Відео

have the 2019 Bighorn. Can i just change out the low beams to Led and do i need a conversion kit or just change the bulb thats it?

So what settings will you lose. Factory or personal

hey great vid! im thinking of putting this on the exact same truck. did you end up have any ball joint or sway bar connection wear issues with this lift? thanks!

Great video. I just purchased a 2013 Crownline 21SS. It has a mag350 5.7 I’m getting ready to take it out of the water and do an oil change. The previous owner said he thinks he used 25w-50 synthetic oil. All over the internet it says to use 25w-40. I have no way to verify what’s in my boat. What would you suggest? Thanks

Teach them young...good job!

Just bought a used 2019 ram laramie with 80000 and the truck died a week later with a pdf3 code. Had the battery changed and codes removed, so far so good. I just hope that was the problem . Is this a common issue?

I'd recommend using cam buckle straps instead of ratchet straps. It makes raising and lowering the top so much smoother

Good to see you have the regular hemi. Not the e torque crap. I was able to add sound to my 21. It rocks

Why is the back of your head flat? Are you Polish? Did you donate part of your brain to science?

Terrible video

Since you didn't use high heat paint are you having any issues with the paint bubbling or coming off??

Our 5.0 probably the same

Thanks , and yes yall work good together

I just had the battery on my 2019 finally die. After shopping around, I found the Everstart Platinum H8 AGM battery at Walmart for $180. Everyone else is around $250 by me. Hopefully that helps!

It’s safer to just check running alternator voltage directly across battery terminals. 😊

nice well done video, also great father son engagement.

Just change the battery on my 2020 ram. Finally went out after 4 years. Thank you for the help

allways tighten positive cable before installing neg cable

Dad and daughter was great, but 2x4s under hard top????? NAH!!!..

😂😂😂. Son’s stronger

What mud flaps are those ?

Mine doesn’t look near as good lol, but it is working!!

hey how the battery doing is it still good. next time use the ecu memory saver it will save your codes when you remove your battery.

This is a monumental problem which Ram essentially ignored. My dealer re-sealed my brake light and comped it, however it was also leaking from the window surround which they wouldn’t comp, so I got Stellantis involved and they did pay to replace it. Truck is a 2019 with only 14,000 miles when it started leaking!

Whats a quart....?

that flag looks great. the cover just pops. and know your saving everyone 500 bucks thanks for the video.

How does it hold up to cleaning with water? Like pressure washing but not up close of course or just rinsing using a hose sprayer pressure which is a lot less than a pressure washer even at a distance? Also did you use a plastic adhesion promoter before laying down the primer as paint is known to flake off of plastics easier than panels. Thanks and turned out amazing! Teamwork makes the dream work.

Honestly I was just gonna watch a bit and move on but because I get DAD is the hero here a Gen X'er I can tell. Please continue to spread basic knowledge on the so called high tech cars lol. Thank you for explaining in such detail that does help.

Why is there no like button? Only dislike... I liked the video

Butyl tape might be a better gasket solution. YMMV…

Thanks great video

Do you have to prime the filter before installing it on the motor?

How do you check the replaced oil level? My old 5.7 must burn oil? How to top up without overfill? Thanks, greetings from Thailand.

Curious to know what the underside of the distributor cap looked like. I.e. is there a visual way I could know whether it needs to be replaced?

Thanks for making this!!

careful putting the air cleaner nut back on the carb to run it. ive seen them loosen while its running and could be ingested into the engine.

It’s not easy , just time consuming. Good job.

Any issues with flickering,canbus or DRL not working?

Great video 1 step left out that I found was to tilt the seat up while it’s plugged in. If not you can’t get to the T40 In the back other than that very easy

What if you need to take the brake light off again at some point? How difficult will it be to break this silicone bead?

Come on man eat your Wheaties I just had shoulder surgery and I can pull that ignition button off with my bad arm

Whats missing is you have to use resistors on all LED conversions for Big Horn or you get flickering or light outage. I have been through 3 sets of LEDs in under 2 years. It was such a huge pain in the butt, I went back to Xenon 6500 lights.

Make sure you check the remote start antenna that's next to the brake light that's were the water was coming in on mine

Amazing job! Nice to see great team working together

This was a great video, I had visions that the intake and half of the top of engine off. I am not the most nibble guy out there, but I can try ...... LOL JB

Got a pair and thankfully your video got me installed. Thanks!

Nice symbol! Well worth the effort!

So a lot of people say you can’t just plug the led in and that’s it, you have to get the resistor that goes b4 the bulb so it don’t strobe or flicker on you!!

Guys, guys, guys... It is soo much easier to remove the intake manifold bolts and a few other fasteners. Just slide the manifold forward a couple inches and be done with it. Never changed the gaskets. Did this in less than 45 minutes. No issues afterwards. 68K miles and pressure issue fixed. Best of luck. Was too painful to watch the entire video.

Thanks for this bro! Helped out so much