specs say IGBTs too; does it test IGBTs? tkx

preciso esquema t7 obrigado

great review i make my choice now

after struggling for about two hours I found your video, thank you so much!

Great video! that keeps on giving even 3 years later ! I'm looking for similar device but one that functions from 20 c not 30c. Wonder if something like that is out there?

@powerbatterychannel4315 Good evening everyone, can you tell me which resistor to buy, send me a site, and then you can't see where the resistor is soldered, take a closer photo thank you very much

Thanks for video

❤

Thanks very much, i searched for the Value of the middle pins to run parkside Performance tools at 5 cells. With only positive and negative,the tools dont run,show error. Thank you

Hi Mine is now showing Zender. And the symbol and it doesn't work at all. What is wrong with it? Cheers 🍻

Muchas gracias!. Me has ayudado mucho con lo de encontrar el offset. No daba con él, jajaja!. Una tremenda máquina muy buena este TG uv2 plus. Me encanta!. Le he puesto una Retevis 701 y va fenomenal!. Una recepción muy buena !. 😍👌

Very helpful review. Thank you!

My T7 stumps the CPU freezes on some semiconductors requiring disassembly to reset by disconnecting the battery. Wonder of the unmarked CPU is a fake.

I bought this years ago never calibrated it as it did not come with any of the bits you have but is seems to work fine :)

is it possible to update the firmware ...! thanks for your reply we are interested in buying a pair

when I charge it after 1 or 2 seconds it was cut off. why?? How can I fix it

Does the volatge output change when input voltage changes. Im planning to use such circuit for cctv from a 24v battery bank powered by solar. When battery voltage drops as its being used will the 12v i set for the system also start going down?

Doesn’t measure gain ?

Great video

Cordless tools especially brushless are best

I have a t7h and can’t get it to go into calibration mode, even got a replacement and same problem

Там стоит полевик без радиатора. Не потянет он ни хрена, а вот пристроить его на хороший радиатор (коробка позволяет) - тогда будем посмотреть

📌 *Здравствуйте. Если на плате выставить верхний порог 14.4, а нижний 10.5 Вопрос: она включит зарядное устройство, если появился свет, а на аккумуляторе в это время заряд где-то по середине, например 13 вольт* ❓🤔

This device was useless to me until I found your video. Thank you.

Is Borat doing the review? 😂

Thank you wery much, this was extreamly healpfull, good job and good vide