Відео

@@cobratok740 this product has been discontinued.

@@franklinmerrique6912 please contact orders@springerprecision.com as they can best assist you. We have a lot of options. Thank you!

@@jack.simmons please contact orders@springerprecsion.com if the product page doesn’t have enough information and they will assist you. Thanks

We supply an Allen Wrench with the extensions. You can contact orders@springerprecision.com and they can help you with the size needed fro your part.

@@nerdino639 yes, they use the standard tubes.

@@antoni0_o_ please contact orders@springerprecision.com and they can assist you. Thanks!

It should work with any equal to or lager than the factory well.

We will not be doing trigger jobs. Thanks.

Please contact orders@springerprecision.com and they can assist you.

Their website says no. But I asked if it would be close enough to get it on there with a bit of willpower. We will wait and see if they get back to me.

It does not fit the P01 as shipped.

​@@tedmales6984 It does not fit the P01 as shipped. It may require extensive modification that requires skill and tools.

@@donberg1791 we make the shorty version for 9mm only because many people use weak loads.

@@SpringerPrecision what would you recommend for this gun then please? i think a compensator on a 9 is kinda silly but...

@@donberg1791 You would need to get a Barsto .45 barrel that we can thread for a comp and use our XDM 45/10mm comp

@@donberg1791 shop.springerprecision.com/xdm-10mm-open-compensator/

so that comp will work with a Barsto barrel even tho the gun is not an XDM (Its an XD Service) Correct? if so then yes that's what I'm going to order next. I just received my Barsto 9mm barrel from you today

Excellent!

@@jameswilliams1280 yes. There is a hole in the slide stop the pin goes through.

@@SpringerPrecision thank you so much for the fast response. It’s greatly appreciated. I love your products.

@@az_pit_viper4270 if they are closed at the muzzle, you may need to make modifications. There are several companies that make compensator compatible holsters.

@@brandonrootsaert1213 you do not want to install the factory retaining plate. It will serve no use. Thanks.

This model only works on the full sized models.

The grips can’t go below the frame and need screws long enough to catch the mag brake.

The grips need to be above the bottom of the grip and the screws need to be long enough to catch the mag brake.

@SpringerPrecision they are flush fit just like the factory grips are.. when u say "above the bottom" do mean no overhang or do u literally mean short?

@@WettDoggTV they can be flush but not below. The well sits flush on the bottom of the frame.

@@JohnAIDoe try using the shaft of a Qtip to hold it into place before trying to get the pin in.

It does not fit the P01

There is some variance in the grips that we discovered. If you contact our customer support, they can assist you. orders@springerprecision.com Thank you.

Legion M17

I think it would require beveling of the plastic on the spacer to seat inside the magwell.

Yes

@SpringerPrecision - Thanks, I look forward to doing business with the company

@@MrKells503 you should get a customer service response on Tuesday or Wednesday with the holiday. Typically, there are two sets of screws, on for the plate to the slide and the other the optic to the plate. They should be labeled so you make sure they fit before attempting to mount the plate.

@@SpringerPrecision the plate and slide holes share the same screws for the 407k and only the 2 screws in the kit

@@MrKells503 so you have a spacer plate and not a mounting plate? They will be able to assist you. Sometimes the holes in the slide are a bit rough and gently using the wrench can fix that. We’ve seen them that need to be chased with a tap also.

@@spencertidd it is a low grade vibration thread locker. You can just screw it right out.

@@SpringerPrecision I mean the plug - how do you turn the plug to get it out?

@@spencertiddthe video describes this. Just use the screw that holds the magwell on and screw it in without the magwell on. When it reaches the bottom of the hole, it will turn the plug and then you just pull it out,

@@SpringerPrecision Thanks - that makes sense, but FYI the video does not show or talk about removal, or maybe I am going completely mad! :)

@@spencertidd 1:00 in it shows you how to turn the insert. I guess we didn't think that we would need to explain that taking it out is the reverse of putting it in :)

Please make sure the bottom retainer plate isn’t on the bottom of the spring. The spring is used when the factory spring needs replacement. Orders@springerprecision.com can assist with more detailed assistance.

@@SpringerPrecision Thanks for the reply

Steel is heavier and adds no value in the 9mm rounds, it also decreases reliability with the common rounds used off the shelf. We’ve made and tested 7075 and they perform the same as the 6061, so we do not want to increase the cost with no significant added value.

@@SpringerPrecision thank you. I have a 10mm. I’m thinking I may get the extended bar-sto barrel and a brake.

Please contact orders@springerprecision.com and they can help you with your question. Typically, it is a darker gray when anodized, not silver.

You only need to replace the spring weight if your ammunition doesn’t cycle the slide.

@@SpringerPrecision Aah ok now i think i got it - thanks for replying

@@anthonysullivan9805 please contact orders@springerprecision.com for customer support. Thank you.

Yes, open end toward the muzzle, closed coil toward the base of the rod.

@@SpringerPrecisionI got the 24lb recoil spring and neither side was closed is that ok?

@@arlovskifan if there isn’t a closed end, it doesn’t matter.

Yes, they are the same.

@@aaronwilson4747 I’ve never seen those extensions. Customer service might know orders@springerprecision.com

@@SpringerPrecision Thanks, I will do just that.

The thread locker is rated to 450 degrees. It should not release under any non abuse use.

Yes.

Please contact orders@springerprecision.com for customer support questions. Thank you.

Please contact customer support orders@springerprecision.com and they can assist you. Thank you.

They work only with the full sized 17 round magazines as the reduced capacity magazines have a spacer to make up for the short magazine tube.

@@otherhanwei our basepads or extensions must be used as the tube bodies are to short to be used with the factory pads. The smaller backstrap will work, but there will be a gap.

@@SpringerPrecision I understand that the 15 round tubes with factory pads are too short, but even the 17 round tubes with factory pads? Appreciate your time!

@@otherhanwei If they don't have a spacer, otherwise they would need to be modified to seat properly.

@@SpringerPrecision Thank You!

You would need to modify the safety or remove it. We don’t give advice on how to disable safeties though for obvious reasons.

Soringfiejd does not time their barrels.

@@SpringerPrecision really . I can’t even get the comp half way through,

@@xgaugesxplease contact our customer support orders@springerprecision.com and they can assist you. Thank you.