Відео

I was wondering if you could help me out here, I have a 2008 ML350, while taking out the radiator, I mistakenly pulled the AC line from the Radiator side, Freon vented out in the garage and it was not a comfortable moment. I have since not driven my car or even turned the key, it stayed in the garage but did not cover the pulled line but it stayed in the engine bay. The Compressor hoses are still connected. I am worried if I need a flush? A new condenser? Or put the hose back and go to a garage and have it recharged? Thanks for helping out.

Which side is A Circuit Low Bank?

Thank you you made it easy and simple. I have same issues my 2018 Toyota tundra

I got an error code U1454, no clue what is … some ethanol sensor.

What is the error code?

super helpful, thank you so much

Thank you. Dropping the exhaust and propellor shaft is just nuts to change a sensor. Good video.

What code was it giving? I’m having the same issues but the code is saying bank one a

I'm having a hell of a time finding a replacement line that will fit, any chance to get a link to where you purchased it?

P001685 I’m getting this code I replace intake and exhaust sensor on bank 1 a & b still giving me check engine code

is it the same location for the v6 rav 4 2007?

This is Astra from Roadanvi . We are a brand specializing in car stereos, infotainment systems, and related accessories.I would like to invite you to review our products. How should I contact you?

You need a better camera.

Good video....much help

Changed the sensor. When I finished I erased the codes and started the ignition. It started up like brand new and even when doing a test drive it preformed nicely. When I parked it, I decided to start it up one more time to make sure the error code wouldn't come up again. The same problem and error code came up. Any suggestions? I also changed the sparkplugs.

Hey my 06 mini cooper cranks up then the service engine light starts blinking and it starts shaking what causes that

worst video. all I seen was the floor

I have the same one same color its so annoying being behind the engine .so hard to get to. Thanks for the video

Couldn’t you just change control valve from button?

My seat belt on a 2008 g35x is not long enough to do that. Why do you need to tie the wheel anyway. It locks when the ignition is off. Also, what about the wire?

How easy of a job is this? IE lift the panel then a couple of bolts for the shift gearbox? I’m pretty capable doing work on a vehicle but don’t want to mess anything up. How does the center panel unlatch/lift. Are there any fasteners or do you just pry it up at fastener point? Thank you.

and now, let the rattling noise begging because you did not put the battery cover properly in the hinges. What a butchering job. But, thanks for showing the wrong way of doing it. I learned more than if it had been perfect.

WTF was it???

Nice job but it would be far easier to follow along with better camera work. You're often too close, shaking way too much, and not enough lighting and focus to actually see what's going on. Try and remember that in future videos.

This video is FANTASTIC!!! Mercedes wanted to charge me $175 just for an oul change. Thank you.

12k views and only 85 likes. What is wrong with everyone? I'm glad this video is out there. I'm going to do my own compressor job and save $2000. Thanks bro!

That give me another perspective. Trying to do one on a GLE with the M276 Bi-turbo and was on the impression I need to drop the catalytic converters. I never thought about the drive shaft. I take a look at it next time I put the vehicle on the 2 post lift. I have done it on the M113 motors and that you get it from the top on the back of the motor.

Is this switch B?

Excellent work!

Yes...unfortunately, I was not able to reproduce issue and really concerned about it occurring while on vacation. To avoid risk, had rear air suspension bags changed for peace of mind at local European shop.. Work came with 3 yr warranty

Thee is another part that look like a cv axel that sits off to the left and it attached to the controllers arm. Do you know what that is? It does look like another cv axel but I know it not but I can't figure out what its called I think i need to replace that, along with this cv axel. Tyvm btw. Now i know how to do it.

Crap

Did you watch that Casi... from your dad lol 😆

It works for 2017 Nissan versa sv ???

Thank you

Thanks for the help. Knowing to remove the gasket helped a lot.

Still looking for the 6th bolt. Thanks for the awful video man. No help.

Nice it was indeed very helpful thank you amigos👍👍👍

Dante sorry the nic name so what you did cus I'm having problems

How do you change the transmission fluid for a 2005 land Rover Range Rover

Did that and it still giving the same code

How do you know when to replace it

Can somebody please what’s the part code?

How did you remove the drive shaft?

Could you provide links to the device and solution being used here?

Thank you so much, your video is so much better than the other I looked at.

Tengo el mismo poblema

why you keep repeating the same thing over and over

Good Job Sr big help for me 👍👍👍

After replacement do you need to calibrate it.