Відео

Can’t wait to hear how the track day was🎉🎉

Nice job.. Just one little tip.. test bulbs before you replace cover, just incase they don’t work for some reason! Saves taking cover back off. 👍

Hi, what gauge jumper cable do you recommend? Also, how long does the wire have to be? I would like to do this repair but am not sure what gauge of wire to use. Thank you.

Awesome!

I also have a wideband o2 sensor on my car with dual Weber 40s. What sort of air fuel ratios are you shooting for at idle, cruise and wide open throttle? They definitely seem to be happiest in the mid to low 12s from my experience . That would be very rich on an efi but I guess not for carburetors

So u r that guy putting silly putty down when u lay pipe? Wtf is that stuff?

Hi Hans, thanks for the clear video. I had to change the main turn signal light but followed all the same steps (including the quarter turn to lock the bulb into place). However, once I plugged everything back in, the entire headlamp no longer turns on. I’ve checked all the bulbs, the fuse box (all three) and made sure the bulbs were all secured… Any ideas what I might have done or am missing? Thanks in advance for your help!

So posting a video where you're just wrenching at fast speed. Not saying what you're munching on what size bolts, what order and which dividend is totally useless! What a waste of time 10 minutes

that's motivating :D i'm building a b230ft right now and bought a dark red 940 without an engine! Greetings from austria!

Good result. Handbrake is probably partial seizure of parking brake shoe expander inside the parking brake drum. If you have an oil leak, hope it is not the sump gasket. If it is, you may as well have the front subframe powder-coated when it is off. I didn't lower my 940. I fitted Bilstein B6 and plan to finish with extra bracing rather than lowering.

I think that some of the dust comes in along the bottom edge of the rear doors. This would come from the front tires throwing it back as you drive. The mud guards you installed will keep dirt from getting in along the back edge of the door. I have ordered these guards and will be installing them soon for my xc60

Only Saab would engineer a brake system like this and like no other, totally unique! Think they were aliens, homoSaabians!

Thanks for the great Volvo content Hans! I love the 142s, not too many of them but they will always be my favourite.

Should I swap the gray CAP that my xar was fitted with to a green CAP, the old one is set to around 0.65 bar and the green one is set to around 1,5 bar

what year is the xc70

I mean... I love volvo but this should have been on from factory... stupid

great footage

The toe is displayed in minutes and not degrees. I also just found out that that exists. There are online cakculators dor that

i like chrome exhaust pipe

Favorite is a tough choice. The Bertone was great and setup really well. But seeing the 142s, 480s and 240s were equally awesome. The sounds as the cars flew down the straightaway were the clincher. Such great sounds!🎉🎉🎉 Thanks for sharing Hans.

I have outrunned BMWs Cossies that had twice the amount of power than my 9 series volvos. Volvo4Life

They test the shocks and springs in Finland??

So the difference between 92 hp and 116 hp is cam, head porting, and valve size?

Yooo mä oon finlandist

How are the bearing going? I used a cheap bearing and regretted it within a year. Only use genuine named brands like Fag, or you will be doing this job again within 2 years.

Me first 😊😊😊😊😊😊😊

Great revue, they are out of stock at the moment in Australia but I will get one as soon as they have them again.

Thanks Hans, seems like a good purchase for evety workshop

I loved the zoom close up of the moon,,,,🤣🤣

U push the stick to the left and up there u have it

hi, can you sell the aircon? :D

Awesome. Thanks for the video, a massive help.

I didn't see you put a thermostat back in hopefully you done it out of camera.

😎

It's good to know that it finally works properly, I have mine a little disassembled because one of the bolts on the thermostat housing broke and I couldn't get it out. and i have to replace some old burned hoses and the faulty temp sensor

Hello! Very good work!

My 940 b230fk has had a developing problem of the car just shutting down when idle or when pressing clutch when coming to a stop. No resistance or anything, just dies completely and then often times starts up but sometimes it does not start up at all, it will only start again after you hear the fuel bump buzzing. I have replaced fuel filter and checked for leaks, both good. Gonna replace relay next, hopefully it fixes it.

overfill. You have to have it in the middle of the glass

Are your tektro brakes m275?

Hi Hans. Have you adjusted the ac compressor belt tension? If you could please make a video. Regards Anders

Hi Han Did you not have to bleed the brakes from the rear calipers after fitting? Thanks

Mine has this message, but lights are levelling up, but active bending function is not working !! Is this the same fix !!

Great review, you are very nice and clear! Thank you!

Many people apparently don't know that Led Lights permanently damage the eyes of both humans and animals, take care. Thanks for The Video. 💖

Awesome video love the content! Cant wait to watch the cam change!

You need to bing more vaucuim from the engine to help you press the pedal brake

Лучшая охлаждающая жидкость это вода. Но не для северных, стран 😅

I just did this job on my 2002 S80. I just wacked the old hubs/bearings with a heavy hammer and they all came out like that, no press, no special tool needed. Yes I am in countries with snow and salt: Switzerland and The Netherlands and Northern France. I guess the XC70 is different than the S80.

Great work! I checked all your hard work!! I do have exactly same problem.. I checked all your step, result is same😂 also, I checked all wires resistance connector to connector it is 0.2ohm all, which is okay now a I am guessing swapping ecu or ezk… wish me luck! Im with you!

Great video!! Helped a lot! I have 95 940 exactly same symptom.. wish I could solve.. I followed all procedures no luck): I really dont know where to check..