Відео

I bought some for an unheated room since I can do it myself. For the life of me I could not figure out how they snapped together till NOW. Easy Peasy. Thank you

amazing guide! watching this before I start assembling mine to hype me up for the task questions for ya, once it's set up are you able to wiggle it into the right spot, or is it too heavy and I should definitely build it right where it goes? anddd how much space do you think I should leave behind it to have space to put weights on the cable tower? working with a tiny garage for this build and every inch counts 😅

Visually seeing the wiring job during the daylight adds that extra something, something!

Where did you buy the rebuild kit?

You should make it so the wire go through the bracket, not outside the bracket. You’re going pinch the wire and create a dead short/ fire.

Hey, Awesome video! Did you have any issues with the pulley system? When I pull down it works fine but, on the way back up it takes forever for the weights to hit the bumpers. Almost like there is too much slack. Any ideas on how to fix this? This is my first rack set so please don't come for me.

Yeah idk mam. What is the argument for using the saddle tee? Is it laziness or u just think its ok?

No.

Yes the hate is going to come. Alpine air is garbage. At least the unit you're installing. I had my unit installed and went through every single tiny bit of adjusting to make it better more efficient etc. was still a waste of money. The humidification that it gives out is minut. I was shocked when the representative told me that the best it could be. I only gained 5% more humidification at best compared to without. this is during the winter where is needed. Yeah they work, barely.

Certainly handyman work

Humdistat was too close to the bypass!

Just needs some duct tape.

That 26 gauge is too light to be cutting things out in pieces. Offset snips would help more

I know what side of the Mississippi hahaha

Saddle valves are illegal in the code books.

Why’d you cut out a rectangle in like 6 pieces instead of 1?

Thanks man, I like your style 😂

Saddle vales work and will work for decades. Until you go to turn it off, or it just decides it's served its time. Then things go bad very quick.

Ah saddle valves. They work until they flood your basement in a year.

7:34 Only use a saddle valve when you want FLOODED basement! Come on bro, cut the copper....drain the water ....... sweat in a 3/4x1/2 tee.....install a 1/2 stop valve (ball 1/4 turn) and run a 1/4 copper line to the humidifier. No need to cut the white at the humidistat, just run it though and cut the red for the terminals. Its low voltage, so its cleaner to use a crimp fitting instead of huge wire nuts. Should have connected the water line to HOT water, it aids in evaporation. Sorry bro, not much of a handyman....

Yes saddle valve nowadays a big no no, but dude tilt it a bit further up the pipe next time. Reduce the chance for sediment building up in it as much as possible, after all it’s not like you’re ever gonna really be able to shut that off. But I think anyone doing this it would be a good idea to at least see if they can find one that has an actual shutoff, in case you have to replace or service this thing.

Did know there was a such thing! Thanks for this video!

Nice video. I have one that was even professionally installed. I found many times once the filter becomes calcified, rather than down the drain, it leaks out the case. I'm gunshy to use it this winter. I lost a room of carpet last winter due to it overflowing. I now have several water sensors on the floor to hopefully prevent another occurrence. Have you seen this? Am I wrong in assuming the drain hose ( which I checked) is the intended destination for overflows? Thanks for taking the time to show this installation. I understand mine better now.

Did it need a transformer

old cloth wire, looks like its from the 1960's

You charge 975.00 to change that. Gave her the discount.

Thanks for the video! The manufacturer video is pretty decent but sometimes it just helps to see an actual human doing it by hand

Don't you need a dimmable bulb for this to fully work?

You dont need to take apart the tub to get hair out. You just need to know how to use a plunger correctly

I'll give it a try. Thanks

How many Pulleys are on this model? I wanna upgrade to the Aluminum ones but wanna purchase them before it gets here so I don’t put it together and then put the aluminum ones on when it gets here

I always prefer fixing stuff over replacing stuff, but a bathroom sink faucet is 30 bucks

Most important step was skipped 😂 I'll wait for it.

They make a tool to pull the cartridges for under $20 if you are doing multiple

Bro? Really? A us.infantry.sergeant.of.COMBAT.marines can poop in war with... 💥 BOOM 💥 BOOM 💥 BOOM 💥 so, we're sure a dood can poop in peace with drip ,drip, drip.

Last time I replaced a cartridge was in a sink that takes 2, it was so corroded I ended up going at it for about 45 minutes with both sides of a claw hammer.

The camera has been mounted upside down in the video. Something that I am pretty sure I read in Ring stuff that you should not do. I will try and fit the camera right side up when I install mine using those mounting brackets and hope I can. Thanks for the video all the same.

This is the way!

Where to buy this

Mmm I didn't know they had a cartridge there, I just learned today. We never finish learning.

Good job

"abd i said stop balding" your going to be sleeping on the couch tonight😂

outdoors ??

so im planing on getting one of these soon but mine will be out side in scotland the only place i have space is this a good idea and how could i go about giving it some extra protction

Exactly what was causing the squeaking on my Maytag. Great instructions, great video! Thanks so much

Great job. They all seem so simple once you explain them. Thanks

I think im getting pay some crook

Exactly what was causing the squeaking on my Maytag. Great instructions, great video! Thanks so much

Who just slaps duct tape

I wonder how to take them apart?