Відео

8:55 I think that is a transient voltage suppressor, TVS. Thanks for the video and your findings Tobi !

Standby is 2 amps at 13.4V, About 27Watts. at 15 hours that is 405Wh/ 13.3V (adjusted) that is 30AH. 12V is the Nominal.

Is it possible to have dual boot so you could boot Venus os or another pi operating system of the same card.

FYI when using a torque wrench with crows foot, the crows foot should be at 90 degrees. The way you had it 180 degrees actually applies more torque and may be why the crows foot bent some

Thank you for the tests.

Great Job Thx

@tobisreallifeskillswithtobi How much height did the roof rack added? This is one of the roof rack systems that I'm currently eying on.

For 230 euro is very good

Thanks Tobi, good to see this test!

Used your example and was able to get a working cable first try connecting Vistron MPPT to Raspberry Pi 4 running Venus. Thanks!

Any update on victron gui v2 on RPi with non victron displays? I’m rocking beta 3.50 and it still seems non functional on my 4b and a 10” display.

Is there any protection between the cells? As the housing of the cells is connected with negative connection. If it's just the thin blue plastic in between, I would never have dared to use the battery

Great vid thanks for sharing your tests, I was thinking of buying one of these. Can I suggest you turn off autofocus when you have the battery on the bench? It keeps focusing on your hands/arms and back again. It would be good to see the brand of cell to get an idea of lifetime as well. Thanks!

Just had this delivered. Can't wait to use it. Mine came with a floor and drain tube too.

What's the purpose ot this device if you can't integrate it to Victron Cerbo GX?

They are the same company as Eco Worthy. This is Eco Worthy step brother but they are essentially identical.

I had my 2020 JLU aluminum steering box changed out to the steel one under the Jeep TSB. It made a significant difference in the overall tightness of the stearing. I never had death wobble...yet, but steering was overall a bit loose. Highly recommend getting the steel one.

I just received the same battery! So far impressed, but confused on the float voltage? 53.84v as per the 100% state?

I tried the update but had to revert. I'm still on 3.00 and when I go to 3.41 setup helper, shutdown, gpio, and temp sensor need an update to work. When I try to update I get an error or it says no file set for this version

puedes traducirlo al español

Mind doing one on a cell phone 📲 battery too? Thank you kind sir

When I had problems like this, I set it to auto update. And after some time it was updated.

You used the wrong screws for the wing nuts/quick release.

Unsure if there's been a change but mine updated first attempt. Maybe the digital gods were smiling down on me XD

Not available on their website or amazon. Price not listed on either site.

It says temperature control, but doesn't have one. Money back! Liars!

Tried to order the 300Ah battery, but the only options available sre the 280Ah?

Another great video. Thanks. My jk bms has a build in thermal protection and also external. Maybe the manufacture is referring to the built in one in there manual?

I have a Jeep Wrangler JLU 2019 I did the same process you did but the dealer said that I need a 9 quartz but it’s already full when it came to 5 - 6 quartz I tried to refill it more but it won’t let me refill the rest of my transmission fluid. It will just overflow. I did the cycle also but still

#4 wire doesn’t do 200A as the battery states the BMS can handle?

Thanks for the teardown Tobi 👍

Are the installs of the overlays specific to your screen or is it required for all screens? I have the raspberry pi screen v1.1 so I don't know if I need it or not. the resolution on mine is 800 x 480.

How do you get the top off it so cleanly, without mangling, or destroying it?

Thanks for the video Tobi!

Very interesting. On the app screen there is a spot that says active balance on the bottom in the middle. Not sure what it does, but maybe you have choices to set it on there or see what it is doing.

Excelkent

Nice, surprised you got it to trigger with ice pack!

Oh great I’ll purchase it Thanks so much for the 411 !

Just a note for viewers : Jst connectors come in different variations with colors not the same as what is described here. Important to note is the two outside wires run straight, parallel which should actually be red and black. Meanwhile the two center wires which are the TX and RX criss-cross.

Very nice thanks!

Correct me if I'm wrong but wouldn't it be simpler to describe it as the two outer wires run parallel or remain the same but the two inner wires criss--cross. done! GRD - GRD TXO -RXO RXO -TXO POS -POS

Thanks for the video. I just purchased 4 of these for really cheap. I wondered about the quality but it seems OK. I'm not worried about low temp because I live in California and it rarely gets below 32°. These will be in series and paralleled with a series set of Watt Cycle 100ah.

Dose anyone know what's happening with the GUI V2? Is there a plan for it to work on the RPi screen as at the moment from what I can tell it'll only work in a browser?

Thank you! I could not have installed setup helper without you. Putty did the trick! I spent days trying to get the PI 4 to work properly. Finally new SD cards came today and the old SD card was corrupt. Now I just need to figure out how to install devices. My monitor is in my living room and all my solar stuff is at the other end of my RV. VE cable will be very hard to reach. I originally thought it would work off of bluetooth but guess not. Any suggestions?

any support to get it working on rasberry pi 5

Hi, The last couple of updates i have done lost settings and apps like package manager, etc. Are there any tips on making updates more reliable? Also, how is it best to back it up before doing an update? Great videos they have made it so easy to setup my own Pi.

How about inbuilt BMS battery balancer? Someone said its 30mah only and proper one must be installed in it.

Is it possible to combine the bluetooth version with one without bluetooth e.g. in an 2P configuration? Would the app show the correct values?

Thanks for the video . Good to see they haven’t changed the batteries since I opened mine up. LiTime is consistent!

Thanks for this test! I just bought 8 of these for an upcoming battery storage solution. Looking to buy two 48V 3000VA Victron Multiplus II GX's. The batteries obviously can't communicate with the Victron through the CAN bus, but Victron themselves state on their website that it's not strictly required. DC House provide the Voltage to SOC mappings to be configured. The batteries are cheap now on Amazon. You can go even cheaper with a DIY battery, but for me that's an absolute no-go. I have no risk appetite for all the hassle I'm seeing people get into, with all the cell imbalances going on etc. These batteries to me seem to be the perfect option in a tight package.