Відео

How long until they fogged up the lens?

You were working on an updated harness. Is it done?

Hey, installed the harness and now my clutch temperature indicator is blinking… what going on? Also the check engine light is on.

Does anyone know how to find parts for that back flap on the tailgate? I’ve looked everywhere and can’t find the parts for this cover. The previous owner closed the tailgate and has mangled mine

I have to open it to shut the tailgate is the deal breaker, but nice cover and slightly cheaper than G2

Great job. But why did you run your return line to the back and not tap into the front? Just asking thank for the video is it worth it to have heat?

Do you have to take the tires off or no?

Like exactly on point

Mine looks identical to yours

Exactly what I was looking for. Thanks!

Will this system work with a bed extender?

what is the tread pitch on the lower bolt on the knuckle?

Did you hook up the drainage tubes at the front ? I have a bed liner and not sure how that’s going to work

Hi Jason, Thanks for doing this great video. We shared it on the Inferno Cab Heaters Facebook page today. Thanks again!

Man, I was loving your content - Curious, why did you quit uploading? Did you sell your Talon?

Don’t buy there stuff I ordered a set of radius rods in October and it was cold so I went to install them on Saturday and there employees gave me the wrong bushings I was told they would not make it right I was to pay for there mistake over a 20$ part !!!!!!! Right to ZRP I go !!!!!! This story will be told to everyone I know for sure !!!! 

Hello, Are you interested in testing our products? We would like to invite you to test the Scratch-Resistant Windshield for your 2017 RZR XP 1000

Let us know how it works. Thanks

The smarter safer way to test for binding is to spin the wheel by hand.

Is thr talon loud interior wise ? I havw the wolverine now and its pretty loud

How did you make the two spring suspension?

I just recently purchased a brand new talon r1000-4. I know your videos are 3 to 4 years old and that you have sold this talon a long time ago. I have been watching all your old videos. You install the best aftermarket/oem accessories, but only have videos on some of them. What extended fender flares did you have on this talon? You stated the shock thearpy springs was your best upgrade. I couldnt believe you bought the upper doors then changed out the cage. Buy a new sxs and start doing some videos! Great job!

I wish you guys would stop skipping the process for the drl lights. It would have been helpful to video the actual process.

does this work for a 4 door?

Hello I know this video has been out a while, do you know if I just install a fuse relay box to the winch cables, do the relays cut power to the rocker switches or do I need a kill switch tied in? I am trying to wire the speakers and light bar onto a bigger fuse and leave the rock lights and whip lights on the pre wires accessory harness without having to add another battery.

Need to find a bottom base for the Packout stuff for the bottom of the YETI. Anyone see that anyplace?

That blue plug where do you get that harness your using for key on power

Great video. Thank you!

Unable to find it

Are you making any more videos??

Thank you. You just saved me a lot of headache figuring this out on my own. How do you like the headlights??? My third set of aftermarket ones and decided to spend the money (500) and get a real nice set. Do they live up to the price???? No moisture? No chipping on housings???

Can you install aftermarket exhaust without tunning or you need to tune it before install thanks.

Where did I get one of those books?!

Hey Jason. I ran a set of LED cube lights on my Pioneer using the OEM backup beeper harness. The cube light at some point had an issue and because of the ground being used to make and break the circuit, caused the computer to get confused about what gear the transmission was in and would go into limp mode. Lesson learned, buy higher quality LED lights.

I want to see what wire they tap off of from that 8 pin connector plug you purchased . I think it is the gray wire that is spliced into. I made my own reverse switch that will handle a hi watt lights for reverse light and side lights , etc without tapping into the trans harness. I used a Much higher rated switch and lighted up my center column where the gear shifter is . Thanks for the video .

I am a deer hunter. Would a gun case fit using the extender. Could you provide a diagonal measurement? Thank you!!

Do you still have the rear triangle shape fabric and if so would you like to sell them

i think his oversize tires are taking some "performance " away, clutch kit or not , bigger tires in theory would give you more top end less bottom end, on a gear or shaft driven but with belt / torque converter, (too many variables to list) the bigger tires not only add weight but also more power to turn ect.rpms curve is different with different sized tires ect. ect,. i would say if he had same size tires on both and same clutching ect he would've gapped more shorthand

I had a soft flip on a 2019 ranger and never had any water come into the bed. I now have a 2023 Ranger with the ford hard fold and water leaks in so much I do not want to put my beg rug in. water drains down the rail in the rear, you can see the rail is open and water drips into the rear of the bed. The folds are always moist and drip water into the bed. The closing of the gate is also an issue with me as mentioned, my soft top was not a issue. hope this helps someone.

i have same truck and cover wondering if i can install a backrack with this cover and if yes can i still flip all the panels up to use the whole bed

where did you get the wiring harness?

Did you do the full lock test before the rack? The i4WD could very easily be programmed to turn off the inside wheel on a sharp turn to help it turn.

Super helpful video man. Much appreciated

How do u like the spray in bed liner?

I'm going to try this. The 'official' particle separators are expensive enough I would rather just keep replacing the OEM filter. Anyway if this gets to be a hassle then I might try rigging up some external snorkel and putting the filter outside the box. If I get to dislike that I might get a small tractor pre filter. I used to drive a wheat combine and it was the dustiest job of all time. We had a pre filter on it and it did a pretty good job. I can probably buy a small one for about $40 however I don't think I will need to.

I have the exact same cover and had it installed by dealer ($1400) when I bought my 2019 supercrew and over time... i hate it. Having to lift it every time I close the tail gate is a PITA. Its also counter intuitive to fold as you have to pull down on the cable release while you pull up on the cover...another PITA. I have heard theyh made a design change so that you no longer have to lift to close tail gate. I found your post while searching for info on that update. Glad you like yours but as mentioned im sick of mine.

I had someone give me an Honda pen aluminum bumper but if doesn’t have the struts that the winch mounts to. Any idea if they can be purchased separately

have you had any problems without running a 2nd battery? is the stock battery keeping up with everything?

Update video?

Thanks!