- 38
- 296 608
quick automotive diagnostics
Приєднався 28 жов 2018
CHRYSLER 300 OCCUPANT CLASIFICATION MODULE FAULT.
This Chrysler had a failed weight sensor that pulled down the communication Bus CAN B for the OCM module. Very strange case and new case for me. Apparently you can use and used wait sensor and replace the damaged one if this happen to you.
Переглядів: 9
Відео
VOLVO XC60 B00791B, B007A1B
Переглядів 2242 місяці тому
This Volvo xc60 has a hidden pretensioner that is bypassed from the factory. Is this safe?
JEEP CHEROKEE HOOD SWITCH AND AMBIENT TEMP SENSOR PART 2
Переглядів 983 місяці тому
THIS PART OF THE VIDEO IS FOR THE WIRES THAT WERE DAMAGED FROM THE FRONT END COLLUSION .
2019 JEEP CHEROKEE ODOMETER BLINKING FIXED PART 1
Переглядів 4463 місяці тому
THIS CHEROKEE HAD A BLINKING ODOMETER AND IT WAS FIXED. DONT FORGET TO WATCH PART 2 TO SEE WHAT HAPPENED WITH HOOD SWITCH AND AMBIENT TEMPERATURE SENSOR CODES. ENJOY THE SHOW. SUBSCRIBE AND LIKE THE VIDEO
MERCEDES BENZ C300 RADAR SENSOR FAULT
Переглядів 2,3 тис.4 місяці тому
THIS MERCEDES BENZ HAD A PROBLEM WITH THE FRONT COLLISION RADAR SENSOR. NO COMMUNICATION WITH THE SENSOR DUE TO BROKEN POWER WIRE AND BROKEN COMMUNICATION WIRE AT THE MAIN DISCONNECT CONNECTOR RIGHT SIDE OF THE FRONT PUMPER. THIS IS A VERY GOOD PLACE TO LOOK AT FIRST IF YOU ARE EXPERIENCING THIS KIND OF COMMUNICATION PROBLEM WITH FRONT RADAR ON THESE C300 MERCEDES BENZ.
DODGE RAM 6.7L DIESEL PCM SHORTED
Переглядів 825 місяців тому
2010 DODGE RAM 6.7 L DIESEL WAS BLOWING THE PCM MAIN FUSE IN THE TIPM. AFTER A DIAGNOSES WE FOUND THAT THE SHORT WAS COMING FROM THE PCM. WE OPENED THE PCM AND TESTED ALL ELECTRONIC COMPONENTS. WE FOUND THAT THE INJECTOR CAPACITOR WAS LEAKING AND SHORTED INTERNALY CAUSING THE FUSE TO BLOW ALL THE TIME. THANKS FOR WATCHING AND DON'T FORGET TO SUBSCRIBE TO MY CHANNEL.
HONDA CIVIC P101A
Переглядів 3716 місяців тому
THIS HONDA CAME FROM THE DEAL WITH LOTS OF DASH LIGHTS. A BAD EXHAUST SOLENOID CAUSING LOTS OF TROUBLE CODES AND CHECK ENGINE LIGHT EVEN POWER REDUCED. NOTE: I did some modification that was requested my the customer. This video was deleted and re-uploaded after miner modification requested by the customer. Thanks for watching.
2009 JEEP PATRIOT NO CRANK NO START
Переглядів 2,1 тис.9 місяців тому
@quickautomotivediagnostics8728 JEEP NO CRANK NO START
NISSAN ALTIMA 2.5L NO THROTTLE
Переглядів 5 тис.Рік тому
This Nissan had no throttle response after a front collision. The PCM was bad and after replacing the PCM the reference voltage came back. Now we lean that if you disconnect the Canister pressure sensor the PCM will cut the 5 V reference at the throttle accelerator pedal . We also lean that the connector inside the accelerator pedal sensor can be loose. I soldered the connector and that fixed t...
DODGE JOURNEY NO BUS
Переглядів 1,6 тис.Рік тому
THIS DOSGE JOURNEY HAD NO BUS NO COMMUNICATION. FOUND STAR BAR SOLDERING PINS BROKEN.
KIA RONDO NO RADIO NO DLC POWER NO REMONTE
Переглядів 5362 роки тому
KIA RONDO NO RADIO NO DLC POWER NO REMONTE
CHEVROLET FUEL AND TEMPERATURE GAUGES DOWN
Переглядів 1282 роки тому
CHEVROLET FUEL AND TEMPERATURE GAUGES DOWN
GMC YUKON XL TRANFER CASE FAULT C306,C0392, C0396
Переглядів 4,8 тис.2 роки тому
GMC YUKON XL TRANFER CASE FAULT C306,C0392, C0396
CHEVY CRUZE PCV KIT FIXED THE CRUZE PROBLEM
Переглядів 20 тис.2 роки тому
CHEVY CRUZE PCV KIT FIXED THE CRUZE PROBLEM
TOYOTA RAV4 PASSENGE CLASIFICATION MODULE FAULT
Переглядів 492 роки тому
TOYOTA RAV4 PASSENGE CLASIFICATION MODULE FAULT
SUBARU FORESTER STEERING ANGLE SENSOR CALIBRATION
Переглядів 18 тис.3 роки тому
SUBARU FORESTER STEERING ANGLE SENSOR CALIBRATION
DODGE PROMASTER ODOMETER BLINKS FIXED
Переглядів 16 тис.3 роки тому
DODGE PROMASTER ODOMETER BLINKS FIXED
HYUNDAI CLUSTER GAUGES FAIL BECAUSE OF CAN BUS
Переглядів 2,6 тис.3 роки тому
HYUNDAI CLUSTER GAUGES FAIL BECAUSE OF CAN BUS
After you did your radio work?
Every time you replace any module on new dodge, you need to perform proxy alignment.
Who can help me poxy Aliment @quickautomotivediagnostics8728
@@Lovelydavid399 yes the Radio worked fine
I need technician
What kind of Tech you are looking for?
My mile was blinking and radio doesn't work
I need help bro
How much for the part?
I don’t know the price. Sorry
@@quickautomotivediagnostics8728 do you know where I can find this part? I cant find it anywhere
This happens to the G35 too.Would you know if the M35 Yaw sensor fit the G35 ,as in capability wise!
Very useful video, thank you
I saw the same in my 2017 nissan Sentra today and i came over ur video, i guess i will have to go to nissan but the car still start 😢
We all drop stuff as mechanics. I was in the Air Force and the U-2 pilot had a bad altimeter. He was strapped in I reached over him to unscrew 4 screws and I dropped a screw. That scrubbed the mission and we had to pull the ejection seat out and part of the floor board to find the screw. So chit happens
Great job ❤❤❤❤❤ can you give me your link l want learn more
@@andersonchimukono8498 thanks 🙏
Why the car is so dirty? I had problem of car saying that key is not in range. Problem was in 12 v battery the voltage was low around 9 V. Once I charged it to 12.5V all was OK!!!!!
but any diagnosis tool do that
Yes
am so appreciative for your lecture. thank you so much
GREAT MAN... THANKS BRO... 😎😎😎
just did this and luckily I had already ordered a new PCV Hose for this car months earlier. Lucky I did because the valve in the bottom part.( near the turbo) eas completely gone. When you take that hose off if you can blow air from that bottom part then the valve is missing. On the new one when you look in that bottom part of that hose connector, you can clearly see the orange valve. You can actually suck through but you shouldn’t be able to blow through it. I simply took the new PCV hose. I got and cut the ends of it off to use instead of the old one. Not expensive at all on eBay or wherever anyways, I think this is something important people should know. If you did it without replacing the bottom part of that hose then you are probably missing that valve also. Should be easily remedied and replaced.
Niice video. Thx to you I had no problems. Made sure that jb weld was on too… thx
I have a issue with a 02 nissan sentra se r spec v it sometimes loses throttle response while driving i quickly shut it off and then start it back up and works fine wat can that be
Penso que no meu caso não seja essa a solução, pois o meu comando só deixou de funcionar após a substituição da bateria. E o segundo comando funciona perfeitamente, no entanto o comando principal nem sequer abre as portas. Isto só aconteceu após a substituição da bateria.
Maybe your case needs key programming. Check with your local locksmith.
Tenho o mesmo problema, mas o meu comando só deu erro após a substituição da bateria do comando. Após a substituição da pilha, o comando nem sequer fecha e abre as portas. No entanto dentro do carro, após várias tentativas ele acaba por trabalhar, mas dá sempre o mesmo erro.
But my second Key works fine.
Oi tudo bem ?? Acabei de comprar um Nissan desse modelo usado mas tô mt confuso sobre algumas funções do painel q estão aparecendo , vc poderia me ajudar ? Até que enfim alguém q fala português 😭😭😭
is work in opel meriva b 1.4 turbo 120hp year 2012 engine code b14nel ? ? ?
Not sure check with the kit supplier.
good video. thanks for sharing.
you are welcome😀
Were did you buy the original iprog.
Just online AliExpress.
Hi thanks for the video I have the same problem but after a few times it will start Is any way I can connect with you thanks I’m in manitoba to thank you
Yes you can connect with me by visiting my website site or use good type in Quick Automotive Diagnostics.
ITS 2021
Thank you. I am facing the same problem now. Do you mean that you took the connector out? Just wonder how did you connected the two ends of each wire. By the way, I ever measured the resistance between green wire and yellow/green wire. The reading was 57 ohms. It indicates some continuity between the two lines. Is it normal or not? Your response will be appreciated.
THANK U SUR IHAVE SAME FAULT ON QASHQAI J12 BUT I DONT HAVE WIRIN DIAGRAME FOR STARTER RELEAY CAN U PLEASE GIVE IT TO ME ILL BE THANKFUL
Sorry for the late response, what year is your Nissan ?
@@quickautomotivediagnostics8728 ITS 2021 SUR
@@quickautomotivediagnostics8728 its j12 2021
@@quickautomotivediagnostics8728 ITS 2021
@@quickautomotivediagnostics8728 2023
💐 "Promosm"
Smh sooooo if we don't have program we out of luck. What a waste of time
You need a GM Tech2 tool and you should be ok.
Thank you for your video
My pleasure 😇.
De donde saco la válvula pcv que instalo cual le puso
Hey thanks for the video i got a 2022 VW Polo automatic but when i start not crank or start but is showing key not detected hold key next to intended surface. vehicle wallet where is that???
Look behind the glove box first
I can see it but i cant touch it , how do you get it out?
You’re supposed to let the JB Weld cure for at least 15 hours ( a little more if the temperature is cooler ) before reconnecting the fitting on top of the hole. 24 hours to be fully cured. When you put 5he replacement valve cover on I hope you put RTV in the “ cracks” on the passenger side of surface the valve cover sits on or you will have an oil leak ( UA-cam replacing a valve cover on a Cruze ( Encore, Trax, Sonic ). The 2019 Encore has a different attachment point on the turbo end. There’s actually an outlet 90 degree bends and it attaches to the turbo intake tube that comes from the air filter box.
You blew it on the check valve. The longer piece of tubing is put on first and the shorter piece of tubing goes at the. Other end as the fitting on that end is slightly pointed down as the check valve needs to be slightly pointed down also.
I hope you can upload a new video about problem ' key system error' Nissan Navara 2021 > how to fix it.
What's the fuse that goes to that control unit? I'm just wondering whether pulling the fuse might do the job to reset it rather than removing the glove box (which I would like to avoid)?
I don’t remember which fuse was for the power supply
Thanks for this video. Frustrating dealing with this issue. Will try what you have demonstrated.
Good luck Sir
Thank you from the bottom of my heart, your smart friend from Iraq. My problem is with the Nissan Sentra 👍🙏
He Haw for the win. That is the difference from the DUI repair and a trained and experienced professional. DUI people I love for at least trying. DUI people do not have the resources of the accurate wiring diagrams that follow the schematic. Not a difficult problem to begin with. Thanks, the old school guy.
Good day sir I have the same problem but only problem is that key error shows car starts normal but parking brake light is flashing and car not engaging in to gear, any idea I will highly appreciate your input🙏
Finding problem = 4 hours , fix the problem 2 minutes. Thank you for saving us so much time.
I am happy that I helped you out.
I didnt need help. I just appriciated the effort from you :-) @@quickautomotivediagnostics8728
THE IDEAL SEEMS A BIT HIGH ,, BUT I GUESS THAT IS ANOTHER PROBLEM THANKS FOR YOUR TIME !!!
I did some modification that was requested my the customer.
I have a 2010 vw Passat with a key problem message center said key is out of range do you have any suggestions on that
Make sure the key is in good condition. Check the key battery 🪫
Hello I’m having the same problem on my 09 Yukon hybrid there was 3 dogs who ran under my front bumper now it’s not starting do you think I should take it to a shop to do this procedure I’d have to tow it to do so thanks 🙏🏼
Yes you need to take it to a shop where they will do this procedure to get it started again. Thanks for your questions and please subscribe
What did you pay for, a 24 hour access, this VIN only, ?????
I Always have access of 3 days for multiple vin per purchase.
I really like your channel bro but pls keep your videos to around 20 minutes, lots of wasted talking and running around here, edit out the phone calls and other non related stuff and the long moments with no talking please. You are saying that the owner could have found that problem with a wire diagram but you as a professional made a 36 minute video for a 15 minute job, THUMBS UP
Or, YOU could simply fast forward to the part(s) you want, and let that, be that!😊
@@ctgosey69 What are the UA-cam rules for paying a content provider if we do not watch the entire video?
Hi went on a trip today with my 2012 dodge journey and it gave me a no bus, engine stopped 4 times on me. I have a question if you don't mind, does it matter where you plug each connector along those little bars. Are they all the same along the bar
No they are not the same . The green should be in its place and the brown should be in it place. The connector should also be connected where they are supposed to be connected.
Thank you your video is very good and helpful. I took them out and am about to check them. I will let you know how it turns out
Ok I touched up the solder points along each bar and reinstalled them. The car is running so I am going to let it run and see what happens
Is all viewers getting beer for fixing your vehicle? 😂
I took the car out for about 3 and a half hours today and did not have any problems. It ran the whole time. Thank you so much best vid on the net for this problem.
Would that make your car “transmission slip” when you step on the gas ?
Try changing your transmission fluid and filter
@@steviethomas3233 thanks will do 💪🏽
Change the battery in the remote it will start right up
This did not work for me
I'll say this. I was about to take my car to the junkyard because all the mechanics gave up on it. No one could fix it untill I saw this video. I fixed it myself I didn't bother souldering the bus connector I just got a new one for 80$. GOOD JOB SIR.
I am glad I help. This is my goal Sir. Thank you 🙏
Your the man!
Hello, where did you buy them or how do I look for them? yesterday I had that error
Just bought a journey from a friend because of this exact issue. Love that it is such a simple fix ....once found. Thanks!
I am having trouble with my dodge journey, it shot off as I was driving 2 different times and it wouldn’t start, i left it alone for like 10min, and then it started back up. and I get codes u0002-88, u0100 and u0101, the battery was recently replaced, I’m hoping it is just a loose wire somewhere by the battery. I’m gonna have to do some troubleshooting. Thanks for your video it’s the only one that has given me a place to look 🤘🏼👀👍🏼
Awesome work brother. Im dealing with a no crank on the same car. I appreciate you taking the time to make the video.
Thanks 🙏
@@quickautomotivediagnostics8728 had to come back and thank you again. I just fixed 2 jeep Patriots with this exact issue. The wire was broken in a different spot inside the wheel well though. Keep up the videos
I looked around UA-cam and you're video was spot on.
@@centennialfarm11 thanks for the feedback, please subscribe for more videos alerts. More on the way I have a 2014 Jeep patriot crank no start with lots of part thrown on it. Coming soon
Have same problem with my 07 Patriot, I will diagnose the same as you did. What program du you use to show tha connector chart on the screen?😊