Відео

@@horypeti28 use imagination :)

@@horypeti28 any ideas yet? Tip. Think two mosfets on a similar switching circut. But adjustable.

Thanks! I may use it soon again!

@B.Cote39 Thanks lol UA-cam is censoring some of my own comments again. Pretty sure I replied to you.

Not doing saucer experiments

@KyleBurke-x7h no it may not need to be totally within it. When you fire the top and bottom ring coils, you will collect that also in the conical coil. You will collect its BEMF and also the conical BEMF. Imagine the perm. Magnet field as a bubble. Or go yt search Ferrocell videos. You'll see. Then the ring coil is also, making it's own bubble. Not too unlike the permanent magnet. So we just need them to interact/cause change to the permanent field as a vibration.

@Heliarc91 ohhhhhhh, don't mind me haha but, so you mean like connect or, interact the transverse and longitudinal waves, using the same frequency, causing vibrations? Last question I promise hahaha.

@KyleBurke-x7h no, just the permanent magnets field. We just want it to vibrate where it sits. By adding a core material, it then couples through it so may make it run better.

Just gotta be strong lol. I did full pen weld this. or almost full. Beveled the bar to about a 1/4 diameter left. so about 90% pen.

@Heliarc91 right on!

@B.Cote39 i bet it is lol that's alot of capacitance

@ im only turning by hand and end up with a surplus after discharge , nice work BTW !! 😎

@ old man builds live in 20if you want to chat more ! oh and great presentation also , glad someone finally mentioned doug! Like most greats he will only be acknowledged long after his passing 😞

@B.Cote39 Hi. Yes, I had many email conversations with Doug. We discussed door designs. I am an Ex Welding and engineering instructor. We had a few designs. And also pressure vessel designs to withstand 1000ft of ocean. I will publish them eventually. Since I don't have official engineering software that can test strength, I have to be careful declaring something can or will work. But it isn't too trivial. We only need to ride out a few days of horror with enough o2 supplied to make it. Not impossible. Im not giving up. I'm going to try to teach young welders how to build their own shelters. Were going to give it one hell of a fight!

@ i remember him mentioning he was in contact with a builder engineer, you know even if he is wrong (which i pray that he is !) its better to have a plan at the very least ! Though i believe at the very least we will see a “grid killer” in near future , not sure if your into FB msger but im on there as branden cote , pic of my daughter and I , seems we have much in common if youd like to chat more ! I do a little fabricating myself 😎 ironically floating rental Domes , though not intended for end of the world type scenario you never know where these ventures take you 🤔 option B survival plan or phase 2 would be to escape the iceage and head for Ecuador, marine biology seems to have made it through many of these “events “ could be viable option for humans as well

@@KyleBurke-x7h No thank YOU.

@Heliarc91 haha thank you, keep at this stuff brother you may be part of the good change in this world.

@michelmorel9208 please post it online and show everyone your progress!! Glad you liked it and found this interesting! I am going to dig for the DXF but these are super simple on tinkercad once you get used to the negative shapes and merging to make new shapes. (Fitting negative shapes inside shapes and fusing, causing your voids)

Check first take I just released!

@@voltixD Id have to do some checking with sources but I believe it's recent

@Heliarc91 It does look recent. Very informative too!

He believed last year.

@@Heliarc91 Cool thanks 👍🏾

Check 1st take i just released.

Check 1st take i just released!

Thanks buddy. I hope it was entertaining

@wolfgangmetcalf9557 the Metglas core, or almost any transformer core does this. It's what iron does. Transformer iron doesn't like going above 400hz much though. Metglas is good to atleast 10khz. Some much more. The issue with metglas is though since it's tape wound you won't get the magnetic flux penetration as you would a vertically orentated core material (in slices)

Bearden is great, and I think he has hit the nail on the head in many things. I'm actually writing a book on some new physical principles of the vacuum and interacting myself. I took a break from writing. However, I plan on doing a series of videos explaining my theories with representations very soon. Watch for this I'll be posting soon!

@thecontact2609 I am too! About electronics and prepping! Mine will have a free watermarked PDF available to all. Let's do it!

Also, I might have figured out a way around the metglass situation. I drew up a schematic and think it's worth trying at least.

Haha, I'm not sure how to share it though.

Glad you like it. *I realized I no longer have the DXF. If I get enough requests I'll remake the DXF and give it if people can't look and make their own.

@@Heliarc91 I gave out your channel to everyone in the chat today and they are excited to talk about the meg and the pole shift.

Thanks! Thought id share that was a B***H to weld!

@@overunityresearchchannel Hes a great team member!

@EdwinDeMars Hi, Sure, go to above unity, ferrite at work, or see my pole shift video. Go 4k, and zoom in on it. Screengrab. Tip: Flip the polarity of L3 to your transistor. Resistance very important. Winding direction Critical.

Thanks!!

@BeanMan5621 I've thought of mounting it on one a bike and tuning it.

Use it as a main weapon motor for a 250lb combat robot. You would also need at least 10 grand for other stuff though..

@@Heliarc91 that would be sick!

@external316 like a battlebot ? Lol

@ exactly.

@Timtron432 Yeah wasn't too bad. I'll try again with the new 36 pole with 1,000 wires 😞 Thanks 😀

No. The Power supply is providing the 78w, driving it with the driver at 136w. which 136-78 = 58w ECM generation. It helps me make changes and calculate if i am "losing" by trying (x) or "winning" ... and (x) can be a TON of things i can change and do. I have many duplicate ECMs so i have a control as well.

@ yes, that’s what I meant! What I hear you saying is you put 78w in, and getting 136w directly from the output. But you only get 58W of overunity, because 136-78=58w. Is that correct?

Essentially what I’m getting at is the COP is over 1?

@ashercorbett8089 no you have the math right. But it's not OU it stops when disconnected. Unless I'm wrong on my own video lol I might have to go back and check now ha ha I mean I wish you were right lmao

Can't send links on youtube. However I believe i have archived the videos you are referencing.

@osvaldocorrea789 this is a old project I've moved on from. But yes, i knew it was oversaturated. I mentioned this in many comments.

@@nathanbunten4299 Thanks so much!! Love YOUR content!!