Відео

So, there is no clamp on the vertical end of the pipe flash?

Jesus is coming back! Jesus is Lord! !Jesus is the Way, The Truth, And Life! Jesus loves yall! The unbelievers will have to suffer Gods wrath! Jesus died for us so that we could be saved!

You should use a penny roller around the base

Well done 🏆

Hydraulics, robotics, you go mumma

You weld the cross seam first then the top sheet so you can weld straight through without stopping, you guys should not be instructing anyone on TPO, you suck lol.

I didn't see you do an air dam before welding the outside edge.

Muy lento.

I do these drains all the time i find it easier put bolts on before the caulking then after the base flashing is over and set i use a hammer to tap top of bolts it makes the perfect size cut for where bolts go.

❤❤😢

You do not have to wipe the magnet every time you would never get done

Why not just put the pitch pocket together before you weld it down?That's what I do

why do that when they male a pipe boot all that work just for it to fail eventually

Well done, thanks

You use the wrong roller to the corners

Im on Facebook if you newbies want to see a professional

Can guys please stop using the hand welder going across your body? I need an application JM

This is the stupid bro, get a collar

This is quite the process , with tape, flashing , calk plus the original target piece. No wonder its like $25.00 a square foot . How long can you expect this to last exposed to NJ elements?

Le faltó donde atornillo pegamento

The pulling apart of the sample test plate weld has always been the most difficult part without damaging the test. Any recommendations that might make that easier?

Hello, Hope you are well. I already visited and analyzed your UA-cam Channel. Your Content is really Amazing. But channel growth is very poor. Already found many problems on Your channel. Just need to customize Your channel now (Setup, Optimize with High-quality SEO) Especially need SEO services.

Now try all of this outside in the real world.

Ведро герметика и вопрос решён.

Excellent.

I’ve been in roofing for 10 years and never seen a scupper roofed in like that. Caulking at the seams? We put a target of material and 4 corners of detail

Advice for anyone who does this: done ever pour it out around edge like this, it will prematurely crack and leak. You want to go up the pipe and let it drain down creating a small slope. It also works better if you use painters tape on the tpo and overfill an ⅛"-¼". BUT NEVER leave it flush at the pipe or below the lip like this

I install TPO membrane as swimming pool liner. The pools looks awesome.

Хуже работы не видел ,не умеешь не лезь..

Do you need an employee?

Saudades

Cold wrlds

Joe is awesome!

good lesson. I have few minutes to start to see your videos. I like work on top of roofing. flat roofing.

Always clean before welding

Sad JM still refuses to make pre fabricated corners so you don't have to strech the material and make it a weak point. 80% of EPDM leaks are always the corners.

No audio

impressive on the steps and overlays. Think "insurance" will cover all these steps?:)....

Awesome video

thank you

Takes care of my family very good.

Beautiful Boots 😊 Irishsetters?

Good 👍 Buenos

And 2 T patches

And cut edge

Missing water cutoff and clamp

Where is the water cut off at top of the curb ? Not to mention your patch at side lap of curb. If you we're to 45° cut at side lap your corner would have covered it. Kinda crazy ! Little more time in the field needed .

is there any possibility of wind-up lift since there are no screws and washer to hold the TPO in place?

❤👏👏👏👏👋🇧🇬

Heyy i know this guy