- 33
- 269 134
trumpetdivine
Приєднався 12 січ 2007
Bass Trombone Lever Fabrication....Wasting Time!
I made a bass trombone lever! But....I made a huge mistake!
Переглядів: 119
Відео
Quick Tip for Burnishing Trumpet Bell Flares
Переглядів 428Рік тому
Some of the way I go about burnishing a bell flare. I have found this method is far less prone to creating scratches, and therefore makes less work for me to clean up afterward.
How to Lubricate and Maintain a Trombone Handslide
Переглядів 100Рік тому
Today we discuss my method for lubricating and maintaining a trombone handslide.
Repairing and Modifying a Bach Stradivarius Trumpet
Переглядів 42 тис.Рік тому
Follow along as I apply my Factory correction modification to this Bach Stradivarius Trumpet.
Tuba Valve Repair on a Jupiter Sousaphone
Переглядів 1,3 тис.Рік тому
In this video, I use Votaw valve casing burnishers to repair the sluggish and sticky valves on this sousaphone.
Oiling Rotary Valves
Переглядів 105Рік тому
This video goes over how I recommend oiling rotary valves on French horn, trombone, and tuba.
Repairing a Conn Trumpet
Переглядів 147Рік тому
This trumpet has been dropped. Follow along as I perform the repair.
Repairing a Yamaha Trumpet
Переглядів 536Рік тому
This trumpet was heavily damaged from a fall. Follow along as I go about repairing the damage!
French Horn Economy Bearing Refit
Переглядів 4632 роки тому
This video details the economical refitting of a french horn or any rotary band instrument valve.
2019 Ram 1500 Hemi Straight Pipe Cold Start Low Quality
Переглядів 2574 роки тому
Just installed a ring video doorbell over the weekend and this was a good chance for me to test it.
2019 Ram 1500 Hemi Straight Pipe Warm Start and Rev
Переглядів 6384 роки тому
2019 Ram 1500 Hemi Straight Pipe Warm Start and Rev
2019 Ram 1500 Hemi Straight Pipe 0-60 Acceleration Sound
Переглядів 5524 роки тому
2019 Ram 1500 Hemi Straight Pipe 0-60 Acceleration Sound
2019 Ram 1500 Hemi Straight Pipe 40 Roll
Переглядів 2294 роки тому
2019 Ram 1500 Hemi Straight Pipe 40 Roll
Setting the Gains on the Impala Amp
Переглядів 5 тис.12 років тому
Setting the Gains on the Impala Amp
Impala Factory Stereo Integration Part Eight
Переглядів 13 тис.12 років тому
Impala Factory Stereo Integration Part Eight
Impala Factory Stereo Integration Part Six
Переглядів 12 тис.12 років тому
Impala Factory Stereo Integration Part Six
Impala Factory Stereo Integration Part Five
Переглядів 19 тис.12 років тому
Impala Factory Stereo Integration Part Five
Impala Factory Stereo Integration Part 4 - Second Half
Переглядів 6 тис.12 років тому
Impala Factory Stereo Integration Part 4 - Second Half
Impala Factory Stereo Integration Part 4
Переглядів 7 тис.12 років тому
Impala Factory Stereo Integration Part 4
Impala Factory Stereo Integration Part 3
Переглядів 19 тис.12 років тому
Impala Factory Stereo Integration Part 3
Impala Factory Stereo Integration Build Part 2
Переглядів 60 тис.12 років тому
Impala Factory Stereo Integration Build Part 2
Impala Factory Integration Part One
Переглядів 65 тис.12 років тому
Impala Factory Integration Part One
Hindemith High Notes- Raw Copper Kanstul 1500
Переглядів 47513 років тому
Hindemith High Notes- Raw Copper Kanstul 1500
Just make sure that you don’t give it back to whoever you got it from… There’s no excuse
Corey, you did much more than repair this instrument. I've watched your work on that silver 1994 Bach Strad where you "blueprinted" it. You did much of the same work on this Yamaha. Very well done! And you have to give Yamaha credit for the gold lacquer finish. It looks almost gold plated.
you dont polish the inner slide metal of the three slides? just curious great vid!
@@swoodc thank you! The slides receive a small amount of polishing by virtue of the silver polishing process. However, it is not necessary (or recommended) to regularly polish slides with something abrasive, even like 1800 grit paper or finer. Polishing in any form removes metal, and eventually leads to leaks. The silver polish just happens to remove less than a micron.
where did you learn to fix instruments?
Great job! Beautiful work that shows that you care. I'm sure the owner will really appreciate it!
Man… I hope you never retire!
Always great to watch a master craftsman at work! I'd definitely watch a 3hr video of this resto - especially if it was broken up into 1/2hr parts....
extraordinario trabajo de restauración mis felicitaciones amigo...
Once had a Strad that a collegue of mine dropped so that the bell got damaged in a kind of «spirally fashion». Was almost hypnotized looking at it as I was going on stage and had to play it just minutes after…) - Long story short: got it repaired, but after that it kind of «died», soundwise. I don´t know if that is known to happen? Could it be that the metal stretched in the repair process? Or was it just in my head, because of the «trauma»…?😅
Your neighbor’s subwoofer is very strong 🎉
That's pure shop noise haha.
Where can I buy this tool 😮
Suggestion: Buy a tripod.
Снимаю шляпу перед мастером! ...невероятно!
I enjoyed that, thank you. Let's hope the lovely trumpet is properly looked after from this point on.
Very talented, down-to-earth guy. New sub. I look forward to watching more!
Yes, no noisy valves, just how I like them :)
Wow! I can't believe I watched an hour about restoring a Bach Strad 37 which is my (1985) horn. I have a local "wizard" who maintains my horns, but this is so eye opening. My only modifications are adding a brace on the 3rd valve slide to enable me to play it as an 'A' Trumpet, and 'O' rings from my local hardware store on the 3rd valve slide to reduce 'clanking' as I play the low notes. Love the video, love the care you took, 5* if I could give it to you! Bravo to You!!!!
I include a little O-ring before the first 3rd slide stop nut to eliminate noise when kicking the slide. A tiny felt washer would work, too.
this is amazing work. what is the cost of such a repair ? given the skill level and time involved in repairing the instrument, and that it is originally a student horn, how does it add up ?
im sorry but i dont think metal to metal is a great idea especially on a strad
Speaking of synthetic pads, where do you get yours? I have been looking and can't seem to find the right ones. Can you help?
“You can see how it really goes [̲̅h][̲̅U][̲̅U][̲̅u][̲̅H]”
Одно удовольствие смотреть как мастер делает свою работу
Damn man, you get the hero badge, my man!!!
Wow! That was amazing work you did on that trumpet. Well done. 👍
Зачёт!
Just kills me how these horns get so beat up. I mean I’ve got a 1929 King Liberty that’s been passed thru 5 family members hands with what I would call near perfect condition. Dent free, but the silver plate has worn thru where fingers have rubbed thru and the gold wash inside the bell is thin.
Great work. Fun to watch. Instructive. That horn took major abuse. Disregard bordering contempt.
Hello! I am looking for old and good condition 3 rd valve for stradivarius 37.
Amazing job and the demo at the end was really great! You made that horn sound focused and huge!
Nice channel. I mainly watch Wes Lee, the house of tone, but added yours too.
That was so relaxing to watch! Keep the videos coming please
Awesome job! So rewarding to watch the transition back to beauty. I would love see you refinish a lacquered Bach Strad and how you prepare/ tint and finish your clear. Great work !
Beautiful work. Do you take new customers/projects?
I love watching stuff like this
You know the vid gonna be good when the creator’s icon is just a letter on a monochrome bg
Lol! I'm not a fancy person by any means.
Zen and the art of trumpet polishing 🙂
Fascinating. You're like a chiropractor for trumpets. Impressive craftsmanship. Where did you learn how to do this? Have you ever come across a trumpet that couldn't be repaired? I had a Bach 37* in high school. Haven't played for years, but I just picked up a used Bach 43 to start practicing again.
Super impressed with your work! Are you accepting repair work? I have a trumpet I’d the dents removed from the bell and a couple of small dents in the tubing that goes into valve casing. If so, do you have a website or can you provide your contact information? Thanks!
Muy interesante a lo que realizaste para agrandar esas partes de los rotores , en qué ciudad está tu taller? Saludos desde 🇵🇪
I have the CLASSIC '65 Strad I bought when it was brand new. I remember how it smaller when I opened the case for the 1st time.
I want to know what to expect to pay for this type of repair.
SUPER!!! 👍👍👍🎺🎺🎺
I'd like to know what this work cost your customer. Looks quite expensive.
Sensacional!!!! Fantastico !!!! Você é muito bom no que faz!
how can I contact you to repair my daughter's Strad? it got stepped on the dent was removed but it still has some creasing along with some smaller dents.
Simply beautiful work!
Great job on the trumpet
❤❤❤❤❤❤
very good