Відео

Whats wrong with this particular wrench you don't care for ?

I take it you've tried out this spray gun?

Sounds like the tool is having trouble possibly from the deletes you have done there's an tuning tool for desile trucks when completing deletes and such ill ask about it for you and find out the name

Sounds like an bad safety neutral switch possible. Is there an code on the vehicle

The valve or valve cover ?

@@wrightsrrt871 the valve pa66 gf35

I got mine at O'Reilly's same part number

No the motor was not shaking on this vehicle. If your engine is shaking could be out of timing ,tuneup or just need rebuilt.

So what I belive your dealing with is you have to pop it loose and get all the bolts to pull out the valve cover as there designed to stay in as to not drop stuff into the motor during disassemble and putting back together. Then once loose you canter the upper part of the valve cover and slide it out between the block and harness outward towards front of car! This was not easy brother and will take a little patience for sure but is the more challenging part on the grand cherokee vehicles even the 2000 I work on time to time has more to move out the way on passenger side. Good luck and thanks for viewing the video! When I get an go pro I'll be filming the actual repairs in the future!

The pcv valve has been upgraded and is why there's only two holes for it so it will clamp down more evenly when fastened down plus in the video you'll see where I talk about there's an upgraded hose to buy as well for the upgraded pcv valve. The reason is the direction of the new valve will be different so the hose route is needed to be different as well. If you want the original part you'll only find it at the dealership and even they are updating them to the new design.

Thats the upgraded one with the two holes

@knockoutking4130 yes and don't forget the hose !!

Sorry I don't speak Spanish or Latin yet so don't know what your saying

eBay

Welcome and just trying to help people out!

First check all your fuses and relays to make sure you have the right ones ,right size and also there working correctly. Next it sounds like an overcharge situation so make sure your battery is the right one. Next if it persist try new alternator and or an voltage regulator to keep circuit from over charging system. My opinion Is possibly alternator is putting out to much voltage to battery and creating back serge making the alternator to hot cause the battery can not absorb the power fast enough that the alternator puts out. Next thing I just thought of would be to tight of belt putting tension on pully .

This was the fix for this client's car as far as this vehicle goes but I've had to revisit this vehicle this week actually is sitting in my driveway right now and I was going to make another video on it soon! So what I found out was the valve cover gaskets was needed but didn't come with sertain gaskets like the pcv valve gaskets and the cam sensor gasket so by trying to use the old gaskets it leaked again so spent $22 at the dealer for cam sensor gaskets and the one that was the problem was the pcv valve you have to buy the whole part just to get the gasket dealer wants $109.00 and oryleys is $43.00 but the part dosen't come with the right bolt pattern so I just took the gasket from it test drove it and no leaks! Also note that this is just an problem for this vehicle and may not resolve your issue but also the pcv valve is located right above o2 sensors so if your questioning the leak run the car like I did with the intake tube out of blocking your view and go get the ridgid inspection camera in plumbing at the home depot and investigate that camera is $80 and has saved my guessing and time so many times brother!

Rainman repairs just posted an vid on the other common issue that leaks which is the oil cooler and fill assembly so that seems to be an issue as well, just thought I would give you the heads up on the vid was posted 4 hrs ago!

We used the high tech dtm for this phase and your right if we had slow it would have layed out smother I was trying to adjust as close as I could to the panels and speed up hand speed to adjust for the heat but I was at 3 inches and didn't feel like closer would be good lol

I posted the video with the basecoat on that van and I hope you don't mind I gave you an shout out for the advice you give out to those looking for it.

@@wrightsrrt871 I don't mind at all brother. That's what we're here for. Anytime. I'm gonna check it out 💪🏼

Yes it dose

Yes it has the switch to go both left or right.

Now that you have positive feedback we're good my friend I work hard I even have been working trough surgery and cought nahmonia and had an tooth ripped out my head all in one month lately! I appreciate that you fallow us and hope we have been able to help! Sorry once again if I'm not the greatest at filming and don't have an gopro but I try to afford other things then gopro having 5 kids and im glad we my have changed your opinion about us! You seem to be fair in your ways and I commend you for that and I appreciate you sticking around to see more 💯 just know I never cut people down just try to help and uplift folks the world is just so full of hate now and could use an little bit of an helping hand ✋️ 😉 I'll look into your channel hope you have some good videos

@@wrightsrrt871 ya man you have had a rough go of it lately and I admire your positivity. If everyone could see things your way the world wouldnt be in the trouble it’s in. Keep in touch and I’ll keep watchin! Take care. Oh ya what state do you live in that its so hot?

@The Hidden Truth I live in CA poverty flats also known as redding!! We have one of the biggest car shows here called "cool April nights". It's alot of fun and why I chose to do cars again after so long brother. Anyway maybe we get together sometime if your close to me! Other than that keep your head up and im sure with our skill sets being similar you'll succeed in everything you do!

@@wrightsrrt871 I’m south of you in Riverside but always in the desert doing hobbies and off-road ing. We have 40 acres up in the desert just west of King of the Hammers. I used to go to trade school in Fremont when I lived in San Jose. Right on bro keep in touch and take care.

I'll be posting an new video of the torque wrench today so keep your eyes and ears available and if there's anything I miss this time let me know hope this time it's more helpful! The reason for it upside down was we do completely unedited video channel to keep things authentic! Great to see you subscribe and once again hope we one day can help you out with something in our videos and thanks for busting my balls in an nicer way than the guy who says the video is useless when there's no other video on here about the wrench and its pretty much time for the 1 year durability video of this product. Well post video shortly and have an good day!

@@wrightsrrt871 thx man!

Yes sir if you need any other advise please don't be afraid to ask!

@@wrightsrrt871 I may well take you up on that!

@FoxADV sounds good I work from home mom and pop type buisness so I'm available on and off for questions!!

Thank you for wishing good luck 👍

Already picked it up and I use both to me they work great 👍

Thanks man for that information, the suspense was killing me

@TERRELL SCAIFE the 1/2 inch drive in video is the one your talking about and I've used both for an good while just keep them oiled up and they'll do you justice I even use the husky watch wrenches and all there other stuff it's an quality low end brand. Eventually I want to try the Milwaukee brand wrenches and such but there more spendy!! I try to do my best to stay finding good tools for good prices

Yes, nothing wrong with budget tools it’s no shame in my game if I go to HarborFreight and get some tools I did now I’ve been using for years I think Mother’s Day 2017 I got 3/8 shallow set and deep impact sockets both sets for just a little bit under $20 and those sockets haven’t filled me in five years

@TERRELL SCAIFE yah husky is gear wrenches low end stuff I shop harbor freight for some things bit I avoid there electrical tools for most part as I like Milwaukee power tools

These are commonly known as interference ground straps and they are also for jumping the ground at where the battery ground bolts to engine then jump the ground to the body hence fire wall the secound part it jumps to is chassis. The reason for this is so you don't have to run an long ground for radios and other stuff like rear tail lights they can be grounded to either body or chassis of your own choosing vs running an wire all the way back to the engine or battery ground. So basically you can locate them anywhere as long as your jumping ground from engine to body and chassis. It routes typically from body to an engine bolt located passenger side by top of transmission bell house then jumps to an bolt on the top part of chassispassager side by the front wheel the one in video is for the transmission to ground off

@@wrightsrrt871 thank you very much!

@@purplepotatofarmstand no problem I hope you understood what I wrote back as sometimes I have an hard time explaining things in words. And I hope you resolve the issue your having!!

I use the ms906ts scan tablet with the mp408 scope! Did you have questions or concerns on what scan tools would best suit your needs ?

@@wrightsrrt871 am thinking buying ms909 to use it with m408 maxiscope Is that something would workout you think?

@@lusakomichael157 so far what I've researched the mp408 is only compatible with certain types of the tablets provided but some things to think about are these! A: some tablets have different capabilities than the other ones. The reason I bought the one I did is it reprograms certain things like resetting airbags or reprogramming tire sensors and is just more all around type of scanner! So not every scan tool is best suited for what you are doing! B: the oscilloscope can be ran of most PC laptops as well so you don't even need the scan tool to run mp408 scope just an laptop leaving you open to buying what scan tool best suits your needs as long as you have laptop as well that can run scope! C: depending on tablet and the model you buy it can cost more to update the tablet yearly! Basically my tablet cost $678 an year roughly to update where the ms909 cost $900 something to update so cost more. Now final thing to do buy American based autel tablets with U.S. based hardware and when I bought mine I went through Walmart! Next call autel directly and explain the uses your looking to buy the tablet for and they can help you with the one that will best suit your needs! As I bought the one I have for cost effectiveness the fact it came with an kit of obd1 adapters for older models and is advertised to tire techs and body techs or home repair or private repair. So just seemed to be an all around tablet with the lower price tag!

@@wrightsrrt871 thanks a lot for your help buddy!

@@lusakomichael157 welcome

So check fuel injectors cause when you can't find the unturned fuel smell sometimes you have an injector that's sticking open but when I have an minute and I'm back home ill look into your issues more and see what I can help you with! How many miles on jeep what make and model and have the injectors been done ?

Also check harness for shorts at the cam or crank sensor plug ends and check crank sensor for damage if it wasn't properly gapped to read right (south main auto repair channel) has a video on adjusting the gap on crank sensor. There's also crank and cam correlation that you may have to do an adaption process through scanner tool to readap them to work together depends on vehicle 😉

So I've sofare changed the cam sensor and the connector plug it had oil all over it but the p1391 code is still with me and the intermittent issue of SPUTTERING misfiring BACKFIRING and most def. Shutting off is more present know only on warm up thou I got a scam tool that read live data but idk how to check my cam and crank on it it's the Innova 3040rs scan tool I'm going to change crank sensor in a hour hop that fixes things

@@danpeterson3739 yah sounds like I would try replacing crank sensor and look for damage to it could lead you to other issues if it is. Also look into videos on gapping crank sensors properly. If not these jeeps sometimes need the harness replaced for the crank do to shorts. Now I also know this if the cam and crank sensors share the same system as the o2 sensors or mas sensor or map sensor then if any are shorted they'll all have issues as well so visually inspect your whole car or at least the sensors on that circuit. If there is an break or power steering leak those fluids can blow back onto electric and are highly corrosive and can cause shorting issues as well.

@@wrightsrrt871 okay so I did the crank sensor and you wouldn't believe this Soo when I was doing my engine swap a few months back I had both engine on the ground tried to take crank and cam from my old motor and the crank wouldn't come out on this motor I had got the bolt out but the sensor was stuck in and I said f*&+ it if it starts it works I forgot to put the crank sensor bolt back in and I didn't have issues at first but I did start having issues as the crank sensor got loose no bolt I still replaced the sensor sense I was able to know get it out and got the new sensor in and no code and no intermittent issues at all the jeep idles and drive fine and I got my gas mileage back a bit too the harness to the sensor was also fine and intact so I'm happy know can finally make it to work on time

I like the rail light more cause I use it and the magnet to place it in tight spots on the engine to do sensors or electrical and many other things but thats why I liked it as well but now I'm thinking of getting an couple different flashlights for different reasons and repairs I also use an head lamp sometimes when I need to.

@@wrightsrrt871 I use coast headlamp and have several lanterns as well as flashlights too for different uses. Headlamp XPH30R Lantern EAL22 and EAL17 Flashlight Polysteel 700, G450, XP11R

No it does not need internet but dose scan slower when not connected so if your trying to drive around and do live data you can get more real time data by hot spotting to your phone. These are not the highest end scanners that autel provides but dose most of everything you could need for an fair price like scanning, live data ,service options for bleeding abs and such along with acces to maxi fix data base to see what common fixes helped other mechanics who report there fixes to data base. My favorite part is you can program pcm moduales and other moduals as well with this model! Good day and hope this helps !

No I dose not

Welcome mam!

Useless to who just cause the video ended up backwards when I inverted the camera doesn't mean you can't open your ears and hear what the wrench is about. You sound like someone who doesn't know how to use an torque wrench or what it even is. Besides that this video was just meant to be an brief overview of what the wrench can do and not to show it off but show people that it feels to be built sturdy and I would buy this wrench for $170.00 vs an snap-on for $800.00 not to show technicians how to use something they already should know how to use. If you don't know what tools are or how to use them maybe you should not be fixing people's stuff let alone your own stuff. Aside of that if you want to be rude to people you know nothing about maybe you should not be on my channel as this is meant to help those understand that there's cheaper start-up tools then snap-on that are decent since husky is an good wrench. Also if you want to know how it functions so bad why don't you chance your money and go buy one on an wim like I did when I bought all my husky tools or are you just to cheap. Plus there's Google if you really want to read the description in detail on the tool at hand. There are many digital torque wrenches out there most functions are simular with few differences if any the only difference is price typically. Good day to you sir!

Thanks much and cheers to you as well

Yes it dose it shuts down on its own every 10 secounds and stores previous settings.

Well if you don't like the review then that's your problem and I don't give an shit what you think I could not have done one at all and there isn't another one for this particular torque wrench so you get what you get. If you want to call people stupid then stay off my Chanel.

Yah I realized it after the down load sorry I'll repost an better one of it wheni figure out what whent wrong. Thanks for the reply on it 👍