Відео

useless video. i dont wanna even see your fingers

תודה על הסרטון ממש עזר להחליף את שלי שנשברו

You're the best

Only video i could find on this specific repair, even though it has to be one of the most COMMON! issues.

Thanks you!!!! save me!

אח שלי אין עליך תודה רבה

i just threw it in the trash. whoever designed this can go to hell. waste of time. a good headset but a total waste when it comes to parts. design is very stupid.

Super hard to tell what you were doing but after awile i figured it out thanks for the help!

you placed the tabs wrong, ua-cam.com/video/CASX-C0SNpI/v-deo.html this is the correct way

mine just broke into pieces are they sell it?

How dowloading your efects???

where i can buy?

Been here, did that too. You put those bullsh** plastic parts upside-down. This tiny dongle should go to the bottom, while curves aligns with the chassis. If swapped it still do its job, but it's way harder to assemble the cover. TBH - the design of these covers is absolute dogsh**. It cracks over time, you have to glue it, and it's hell to assemble it back. Clearly designed to make it un-repairable.

THANK YOU

Holy fuck. The tabs should be placed the other way. I tried your method so many times. Going insane over here

Thank you so mutch, you is my hero!!!

To anyone who opened their headset, only for these two little pieces of shit to pop out, and then watched this guy fumble around for 20 minutes, most of it off-camera. The correct way they need to go in: Sloped edge toward the inside of the headset (screw side of the plastic cover) and following the slope of the plastic piece. The little plastic lip needs to point toward the ear cup and rest in the gap for the headband going towards the ear cup. I recommend first putting the plastic pieces in the covers and testing to make sure the covers go together perfectly with no force required before proceeding to fit it to the headband to ensure you have them oriented correctly. It's easy to break the plastic covers if you try to force it together or tighten the screws when it's not properly assembled.

doing it right now... design from hell... my hands hurt... but thanks for showing how...

I’m literally dying I’ve spent two hours trying to put it back, but for some reason it won’t close properly as if there was something that inhibits its tight closing If I dont make it tomorrow I’m jumping from the roof

Malísimo!!! no lo hagan, así no es!!

Thank you! Finally a tutorial where I can actually see the pieces and not the person's fingers 😂

Recently cleaned my headset and those 2 tabs came out so was confuse on where they're supposed to be placed. Thanks for this!

the plastic tabs are in the wrong position

Lol Just Shove it back in and Use 1 Dollor roll of Duct tape Your done

The god

The tabs need to be inserted 180 degrees to how you did them. So the slope matches the curve of the piece, and the little notches face outwards towards the meta earcup holder. I just opened one side, forgot which way, then checked the other side to confirm. Also if anyone found they got slimey/waxey from the velvet finish going off, I just cleaned these with pure alcohol and a toothbrush, which works fine. You do loose the markings though.

As a 13 year old I don't have the skills to put it back together i spent a hour already doing this I gave up I'm buying a new one

i need that plastic cover where can i get one

Thank you so much , i bought logitech pro x cushions + headband for my hyperx cloud core i didnt know you need to soder to remove the handband so when i decided to put it back i couldnt it took me over 1h until i found your vid it really saved me from madness , (4th time putting it back and still its not perfect like the other side) the side i didnt remove

some help me out where can i buy that plastic part

Thank you so much! It's almost impossible to put the plastic back on. Terrible design

Yeah.. That shitty plastic cover design is the pain in the ass. Super glue to the rescue :D

thank you!!! It confused me a long time!

I took apart the top to make it easier on myself to change the cover, the little plastic pieces came together whenever I took apart the cover. Should I snap the plastic piece in half?

What is the flight time with this motor and battery?

אני גם מטיס שם

משוגע.... :) איפה הטסתם?

יש לי טריינר כזה לבן

It is too big...notice he's got an adapter plate between the motor and the mount, to get the motor further up...

It's not mine, So I don't know :)

And they told me a 12 inch prop was to big ;) Where are you located? Interesting skyline. Max flite time?

hi there, can u tell me what is the brand name of your cardinal cessna?

very smooth!

Very nice :)