![Justin S](/img/default-banner.jpg)
- 25
- 3 130 351
Justin S
Приєднався 1 гру 2009
Valvetronic Designs Universal Muffler on a Dodge Durango
Valvetronic Designs Universal Muffler on a Dodge Durango
Переглядів: 48
Відео
Valvetronic Muffler on a 1998 Dodge Durango with a 5.2L
Переглядів 6623 місяці тому
Valvetronic Muffler on a 1998 Dodge Durango with a 5.2L
Crazy Burnout!!! 2013 Mercedes-Benz C63 AMG
Переглядів 2033 роки тому
Crazy Burnout!!! 2013 Mercedes-Benz C63 AMG
EASY Arrma Big Rock V3 BLX Battery Installation!
Переглядів 3,8 тис.3 роки тому
This little trick by moving the straps can save you much time and frustration.
2013 Dodge Challenger Window Drop Feature Causing Dead Battery Overnight
Переглядів 2,3 тис.4 роки тому
2013 Dodge Challenger Window Drop Feature Causing Dead Battery Overnight
2009 Chevy Traverse gets a plug and coil.
Переглядів 10 тис.5 років тому
Customer was advised a full set of plugs but declined due to lack of funds.
2008 Mercury Mariner No Crank - Diagnosis
Переглядів 31 тис.5 років тому
2008 Mercury Mariner No Crank - Diagnosis
Rodent damage wire repair.
Переглядів 1,2 тис.6 років тому
On an equinox, the check engine light was on for high voltage on the fuel pressure sensor circuit. I found the purple wire chewed through on the harness near the sensor. Here I replace the missing section of wire and re-insulate another wire in the damaged area.
Pickle Jar Brake Bleeder
Переглядів 2397 років тому
Here I made a vacuum brake bleeder using a pickle jar, some fittings and hose, and knowledge of how a venturi works. Don't spend hundreds on a name brand vacuum bleeder when it is so simple to make. If I get requests on how I made it I will make another video explaining it.
Welding Rust!!!
Переглядів 237 років тому
The third attempt was a charm. My ground clamp was in a bad spot twice! But i had to stop recording because my phone was gonne melt!
Bearing race removal in ten seconds.
Переглядів 13 тис.8 років тому
Bearing race removal in ten seconds.
2006 FORD EXPLORER REAR AXLE REMOVAL
Переглядів 50 тис.9 років тому
2006 FORD EXPLORER REAR AXLE REMOVAL
2005 Cobalt Supercharged Boost Gauge 19 PSI
Переглядів 6 тис.14 років тому
2005 Cobalt Supercharged Boost Gauge 19 PSI
ZZP Cobalt SS on the dyno 241hp 239tq 2.7 inch pulley
Переглядів 12 тис.14 років тому
ZZP Cobalt SS on the dyno 241hp 239tq 2.7 inch pulley
Where did you get it?
Search up Valvetronic Designs. Ordered right from their website.
Check out my other video here! ua-cam.com/video/k5g_736DJ6s/v-deo.htmlsi=PRnAMHGO0G-hQmhF
Sweet
Currently going thru this
I bought a new switch and I still don't get any cranks, no start. Do you have any idea what I am facing?
Hahah! I was so frustrated with these straps. You see this video and it’s like duh! Thank you!
My 2005 is doing the same thing, i install a new starter it still does not start, what did you change, is it the ignition switch, if yes did you install it your self does it need to be program after instalation? Thanks
Thank u so much
I swear I just started my car
Dam they must charge allot....for that work there...
Would be nice to actually see what is being replaced.
I followed this video and thank you it helped me. However, now I am starting my car like this for the last 2 years 😂 Maybe it is time to take it to the dealership for permanent fix which I don't know if the lock cylinder needs to be replaced or what.
Worse instructional video I have ever seen on UA-cam🥺.
I believe no crank also happens if the ignition fuse is blown (correct me if I’m wrong). That might be worth checking first for anyone having this issue
Which could did u buy???
Alright so what does it mean if it doesn't start it cuz I bought a brand new switch and it does the same thing
Did you get it fixed or figured out? I’m having the same troubles with my 2010 mariner
No i never did get a chance to figure it out
Same here. I replace the stupid switch and it still won't start.
Sure, we "could" do that, but then we miss the fun of angle grinders and air hammers, plus you didn't leave any grooves or gouges for the next guy.
Can you jump start it to work
What if using a screw driver work for a little while and then it stopped starting all together?
What size battery and brand do you use bc I was told an 8000 won't fit in a big rock?
This is indeed a 8000 in a big rock. Fits without modification.
I was told 8000 can be too much time 🤷🏻overheating? I have 3 power hobbies 5400 100C
Is there a way to clean the switch or get it to sit more firmly in place? I did the removal, did the screwdriver, worked, but when I click it back into place i can start it as long as my finger is on it kinda holding it in closer contact maybe? When I put it all back together, I can stick my thumb up underneath and push the switch a bit and start it right up.
Did you find a solution for this?
Should I get a 8000mah 3s lipo or two 5200mah lipos
two 5200 without question imo
Really late on this. But some cams will put you right under 300 if not over. Your pulley is way too small for your mod list
Coil order?
"Bubba, I think someone forgot to close the door"
Doesn't help unfortunately
👍
Does it work on an 05 mariner?
Yes
Mine is not turning on I don't know what the hell the problem is
My chisels thank you.
消化器に向かってファイアしてるのはやばやば
Pretty damn slick
Nice! I'm adding that to my bag of tricks.
ハブベアリングのアウターが残っちゃったから膨張させて取ってる
That will be $ 200.00 sir
My mind just blew. Thank You this will save me a lot of time.
That was tricky dick 😎👍
Yesser
Roger
Yup
3 second tig run is faster. 1...2...PINK!!!!
Cool
You gotta be kidding me! I don’t think this works in Michigan. Lol! Wow. Cool video.
It works in Vermont
@@BLACKSSG85 That's all that matters, brother.
Mf I with I seen this yrs ago
Direto ao ponto...
Ниху...я се буду знать
Holy crap. Nice !
Eu fasso isso na minha oficina
ایول رجب
It's magic Wala 🎇.
Old boy has done that a time or two...