Відео

Was it necessary to remove the whole fuel injector pump? I think the fuel solenoid was enough

IAM interested to find troubleshooting

𝚋𝚛𝚘 𝚑𝚎𝚕𝚙 𝚖𝚎 𝚏𝚒𝚗𝚍 𝚌𝚛𝚊𝚗𝚔𝚜𝚑𝚊𝚏𝚝 𝚜𝚎𝚗𝚜𝚘𝚛 𝚏𝚘𝚛 𝚃𝚘𝚢𝚘𝚝𝚊 𝚅𝚒𝚜𝚝𝚊 1997 𝚖𝚘𝚍𝚎𝚕

Thanks for the idea🌟

good batteries i open injector lines and prime. saves batts

❤

Good

So helpful, was able to get my AC working again. Will have to change the wire entirely.

This malfunctioning in our Dg set, hope the suggestions given must work for us. Thanks for sharing.

Again thanks bro

Yes another idea thanks again broooo........

Thanks bro gor the info keep going brother

❤❤❤❤

Very good example and good simple understanding 🙏👍

Which one is the auto button on the display

Been looking for this solution everywhere. Thanks for providing!

hindi

Good evening my volvo D9 generator say engine can bus fault emergency stop hardware any ideas how to fix it please

ua-cam.com/video/7KCAP_N2o2w/v-deo.htmlsi=RrNmNmPeBdhnqf3N

Good work sir, but how to troubleshoot a generator that stops after running for some munities after stare

Thanks

Have you had any issues with the wave washer making noise? I was concerned the soft rubber sidewall sealed bearings wouldn't hold up over time next to metal wave washer pressed against it.

You make too big a deal of just screw it into a stop by hand back it out one turn

This model same generator starting very well and after 1 minute automatically shutdown.

Very informative! What happens with the coolant if you remove the indoor unit for cleaning?

Dear, Sir pls make another playlist where u Only upload generator trouble shooting & it remedy.

Check that magnet for metal chips which causes a malfunction. Also air gap between magnet sensor and rotating teeth.

i need a mull timitter🤣🤭

Speed sensors fail by shorting through or becoming an open circuit. Check them with an ohm meter. They will have no resistance or infinite resistance if bad. I've never seen one be out of calibration but if that was suspected, they should be checked against a strobe tach. Shoving paper clips into the harness connectors will provide a nice tunnel for water to enter and corrosion to form inside the harness.

ua-cam.com/video/-mFO2LvLQV0/v-deo.htmlsi=rWBIPoCYtqnI5xo3

ua-cam.com/video/-mFO2LvLQV0/v-deo.htmlsi=rWBIPoCYtqnI5xo3

ua-cam.com/video/3KykFyM69xQ/v-deo.htmlsi=58_RnCxahmFxX5H1

ua-cam.com/video/8U6Yu3nxvuE/v-deo.htmlsi=lngVqIz7F_Bj4Flo

ua-cam.com/video/4O-50ywg39c/v-deo.htmlsi=AdRBrYQmoWsvJ8mh

ua-cam.com/video/7KCAP_N2o2w/v-deo.htmlsi=CCI63mzsDgPNLISH

ua-cam.com/video/9jCTgVvWVgo/v-deo.htmlsi=ivzByS6r9NC7OGOA

ua-cam.com/video/3KykFyM69xQ/v-deo.htmlsi=wMlbyiCYuB504mis

ua-cam.com/video/-mFO2LvLQV0/v-deo.htmlsi=ZMEWR1ehcxxSXQZO

ua-cam.com/video/-mFO2LvLQV0/v-deo.htmlsi=ZMEWR1ehcxxSXQZO

I have the same issue i have checked the wire and is ok please what else can i do to resolve this issue

I like to know more about it again

this is good stuff keep making this educational videos thank you!

please keep making similar videos you are the best!

Love this tutorial you teach very briefly ❤

Greetings engineer I have this issue with one of my generator i am doing maintenance,thanks very much for the procedure,i will go and try it there,but was show me speed sensor disconnected

Thank you. This is well done and clearly shows the process. Good job!

ua-cam.com/video/NR0FgvvIzec/v-deo.htmlsi=nFBoHZRh7Aw-k5gD

ua-cam.com/video/7KCAP_N2o2w/v-deo.htmlsi=hjs16-_iix9kUo3a

ua-cam.com/video/GseWzLig-k0/v-deo.htmlsi=YRZUGLgaS2W8VBNR