Відео

Thanks for commenting on my stuff. Can you please refrain from putting nasty comments on my videos from now on? Please and thank you.

Look like same instructions as far as internal bolt removal applies to Rouge 2008

11 QUARTS??

So when you take the pan off, is going to leak the 11 quarts cvt fluid you put in at the end? just making sure so i start to order the fluid.

Hey, I have a 2012 altima and after a while when accelerating it will barely go up when i floor it and when I brake to 0 mph and try to accelerate again it doesn’t go past like 5 mph and barely reaches 1.5k rpm I don’t know if i have the same issue but it seems similar

very good video but camera guy or girl not good

I have a 2009 Nissan Altima. I was driving lost all acceleration in drive and reverse. I did some research and from what I have read is that it could be the mass air flow sensor. I watched a video that said to unclip it while the car is running and if it stays running the sensor is bad and that's what happened when I did it. Dods that sound right? Im sorry I don't know anything about cars. I lost my husband to cancer and I don't have money to take it to a shop.

What did you use to clean the pan?

I have same code Nissan quest 2013 looking for mechanic

followed the steps, easy enought. car changes gear but it will not shift at all. did i miss something or i might have a bad step motor. will need to go back down to recheck everything. any suggestions will help.

Just got my 2009 Nissan Altima and it got up to 80 on the highway and completely stopped accelerating

I noticed that the old stepper motor arm is a bit more extended than the new one. Does that matter? Thanks

Having these same issues with 2007 altima 2.5 s 277k miles, but it's not showing any codes. I've replaced both speed sensors on the transmission and the problem persists. Without the codes present, should I still try to replace the stepper motor and see if that helps or would you assume it is something else causing this issue?

Thank you for the step motor info.

Step motor?

You sure got the extra like from me thumbs up 👍. Please what do I do if there's no acceleration at all ?

2:53 ‘it just feels dogshit’ 😂😂

you seem like a big enough guy where holding your shoulder wasn't necessary, but I guess if they don't know your skill level fair enough

very helpful...tyvm

Where did you purchase the stepper motor?

Wow just saw 11 qrt waaa I know this procedure works but Nissan recommended 5 to 6 is max guess it's a typo

Nice job

So just watched this and was literally the best , then I look and see no more videos , 😢 is there a different channel??

i did everything step by step and all gears were drive. i got back in and realigned the little lever thing and now all gears are neutral. i got back in AGAIN and swapped to the old step motor and i still have no gears. its throwing p1777 after changing it out and it was p1778 before changing. i dont know what to do

I saw many internet posts about E36 coupe and sedan side mirror are different, do you need to modify the M3 mirror ?

I replaced the step motor same shit, says a solenoid is bad also didn't fix the problem

When cleaning do you just spray the oil off with water?

Ordered mine off amazon did urs come with oil residue on it? Or is mine used?

So I have a 2011 Nissan Altima with 210K. Somewhere after 90K it started to do that (not going fast even with high RPM's especially in weather under 60 degrees F). I saw a blog and someone stated to simply warm it up for 1 minute or so, then shut it off, count to 30 seconds, then start it back up and drive. It worked. I just hated that I could never just turn it on and drive lol. But now that I see this video I think I may be changing that step motor soon. Thank you so much for posting.

My ratio control valve gets stuck doesn’t go in and out smoothly, the part that goes on to the stepped motor. The part that looks like a “T” could you give me some advice on how to fix that? Pls

Thank you

Dont you clean the connections with maf flow censor cause they are full of oil because they sit inside the transmission and disconnecting might cause some oil to leak inside the plugs??

This guy needs a donation from everyone taking this info it saved everyone thousands of dollars

Spent $550.00 to have this stepper motor replaced in my daughters 2012 Nissan Altima with 158,000 miles on it…Essentially flushed that $550 🦌’s down the 🚽 as the repair didnt fix her POS CVT transmission!! Intermittently comes & goes, specially when on a hill! Any body have any other ideas besides replacing the transmission ($5-$6k) ?!? 😡

What MM size is the hexagon L wrench?

Opened my first shop in 1977 (not trying to give away my age LOL) Wonderful no nonsense presentation. Great explanations & helpful tips. ChrisFix has nothing on you.

Thank you for the diagram…I needed to know what bolts come out thank you sooo much

Once you fixed the step motor did it instantly start working or did it have to run a while before it acted normal?

Bro it's the transmission my 2008 altima have too

Awesome good job thanks to show and explain

Help, please! I followed the steps in the video, but now the car will not move fwd or back when I shift to reverse or drive. I did notice that on the video the rod was all the way in out next to the little lever with the 14mm bolt but on my car is wa all the way in.

This video saved me SOOOO much money! Replaced the whole valve body for around 300, every garage was around 4k with labour. Thanks for this awesome video man!

I have codes for pressure control solenoid & torque converter clutch solenoid.. this will pretty much be the same job right? Will I need to worry about the Allen wrench thing replacing those? Any tips much appreciated

My 2009 Altima is doing the same thing but no codes. Was your car throwing codes, check engine light on?

Do you have to reprogram the transmission after replacing the stepper motor?

Good come to Alabama and help me please

I've been working on cars my whole life I'm 37. Great video! Awesome angles and a thorough explanation! I now know what's wrong with my mom's car and can get it taken care of!

Did you use brake fluid cleaner to clean those boats off and what did you use to clean the pan?

What is the part number from nissan for this piece for 2.5 4-cylinder?

can you tell me what code or symptoms you were having.????