Tips for everyone, firstly the top panel clips will break pretty much 90% of the time and if you just pull the bumper from the fender retainer it'll break so you have to take the retainer off from the back side of the fender which it's not hard to do just 3 small screws
I'll save everybody some time, here's the video: Mumble mumble mumble, camera shaking around aiming at random places like the garage floor while he's mumbling about parts of the vehicle. Repeat.
Need to quit jerkin the camera around. I threw up twice before I realized you don't know what your doing!! thankfully I did not break the clip that holds the lower bumper to the upper body panel near each tire.
Hi, would you have any pictures of the back of the bumper? I just ordered the chrome tow hooks for my 2015 Yukon Denali and I ordered the new molding with the tow hook cut outs. I was hoping to see a video or pictures on how that molding comes off. It appears you don't need to remove the entire bumper to exchange the tow hook molding. Thanks for any help.
My clips that attach the bumper near the tire broke right off when I went to pull away. No idea why they would do that vs unclipping. Now I'm screwed and will need to replace the molding they clip into.
This video helped me out. Thanks! One tip for others, to reach the two bolts down at the bottom behind the grill I used a magnetic nut driver it on an 8" flexible drive shaft attached to a socket driver (screwdriver handle with square female end that takes bits, adapters etc). There was no way I could get my arm down far enough behind the grill to reach those two bolts any other way. Then for replacement the magnetic bit holds the bolt so you can drive it back in. Good luck!
Thanks, saved me alot with this
Thank you. You are the GOAT
Tips for everyone, firstly the top panel clips will break pretty much 90% of the time and if you just pull the bumper from the fender retainer it'll break so you have to take the retainer off from the back side of the fender which it's not hard to do just 3 small screws
thanks,wondering where that piece was.
What size fuse
I just turn mine on with this method
Thank you
Terrible Video.. Moving too fast and terrible lighting under the car.
The one video I need to watch on you tube and I can't her it ... lol Still give you an A for effort
can’t hear a damn thing delete this.
Worst camera angles evwr tho
So you made a jumper wire. Your lucky their was a fuse if not your ecu would be fried most likely an maybe worse smh
What’s that fuse called ???
Multi fuse block Dealer part number 38231-TZ3-A01
What’s the part called
Multi fuse block Dealer part number 38231-TZ3-A01
What’s the fuse called
Multi fuse block Dealer part number 38231-TZ3-A01
BATMAN APPROVED..... #nailed it.
I'll save everybody some time, here's the video: Mumble mumble mumble, camera shaking around aiming at random places like the garage floor while he's mumbling about parts of the vehicle. Repeat.
I've never seen a more useless video in my life. Maybe try aiming the camera at the things you're talking about? Just a thought.
I’ve never heard a more quiet video in my life
Thank you, it happened that I ran into the same issue.
Video is trash man fix your volume
Need to quit jerkin the camera around. I threw up twice before I realized you don't know what your doing!! thankfully I did not break the clip that holds the lower bumper to the upper body panel near each tire.
Tard! Why not take bumper off to show
Hi, would you have any pictures of the back of the bumper? I just ordered the chrome tow hooks for my 2015 Yukon Denali and I ordered the new molding with the tow hook cut outs. I was hoping to see a video or pictures on how that molding comes off. It appears you don't need to remove the entire bumper to exchange the tow hook molding. Thanks for any help.
Idk if you'll see this but i also drive a 2006 S60R and I'm wondering where you got the caps for the headlight wipers?
Do you know if its the same procedure on a 2015 yukon xl? One of my headlight led halo not working and i wanted to fix it.
Did u ever fix it?
My clips that attach the bumper near the tire broke right off when I went to pull away. No idea why they would do that vs unclipping. Now I'm screwed and will need to replace the molding they clip into.
This video made me dizzy lol
This video helped me out. Thanks! One tip for others, to reach the two bolts down at the bottom behind the grill I used a magnetic nut driver it on an 8" flexible drive shaft attached to a socket driver (screwdriver handle with square female end that takes bits, adapters etc). There was no way I could get my arm down far enough behind the grill to reach those two bolts any other way. Then for replacement the magnetic bit holds the bolt so you can drive it back in. Good luck!