- 59
- 153 279
SoCal.hondabuild
Приєднався 22 лис 2019
Rebuilding local Honda dirt bikes that were inoperable
1987 CR250 Build Video
1987 CR250 Build Video
Music in this Video:
Artist: Tycho
Album: Awake
Song: Awake
Year: 2014
Music in this Video:
Artist: Tycho
Album: Awake
Song: Awake
Year: 2014
Переглядів: 3 333
Відео
1987 CR250 Build Comprehensive Video
Переглядів 1,4 тис.Рік тому
Video showing a 1987 CR250 Rebuild. Bought this bike for $900 not running and show here how I rebuilt the engine and restored it. Music in this video: Artist: Tycho Album: Awake Song: Awake Year: 2014
Mounting Dual Exhaust on a 2004 CRF250 build
Переглядів 4,4 тис.2 роки тому
Mounting dual exhaust on a 2004 CRF250 build using a 2006 subframe and 2006 y mount I got off eBay. You will want to mount the exhaust to the y by welding or use radiator hose with heavy duty clamps if you cannot weld. Music in this video: Artist: Ben Howard Song: Black flies Album: Every Kingdom Year: 2011
Shimming and Adjusting valves on a CRF450
Переглядів 3,5 тис.2 роки тому
Show how to properly shim and adjust valves on a 2002 CRF450 to get the gaps between the cam and valves within spec (0.09-0.15 mm Intake) and (0.25-0.31 mm Exhaust gap). Bike started and ran great after changing out valves to stainless steel valves from titanium which are more durable but require heavier springs.
CRF450 Bike Build Modernizing an older CRF450 I sold to the Langston’s
Переглядів 1,1 тис.2 роки тому
Modernizing and rebuilding a 2002 CRF450 that I sold to Grant Langston and his Father Gerald out at Glen Helen. Music in this video: Artist: Tycho Song: Awake Album: Awake Year: 2014
TX Race Plastics Kit on a 2004 CRF250 Build
Переглядів 1,9 тис.2 роки тому
TX Race Plastics Kit on a 2004 CRF250 Build
TX Race Plastics Kit on a 2004 CRF250 Build
Переглядів 21 тис.2 роки тому
TX Race Plastics Kit on a 2004 CRF250 Build
Installing a digital hour meter/tach onto a CRF450
Переглядів 8412 роки тому
Installing a digital hour meter/tach onto a CRF450
Installing an hour meter/tach onto a CRF450
Переглядів 8262 роки тому
Installing an hour meter/tach onto a CRF450
Replacing a broken Shifter Bracket on a 2018 Can Am Outlander to a Aluminum billet bracket
Переглядів 1,6 тис.3 роки тому
Replacing a broken Shifter Bracket on a 2018 Can Am Outlander to a Aluminum billet bracket
Comprehensive instructional video on making mounts to mount modern plastics on an older CRF450
Переглядів 2,7 тис.3 роки тому
Comprehensive instructional video on making mounts to mount modern plastics on an older CRF450
Diagnostics on a CRF450 that won’t start, summary of fuel and Carburetor operation and diagnostics
Переглядів 11 тис.3 роки тому
Diagnostics on a CRF450 that won’t start, summary of fuel and Carburetor operation and diagnostics
Installing Titanium Valves in a CRF450
Переглядів 4,9 тис.3 роки тому
Installing Titanium Valves in a CRF450
1990 KX250 Bike Build Comprehensive Video
Переглядів 1,9 тис.3 роки тому
1990 KX250 Bike Build Comprehensive Video
KX250 Bike Build building the rear wheels
Переглядів 523 роки тому
KX250 Bike Build building the rear wheels
KX250 Bike Build Suspension rear shock rebuild
Переглядів 1,4 тис.3 роки тому
KX250 Bike Build Suspension rear shock rebuild
KX250 Bike Build DUBYA Wheel facility tour
Переглядів 2503 роки тому
KX250 Bike Build DUBYA Wheel facility tour
Reassembly of the bottom end of the CRF450 engine
Переглядів 2993 роки тому
Reassembly of the bottom end of the CRF450 engine
CRF450 fork disassembly and servicing changing the bushings and seals
Переглядів 683 роки тому
CRF450 fork disassembly and servicing changing the bushings and seals
CRF 450 Engine rebuild video Bottom End Dissassembly
Переглядів 4,9 тис.3 роки тому
CRF 450 Engine rebuild video Bottom End Dissassembly
2004 CRF 250 Restored bike at Fox Raceway in Pala
Переглядів 1284 роки тому
2004 CRF 250 Restored bike at Fox Raceway in Pala
Nice bike bro I got the same bike just not as pretty
You know where I can get a inner outer side case for this exact year bike
Love the old school look. Dope
Nice bile
*bike
Nice bile
I would really appreciate your input, I have a 2004 Honda crf450r it only runs when you push start it or if you squirt fuel into the intake, it backfires when you kick it over. I cleaned the carb and everything so I’m not sure what to try next, thanks!
Have a look at the head, shim the valves, inspected the valves and seats. Go ahead and pull the head off and take it in to have it inspected. Have a look at this video
@@Megabiggie ua-cam.com/video/x06PWJxcNMM/v-deo.htmlsi=DUEBYDd0ox-eDqW5
@@socal.hondabuild8349 appreciate it, I took of the head, put it at top dead center, and it turns out who ever put the cam in last put it backwards 🤦🏽♂️
@@socal.hondabuild8349 all I had to do was spin the can around, bikes than flawless now, starts first kick 👍
So clean
That turned out sick
I had a no start problem with a 03 CRF450R and rebuilding the carb and checking the valves revealed the problem. The valves were too tight and I went down the to smallest shim I had to get ,006 clearance and the carb was old and the gaskets were bad and jets were clogged. That and a quick oil change after a quick ride got a lot of black oil out of it. Runs pretty well now. 5 kicks maybe to start it up?
No 2017 radiator shrouds that I have seen have that top mounting hole where's yours is located.
Hello my name is dom and I'm getting ready to put duel exhaust on my 05 crf250 I have the y pip and a 06 head pip I know I will need the 06 air box and subframe is the any thing else I will need to get thanks
Super simpler explanation thank you
Wild bike man great job
The temu akraprovic!
will a 2021 plastic kit fit a 2009?
Do I have to weld the adapter on I have the 150cc version of this bike will the 36mm clamp on or do I have to weld it ?
Hi. I have a 90 KX 250. I want to rebuild the bike and engine but where do I get ALL of the parts needed to fully refresh the engine?
anywhere online
I did that yesterday on my 2023 outlander, it wasn’t broken but just to prevent that to happen. Got it from eBay. Great vid buddy! 👍🏻
I have a 2006 crf 250x I want to put 2017 plastics on and do away with the front head light and rear fender, will these templates work with it
Sure they should work
If you make them you may have to adjust the holes a bit depending on how the plastics line up.
Can someone send me the template for the CRF 450 2007?
only vid i’ve seen that actually walks you through it 👍👍
Looks awesome. I dont like old brittle scratched crap 😊
Where is your other exhaust? I thought those had two exhausts?
Hey great video! I just bought one of these bikes and saw you had a new looking bottom end in a bag, where did you get it from? I can’t find any online for my 90 kx250
It is a HotRods crank for a ‘91 be prepared to take a grinder and shave some of the rod if it comes in contact with the engine case. It may be best just to have your current crank rebuilt by CrankWorks in Az
If you do buy a new crank make sure and freeze it overnight then heat the bearings so that it slides into the crank bearings, always recommend replacing the crank bearings while you are in there as well!
How much would this be worth?
a lot of money since they dont make em anymore (the 2strokes) 5k+ at least
a lot of money since they dont make them anymore at least 5k+ but if you can you should get 500 2stroke buddy 100%
@@mizmac8180 have a 97 banshee, 88 250r, 87 250r and a lt500 quadzilla.
Man i need help bad. I have a 04 crf450r. Runs great when it starts. But ive been chasing this hard start issue all over. Did valve clearances plug carb clean and coil. Nothing has helped. When i kick it will pop with each kick like it wants to fire but just isnt happening at the right time. I checked timing so many times i lost count. I even went couple teeth forward and back and its always the same situation. I need some guidance please.
Have you rebuilt your head? Replaced your valves and recut your seats? I would take it to a mechanic that can rebuild your head and cut the seats, popping and not starting is not a carb issue, likely the head. Take it off and to a local dealership and have it inspected 👌
Would they been the same dimensions for the 2008 model to use same plastics as you have here
Similar, you can always get some metal and line up the holes
ua-cam.com/users/shorts2S-zjjl6VhM
10/10 Where can I find this kit ? Is it available for the o3 450r ?
Lemme buy some brackets brotha 🙏🏼
What kind of bracket would I need for an 09 crf 450r b I’ll buy one
No coupler connecting the middle exhaust?
I did not put it on for this shot
too bad they don’t make the kit for my 08 anymore or i would have that put on it. been looking for months for a good restyle kit and that had been the only one i had found previously 😢
2007 crf250r where do i order from
I have a question would really appreciate you input & help. I have a 2006 Honda 450R the carburetor in your video is identical. The Honda sat for about 2 years with the same fuel. I drained and refilled with fresh fuel. My quad would start only if adding some fuel in the intake run with mid to high throttle and shut down at an idle. I ordered a rebuild kit on amazon. Dis assembled cleaned all ports. Replaced true jets and seals supplied in the rebuild kit. After reinstalling the carb my Honda would not start. Not even with fuel sprayed in the intake. I ordered a replacement carb on line had the same results. I’m very surprised it will not even start for a moment. My next plan off attack is to check if the valves are too tight. Do you have any advise as too why i may have starting issues after rebuilding & replacing the carburetor?
Yes your valves would be a good place to start, when they wear they stay open from a tight or no gap with the cam. Take your head off and take it to a mechanic, have your valve seats replaced and recut and replace the valves with stainless steel they will last longer. If it won’t start this is certainly the issue, the bike absolutely will not start if the valves are wore and hanging open allowing air into the intake and preventing it from starting even if you added gas and fire from the plug. Hope this helps
@@socal.hondabuild8349 appreciate your reply. I did a compression test & have 40 psi max. That’s seems low, do you happen to know the compression specs?
@@Playersclub415 I do not, I would go ahead and pull the head and have a look at the valves, I’m pretty sure with the age that’s the likely case, if you flip the head over and clean the carbon with ether you’ll see the gaps between the valves and seats quickly
You are also going to want to disassemble the entire carb including the mid-body, that needs to be cleaned as well, it can get completely full of gunk
where did you source the gold rims
They are Pro Wheels, based out of Oregon, they can build and anodize whatever you want. Excel also sells them
My bike makes the same high pitch ticking sound it’s weird but always runs fine so whatever I guess lol
I was doing my valves and my chain came off the gear on the bottom I didn’t know this till I tried to crank it. Once in figured out what happened i lined all the timing marks up and the bike won’t start it’s super hard to kick too
You may have bent a valve if the marks weren’t lined up and the stress popped the chain off, the tensioner may not be tight either, I recommend taking it to a mechanic to have a look
If the valves are bent it will be difficult to kick
@@socal.hondabuild8349 okay well I have to pull the head anyway the threads stripped
Is there anyway i can het the templates via email? Also kudos on using metric system
Sure send an email to SoCal.HondaBuild.com@gmail.com
How did you install those mufflers
Check out this video showing the install ua-cam.com/video/t4QHqfYBY3U/v-deo.html
With the brackets this kit comes with will other colored plastics fit as long as there the same year 2019?
💯💯💯
wat company makes those plastics
They are Honda OEM plastics from 2017, I made brackets to mount them on an older CRF
Check out this video on how I did it ua-cam.com/users/shortsnjWSVUIHACY?feature=share
Comprehensive step by step ua-cam.com/video/RRuR5IAeKXQ/v-deo.html
Hello. good job I have a question When you install the valves don't you put some increase on the valve? It's just putting the new valves in and that's it?
You should replace the valve seats and have them machined, steel valves you should lap to get good contact, titanium valves you do not lap, but again make sure and replace the seats, your valves will run longer and last without having to be shimmed….hope that helps!
Would this be the same carb as an 05 crf450x?
Yes very similar FCR carb, the book will outline any differences between years which are minor from 02-08….I would recommend getting the Clymers Manual for your year
Can you show a video at the pipe side? I have a Vittacci Cougar Sport. The muffler went bad. It has a three hole flange on the pipe side. How do you retro fit this muffler to that three hole flange??
Nice man
Beautiful Build my friend 👏🏽 Do you manufacture brackets for an 08 CRF 250 in order to update the plastics? 🙏🏽
Hey did you buy regular plastic set or the already converted plastics
It’s a TX Race Kit that comes with brackets to mount regular OEM plastics
Feel free to check out other videos on this page teaching you how to make your own mounts for OEM plastics
ua-cam.com/video/RRuR5IAeKXQ/v-deo.html
@@socal.hondabuild8349not available