Відео

😅

This helps thanks

This is a very good video in regard to actually showing the steps you took. And how you actually put the wires back together.

Great video. 🫵😎🫵 Really appreciate it !!! Thx

my motor cable is stuck due to some white silicon and out ng es no getting it out without a BIG fight

Thank you. So one of my hub motor wires got cut and I have no throttle response. I don't know if running the bike previously with wire cut destroyed the controller or just hub motor.

Informative vid thank you. What type of cable did you use as a replacement, what gauge was it?

I took my wheel apart to do the same repair. I had no power to my blue phase wire using power tester same motor as what you worked on. now it's apart & i have continuity on all the wires so it could be in the rotor winding??

Hi - Do you have a link for the "tree clamp"? Did I spell it correctly? Thanks!

I might need to do this soon. My wires are on the end of their life. The part of my bike frame which holds the wheel axle, got so bent open, this twisted the wires almost enough to rip them out. Bad design of the bike frame, not designed to be modded into an ebike.

I didn’t get any punctures on my fat bike. maybe my tyres are thick too

I’ve been looking at all videos about rewiring e-bike hub motors & can’t find 1 which shows exactly where each phase wire attaches inside the hub. Obviously like for like reattachment as per hall sensor wiring but my problem is that i had an axle spinout on my Dapu M155, after which the motor has not worked. the yellow phase wire is not attached....display shows o.o speed and PAS 0. the lights also won’t switch on; after 10mins the display shows 33 the switches off...any ideas appreciated category: dapu m155 rear disk brake gearbox: planetary gearbox with freewheel type: bldc motor (brushless direct current) power: nominal 250 w (maximal 400 w for rotation sensor, 500 w for torque sensor) used bb set: ncte sbbrf - rotation sensor ncte sbbrt - torque-rotation sensor

Are all motors cables 9 pins and what the 7 pins functions beside the vdc+ and GND, I need to remove my disc break and there no way without cutting the motor cable a otherwise I need to remove the battery case. How it should be done? Should I cut it and reconnect it?

Great video. Question. My ebike works fine, but when I do the motor phase wire test and turn wheel (backwards) for resistance I don't get any but motor works fine and hall sensors work fine. This is not normal but it hasn't caused problems. And ideas why? /bklyn 👑

I just needed to see how to remove the wires from the inside the axel but you completely skipped that part so maybe I'll just pull on it harder lol thanks

i dont think we going to get any answers this guy is gone.

Can you show me how to fix mine for my electric pride fat tire e bike....got few rips in my wire

Hey does anyone know what those wires are called? My wires got stripped near the axle and i can't buy the wire without the motor..I know its the phase wire but I can't find any online for a brushless motor..

Where can I source the wire?

Where did you get the wire? You can't repair these motors because no one knows where to get the wire?

Where can I get one of those clamps?

Where can I buy replacement cable?

Excellent video very well explained,thank you .

Nice video man! 👍🏻 I wonder if Daymak hub motors are this easy!

Great video. Have you ever rewired a geared hub motor? Thanks

Hi. Are you based in the U.S.? Do you have a bike shop? I have the same problem. My hub motor cables are ruined primarily because I have been riding without a torque arm. The rear hub motor twisted sometimes while I was riding and ruined the hub motor wires I had a very hard time finding a torque arm in bike stores

Which brand and model of tire?

hi worked on brother ebikes so many time the cable is the main thing on ebikes that goes bad tip you will need to save up for cells over time s the life of them goes down over time

Thank you. I hope my repair goes as smooth as yours seemed to.

Thanks , just what I needed !

Hi where do you buy the replacement wire and what is the replacement wire called also the connectors to the replacement wire?

what wire did you replace that with?

Im thinking of getting this bike too! Yes anything over 15mph is illegal as you would need MOT, license and insurance. Just get a Dahon p8 and motorize it using the magic pie 3 kits and convert it yourself. That's what im gona do!

There are so few full suspension folding bikes on the market! But it's necessary for high speeds that electrodrive provides. So Dahon's bike is one of a few to choose from. Good-looking one). Btw, do you remove batteries when fold the bike? If yes, is it fast and easy?

hey, thats cool! did you convert the bike? isnt it ileagal in UK more than 250W?lol