Відео

Watt motor is that and is it a "haibike" middrive

mine makes this noise but smoke comes out as well lolol. I assume that's not great. I was getting exhaust smoke on and off for a few years and now it's pretty constant. Oil is going down. No coolant loss. I am assuming it could be the pcv is bad, maybe worn piston rings, or something causing the air to fuel ratio to be off. I have 117k miles on my 2015

Hi As I was attempting to change the speed from 20mph to go faster, the speed counter went past 99 and reset at zero. Now it only goes from 0-9, where as before it went from 0-99. Is it possible to reset it back to 0-99? Thx

Hi, will this work on the Heybike Race Max as well? In the U.S, the max speed of this ebike is only 22 mph, but is advertised as 28 mph. If so, can you please tell how to make this ebike go to 28mph as this is a very demanding bike and many people want to know how? Thank you.

How do u get ur heybike mars to 7-7 all I literally watch ur video a couple times and im confused

It’s normal

Thank you, great video!

I used this method to unlock my Cybervelo MARS700. My buttons are configured differently as his is + power - and mine is power + -. I pressed +and - together to open settings. Then pressed power button multiple times to scroll throw settings to PO8 that displayed my max speed of 32mph. It might be a different PO# on your bike. You will know you are at the right setting when it is displaying your maximum speed. And this is where you will change it. I pressed the minus - button to 0 zero. Then once more and it went to 100. You can press the plus or the minus button to get to 100 I just find it faster going backwards. Good luck and be safe and follow your local laws. LOL

👉will this work for Heybike Race Max as well?💥

Life saver

Mines were set at 45 I lowered it now it won't go back to 45 should have left it at 45

My display panel won't come on what to do

Looking at getting one... probably go with an ex mark or cat....very good video.... thanks

Andy check out this site. It explains how to set up speed and voltage and how many speeds to set up. I recommend 5 speeds. But keep the bike at your business and I will bring battery charger and set up the correct setting. Don't worry the error flash you see is nothing to worry about. I will dial it in if you can't figure out. Don't stress it's all good. I promise to come by tomorrow and make it run perfectly....Thanks again the phone works great....see you tomorrow.....

Wouldn’t that burn the motor

Can you please put a video out how to reset to original settings on your Mars hey bike 1.0

Wouldn't trade mine for anything.

It’s that normal? I have the exact same problem or sound on my engine, what could be?

Tell me how family said mechanical breaks are better than hydraulic

How do I reset mines to stock setting???

Thanks for the honest review! Think I’ll stick with the Ferris ISX2200.

Does your Gravely motor have a long start instead of firing right up when you turn the key??? And does your gravely motor acts like it trying to keep running when you cut it off??? It's like the timming is off a little bit on my gravely motor the 26.5 hp

Anyone know the codes to make the thumb throttle full power all the time. I want to set PAS 2 to cruse control 12mph and thumb throttle petal to the metal. Thanks

You are Da Man! My bike went from 22 MPH to 38 MPH!

Sounds like someone rapidly fisting a jar or mayonnaise, normal nun the less. Ofc it’s gonna sound different when you take off the plug because the sound is muffled

Is the process of unlocking speed the same for the Mars 2.0? Thanks

Mine is at 45 already. If change it. It goes to 40 and it can’t go back to 45

Hello I really need to know how to remove the speed limiter on E-Mountainbike MONTIS EM 1726 by FISCHER with bafang display. Can u tell me how or if its possible? The e bike is really fast but its limited at 25-27kmh

Sound like there’s no oil in it that’s bad

Thank you for review of your mower .l was considering buying one but I think I will look at other machines. You have saved me a lot of disappointment. I know you said you already had cleaned your deck. I would have liked to have seen it open.I have never seen a machine like this. Does it require a lot of brute strength?… Thank you again

I want the info on the other settings is there a pdf somewhere. I want to know and have electrical experience. I find the way the bike continues to accelerate after letting of the throttle uncomforatable. Do you know the model of this display so one can dive into the other qspects deeper.

At last - an ebike with pedal assist level 0 / ZERO ! Can you somehow deactivate the unwanted, intrusive pedal-assist and ONLY use the throttle on all ebikes? And/or can the PAS wires be physically disconnected? If not I ain't buying one. I - the rider-owner - want to decide when I need power - not have "pensioners' pedelec" pedal-assist kicking in all the time. It also increases range if ebike-riders can activate power ONLY when we need it or want it using only the throttle with no interfering PAS / pedal assist!! Paul G

Anyone know how to do it on a Heybike race max

I have this model of mower and it recently started mowing not level and I am wondering how to level the deck

Great review. Thanks.

Great video 👍. I have set mine to 9 as it’s on a trike so need very smooth PAS. I’m sure that before I made the alterations that the thumb throttle was limited to 4mph but now it seems limited to about 13mph. Would know how to set the maximum back to 4mph as I require this for my trike to meet UK disability requirements when ridden in pedestrian areas. Thanks, Bob.

That’s redundant if you get a ticket for a non ICE vehicle. Them bikes look enjoyable to cruise around on.

How do you turn the light on the screen?

Thanks for the video. I managed to change the settings on my Yosepower set up as it has the same display. What was important for me was changing the 5 power assist levels to 9 and then evening out the wattage settings to each of the 9 settings. This made a huge difference to the way my trike performs as the pedal assist and thumb throttle was very erratic at slow speed which was a bit daunting on bends and in shopping areas as I use the trike as a mobility aid. The acceleration has certainly smoothed out to the point that I hardly notice it kicking in. Not all the adjustments you explain are in the Yosepower instructions which is a bit disappointing.

I have the same problem, and two misfire

I know this is a older video but I just noticed my wife's 2018 Ecoboost Mustang does the same thing.

Mine is Ananda similar to this and when I hold the plus and minus together nothing happens 😢

I have one works good

I'm about to buy one... DID you find the origine of the probleme ?

My 2017 is doing this same thing right now and it’s driving me crazy

I did this and it doesn't seem to work

Could I turn off pedal assist fully? Like just have it give power when I throttle

Hello 2022 trelago e bike

Great video but why doesn't the settings save?

It worked! Upvoted.