- 7
- 46 871
Bon Mil
Приєднався 1 тра 2020
LG Front Load Washer Bearing Replacement
Instructions to install replacement bearings in to the drum housing on a LG front load washer.
Переглядів: 119
Відео
LG Front Load Washer bearing and drum removal
Переглядів 9496 місяців тому
Instructions for using proper vertical support, gravity, and basic mechanic’s tools for an easier removal process for bad bearings on a LG front load washer.
How to machine a piston ring groove in the field without a lathe.
Переглядів 3,6 тис.3 роки тому
Needed a lathe to increase the width in a groove in a new piston that was not machined properly. Converted drill press and hand machined the piston in the field.
How To Patch Drywall
Переглядів 343 роки тому
How to patch a wall using existing textured surface for a perfect match.
How to install cylinder liners for a Kubota engine. #kubota
Переглядів 38 тис.3 роки тому
Using heat to expand and liquid nitrogen to shrink components for an easy slide in fit.
Great tips! Thank you!
Thanks again. Great tip on freezing the bearings!
Very helpful! thanks for taking the time to make this video!
amazing, what is the trick to taking out a cylinder liner?
I must say, I have these 6.4L pistons that are 2.5mm and the only rings i can get are 3.00mm, I'm looking at getting a lathe so either this or that Nice job
Thanks. A machine shop doesn't charge much but it was the weekend as he said in the video so he had to come up with an idea! Good luck.
Как снимали старые гильзы
Does the block deck need to be machined after installing the new liners? Does the deck need machining even if within spec with straight edge and feeler gauges?
@tom6549 The block deck does not need to be machined after liner installation. Liners should be flush with deck. If the deck is within flat tolerance then no machining is required.
Please sack the camera operator 🤦🤦🤦
Guilty! 😂🤣 Rich is the expert. I’m still working on my video skills😂
This is an ingenious Macgyver if I've ever seen one!
It's basic physic... simple💁
Where gloves putting the liner in liquid oxygen, jesas
And you just happened to have a tank of liquid nitrogen in your garage? Where do you get that? I would think that dry ice would have close to the same affect and be much easier to get.
Air Gas or local welding shop.
@@bonmil7924 So at -100ºF would dry ice also work? With heating the block to +200º that would give you a 300º difference which makes a pretty large difference in a circumference.
Dry ice was a test run with alcohol and it didn't work.
Great video! Do you remember what seller did you get your liners from?
They were ordered through eBay on a clients account so sorry but I don't have the seller’s info.
Did you hear the popping sound. No Well you will when you pull it out. LOL. Sorry The Rose bud.
Awesome video! Just what I'm going to set up for my engine task
This is awesome! Where should I buy the new sleeves?
You can purchase full kits on eBay.
Amazing, but you could have stated the second dial vernier reading . And I have cut grooves in NASCAR and NHRA Pro Stock pistons .
I was relieved that he didn't turn the drill press on. Amazing work!
Thank you!
This is the coolest thing I’ve ever seen.
this is dope!! thankyou so much for uploading this and also thanks to Destin for sharing this!
Destin sent me.
How do you ensure the piston is staying true to round as it is turned?
A “V” stop was created.
I'm here thanks to SmarterEveryDay, this is really cool! Super interesting.
Thanks for coming
I'm not going to lie, I thought you were going to turn the drill press on hahahahaha
I thought exactly the same thing
I have that drill press and it's slowest speed is 300 rpm 😬
This is so incredibly impressive.
Thank you. Check out his video on how to install cylinders. It’s a pretty good trick too!
Spreading the good
Thank you for tweeting about it, sir.
This is a great example of understanding the task vs understanding the process.
awesome!! i know im late to the party when installing new liners do they have to be machined after installation to accommodate a new piston?
Yes they do. The OD of the liners come with an interference fit. Once installed the bore needs to be machined to OEM or for your piston size.
@@bonmil7924 I have a kubota with a ticking sound I think a wrist pin and was wanting to just get a standard kit to change all 3 pistons rings and wrist pins so you think I could just leave the stock liners in and not have to replace them the engine don’t use oil or have issues only the ticking coming form rear cylinder and it’s not the rod bearings because I installed new ones and still has the ticking sound from that cylinder
@@lazowelding Liners do not need replacement if measurements are within the required factory tolerance specifications. Size of liner bore will dictate piston and ring size. Could the ticking sound be from a bad injector?
@@bonmil7924 the ticking or tapping noise was from a rod bearing that wore out and fell out of rear piston and we caught it as soon as noise started.once bearings got replaced it was more quiet but still has a ticking sound and we think because bearings were gone it was slapping piston wrist pin too and got sloppy because bearings are new but noise is still there just more quiet..we might swap injector and try that..
@@lazowelding If you take the engine apart again it’s important to measure all parts to determine if they need replacing. Micrometers are your friends
Where do you get the nitrogen setup from?
AirGas. Try you local welding supply shop.
Bahasa indonesi
Did you experience and liner drop after using the engine?
No issues so far.
Awesome I have to do this for my 4cyl kubota v1305 and the machine shop keeps saying that the liner will drip and ill blow a head gasket.
Good luck! Let us know how it goes!
Good job, I have the same bobcat same engine, but I think k I’m just gonna replace it with a new motor
Outstanding! Thanks for taking the time to make this video!
Amazing!