Відео

😂😂😂😂

@@massimoregalino hi you need to set the stopper gear assy with the handle crack position

It looks a lot like the one from Precision RC, am I correct?

@@danieldoyle6001 custom Made sir

@@danieldoyle6001 same concept but I made my own for the sizes mostly shimanos from 1000-30000 sizes bearings

@Roddreel If you made that yourself you should sell them, they’re an awesome design. I believe the Precision RC “the greaser” ones have been discontinued which is a shame.

@@Demogarr I attach the worm shaft pin then easy for me to put the c clip.

@@Roddreel I finally figured it out, thanks for the response!

@ welcome bro anytime

@@pablogomez7124 no sir keeping for collection

it came with the box.then i modify for bigger grip

if too much so far im doing this for more than 10 yrs no complain at all.Is how you put the amount of oil or grease.try to think two metal rubbing each other with no lubrication what will happen? thanks

Nope it doesn't,I also put grease on the ARB and also no complaints

1/8 craftsman im using

there are 2 marks near the rotor.not too loose and not too tight.

@@Roddreel Are you talking about those two little dimples cast in the rotor and what would you line up to them? reason am asking i took mine off and didnt notice or mark the nut so wondering how to position it. the cover for the nut is toothed so to an extent that also determines where the nut lays for the cover to line up with the three screw holes. Also i notice when you were putting the side plates on you didnt tighten down and you attached handle then tightened. you were checking for binding ?

im not familiar with sizes but the smallest from craftsman as long as its long 3mm head

thanks sir how i wish i can fish in your area soon.

capahirodd@yahoo.com

to make sure you need to open

there is oring on the spool and side knob.or in the bearing email me send me picture pls@capahirodd@yahoo.com

.8 hex screw tool

@@Roddreel and for rotor nut please?

synthetic sir

Ok sir thank you

Just practice sir

I guess it’s a nice place but sad to say when I fish the place the weather is bad but no choice just trying my luck.

English pls

Lighter fluid

I so service too some of my friends reels as well

@@RoddreelI need a reel friend

thank you bro.sorry just cheap editing and mostly just raw footage

😂😂😂 lingaw pud pero sakpan ra gihapon unsai ilang gusto kan on

I was develop in a lab of one of best manufacturing oil and grease company in Dubai.It was lab test for wear and tear.This grease were used for aircraft machines.Test for cold and high temperature.So far I’m using it for 12 years before I share this to public.I have no complaint using this for hi end reels like Stella’s and SOM if you are familiar with those brand.

@@Roddreel that is great! I may try some.

@@ShorrockPaul if your near to me I can share to you I’m in Memphis just moved in

@Roddreel Thanks for your very kind offer but I live in Ghana . I have friends travel to Dubai on regular basis. I will ask them to bring me some if you can give me contact where to buy in Dubai. Have you done any shimming on the Stella SW models. In particular the latest models 14k or 18k for eg. ?

No sir

If your near to me I can share I’m in memphis.i can send the oil and grease by cargo.

thank you

can you tell me what accessory you use to remove the bearing and turn it at 11:10 thank you very much for your response

@@GregoryS-p6r hi it is bearing puller you can order to bad baearing tool

Thank you sir

Ya I forgot to bring my gar grip pliers

No I don’t use shimano grease anymore I use my own grease full synthetic but different viscosity

ua-cam.com/video/XtZPZBPnpAE/v-deo.htmlsi=MUDj39ygkvg5TFy2

@Roddreel very interesting are you a chemist or engineer. Not everyone can mix their own greases.. very impressive! BTW. What is that little bearing spinnng tool you use. ?

@@ShorrockPaul custom made bearing checker

They have grease the arb stock bearing but I put an new grease low viscosity looks like oil but that’s grease hi temp low viscosity

@Roddreel cool. You taking this reel servicing a step beyond. Am impressed with your skills. I am just about to delve into my Stella sw 14000xg 2019. Is brand new. I have not fished it jus spooled braid on by reeling it under tension. But reel feels rough to me (compared to my butter smooth 18k stella also brand new) . Want to try figure out what is going on inside it.. it does spin very freely, no binding, but Haa a grainy' feel almost a slight rumble.. difficult to explain. If it wasn't next to the smooth 18k one may not even notice