Відео

Very helpful video. Thanks for taking the time and effort to make and post it.

not vertical? good luck w that one

The constant throat clearing was super annoying.

5th build, 5th time watching. Thanks! :)

This was GREAT! Thank you for taking the time to make this video. It helps those with no experience at building in this platform.

Hey man, I’ve been looking online and haven’t been able to find a solid answer. Can you confirm this is a Low shelf lower? Sweet gun dude

Thanks for the quick refresh.

You said to be aware of the gas block and then installed it directly over the block.

I couldn't get through this once you got to the trigger. your bandage is blocking the shot. not editing out your errors. not holding up the part so we can see our looks like yours does. maybe this video would be useful later on when I get to a different part

What color is your gun?That Beast is awesome looking

What did you do for the stock? I can't get mine on just like you. I had trouble

Negative!! You do not use the spacer on aluminum rail. That spacer is used on polymer handgaurd. Much lower profile without it so remove it..

Now I am not going to watch you, find someone else, you cheated the process

You need to show how to put the gold pin in, not show the outcome

That a fine legal line

Not gonna lie I felt dumb. I was stressing over it because I didn't want my spring to fly out again and lose my peg like i did before. But this seems super easy. Can't wait till mine comes in the mail.

A chisel? Or punch

Use Knipex pliers for the bolt catch pin and the trigger guard. Wrap the jaws with tape first.

Razor blade trick worked well for me. Didn’t lose any take down pin springs. Thanks

Nice, simple and straightforward, thanks !

Horrible

Just put one on my AR yesterday. It went on fine, didn't need the plate. I need the angled hand stop.

What a steal!

What are those bands called for wire retention on the light ??

Just a couple of tips. When installing the bolt catch, put the spring in first and then the little tip. The tip should be touching the bolt catch lever, not the spring. Also, use some sort of slave pin (small punch or allen wrench) to hold the bolt catch lever while tapping in the roll pin. As you tap in the roll pin it will push out the slave pin. I always use some wide painter's tape along the side of the receiver to prevent marring while driving the roll pin in.

Why does this video exist? Learn how to build a lower first, then build some lowers, then post a video "teaching" others to build lowers. Then you can actually show people how you build the lower, instead of constant errors and editing over the important parts.

Really great kit! So far my trigger guard roll pin and my bolt catch roll pin are too large for the holes. It’s a Ruger lower so it’s not a cheap no-name lower. What crap!

did you have to purchase the stripped lower seperately?

Nice too bad im in WA

"ok this part is difficult, so I'm not going to show you how I did it" tips for your next How To video: break it up into steps, and watch each step of your video to make sure it is passable, before recording the next step

You might want to brush up on how you install these before you do an installation video. On a handguard like yours, you put it on as 3 individual pieces. You don't use the long plate.

Good tutorial 💪

Now I know how your thumb got sliced up. Using a razor blade to hold the detent. It slipped.

1/8" punch Razore blade Blue tape Armorer's wrench Hammer Are those the only tools you used for this?

Very good video. It is a big help for doing it the first time.

Watching these videos make me realize how us men really love going through holes in every aspects of life. 😁

I found it was easier to pound the rollpin in to the first part, aligning it with your fingers until its stable/hammered in just before the space for the bolt catch, and then put the bolt catch and finish hammering.

Thank you for sharing this video! I was able to complete my build after watching your tutorial.

Wow... practice several times b4 making an instruction video.

Instead of hammering the pin I used pliers to squeeze it in

Thanks for the tutorial.

So hard to follow

Appreciate you making this video for us newbies that haven’t done this yet.

I literally just bought these things and need to build. Will be the first time is there a list of tools and sizes of punches needed somewhere

​@pistolpete2731 I'm new to the AR platform but I watched a different video and this one seems clunky. I know there are rules to follow and they change depending on the year. I watched one from american viking that was everything i needed to know. I appreciate this guys time and effort I did watch the whole video. Im always looking for new techniques to make things easier for me just my .02

Magpul furniture sold by psa as lower parts kits are universal for all lower receivers just fyi......trash.

UA-cam removed all my videos like this and demonetized all my videos.

You point out that there is a large end of the spring when assembling the trigger parts but never show or say which end goes in first. Please add this in comments.

Good attempt, but too much off camera work.

Great no BS build video Sir. Bare bones with no special tools other than the armorers wrench. I am a First time builder with No experience with AR's what so ever and it only took me an hour to do this build and I couldn't be happier. FYI: I used a shish kabob skewer to push threw to hold the detents in place instead of a punch and it was a perfect fit. Thanks again 👍