Відео

I’m getting an OHH due to the circulation pump not turning on… The pump works when on the other pump circuit. Do I need to replace the board? I’m not experienced at replacing relays or soldering

I have a balboa icon 15 spa pack that I believe went out. The top side controls were acting up and not displaying properly and now it won't turn on at all. I am thinking about replacing the pack and top controls. Should I do retro fit or try to find a balboa pack. If going with Balboa which one do I get?

My AIO waterpump is making the same noise but i guess is the rotor hitting the stator case

Hello i have sundance with the same filter type you explained on the first one, now on my question , is this filter supposed to rotate when the hot tub is being used or running, or just sits ? Mine sits , thank you

I have almost the same problem, but for me, the second relay has no output voltage. It's like the relay isn't closing... Any ideas?

replaced heater elament and both sensors still getting a balance sensor code and no heat any help will be great

I have two (2) circulating pumps, does this controller has power for two pumps? Interested of buying one to retrofit my spa. Thanks.

Do you know the maximum tow weight? i want to tow a light trailer.

As a diagnostic step, could you block the drain from inside the spa, and then check if that stops water level from dropping?

Hi thank you so much for your very helpful videos so easy to follow. We discovered that our terminal block was fried on one corner thus melting the plastic and therefore the hot tub stopped working. I'm wondering is there any point in replacing the terminal block or do you think there's a chance it may typically have damaged the rest of the board.? I can send a photo to you. If you wouldn't mind taking a look at the photo .. I would appreciate it as it could save us a lot of money. 👍

Learned something today - Billy you are the Guru

Can Iadd that to my island spa

Do they get thin and leak ?

Are there gaskets or silicone? I need to brought by and get one .. can I get your#?

HeySpa guy, Got any island spa artesian ones ?

Just a suggestion when using spray foam in an aerosol can, its meant to be held inverted (upside down). I think you will find it works much better this way and you will get all the available material out as well.

Thanks for your video. Where can i buy this Front LIP to fit my 2004 Porsche 911 Twin Turbo 996 Cabriolet?

Can you tel me on the left to the pressure switch what is le device just to the left with the 2 wires?

This part number comes up as a 997 part...is that right?

love your videos, thanks

Can I use a couple drops of super glue to hold the black gasket in place ? Mine keeps falling out of place when putting back together.

Life saver!! Thank you!!

Cord plug Breaker keeps tripping off

I have a jet nozzle in my spa that looks just line this but it is 9” across. Do you have any information on where I might get one of those or get parts to repair it because it’s not working.

What’s happening if you jumper the switch and are still getting the dashes

Thanks, you saved me $360. A spa repair guy wanted $360 for the first hour and $130 for every hour after that.

Will a cmp jet go in a waterways housing? It’s very hard to find the waterways snap in jets as they have been discontinued

Thank you

Hi, is there any adapters so to speak to connect old style ozone, light, pumps, audio plug's to updated plugs on a brand new control box? I.e. if the old box has 4 pins and the new one is a 3 pin pattern.... Or no? Thank you in advance

Can I hear you to come to Chesterton Indiana I have a 2014 envoy hot springs and it's leaking from somewhere not a lot but it's leaking

I have a hot tub project. It was at our house when we bought it. The hot tub is in pieces. We're not sure what brand it is. We don't even know if the parts we have are for it. I just built a new surround for it. Now we're trying to figure out what we need to get it running. We're also interested in adding led lights and more jets. The tub does hold water. We really want to be able to start using it.

Thank you !

Thank you, saved me a boatload of time and money!

I just replaced the heater element and reconnected everything. Tub worked great for a couple of weeks then I noticed the electrical burn smell. Opened it up and both power points left and right are burned on the circuit board. Looks like the copper leads are toast as well and the heater point ceramics are burnt. Is this really from a poor tightening on the board and/or the heat element? The tub still worked but the damage looks like I need a whole heater assembly now and if I can't fix the circuit board that is a whole lot of money.

My toggle leaked at day one. Dissasembled, filed a groove deeper for one of the posts on the switch (filed the white cage) now the grey post sits flush. Prior it was protruding past the white cage and not allowing the clear seal to seal or the black flapper valve to seal. Heard air leaking out of the switch and air constantly flowing out of jets. Along with the switch feeling mushy. Thanks Spa Guy, saved me from having to deal with warranty B.S.!

Very Good Video. I have a Air Blower that looks like that one... cannot read the data plate due to fading. I cuts off after about 2 minutes of operation, never trips a breaker. Are there thermal overload devices inside of these air blowers?

I get the sn code on mine my spa does nothing no motor no nothing the jets click when i hit the button but the motor does nothing so i replaced both sensors an it does the same thing power on an nothing goes to pr for 5 min then 2 lines for a few min the says the temp of water an then sn code no motor turns on

How the hell do you get the bi pass valves out? Mines broken and I can’t get the thing out once unscrewed. Also if you have low flo (like mine) it could be this has broken and the flap is in the pipe.

what size oil filter pliers?

Question? (Filter canister) what would you think about using gaskets(maybe rubber) or plumbers putty for the underside ring nut and on topside lip where it sits on and maybe just a small amout of silicone added to it? when I pulled the old one out , it seemed to have either plumbers putty or a gasket. what are the pro's and con's

Good video. But what’s a “Boxter”?

Perfect! Now let me go and get one of these! The back of my house is similar to yours, and you demonstrated the latest version of the 18’ wand.

I was wondering the name brand of the pipe cutter you used trying to find one that will fit that size pipe comfortably

Another happy customer…..thank you so much

What front bumper is that? Do you have a link?

The fuse worked for me. Thanks! On my 2019 JL it was F97 not J97.

Wish they kept those open relays. Now have to replace the whole board because a POS $12 relay broke

My friend! Recently my hot tub stopped heating. I confirmed the heater was OK and moved to the controller. O found that there was the same phase of 120V on both sides of the heater meaning no power to the heater. What would cause this? A bad relay or a bad solder joint? What is the easiest way to check/confirm? Where might a source a relay? Thanks!

Thank you!!

I have an old Sundance Spa Lounger, The control circuit board motor jet relay got burned as well as the air blower motor. @220 -240 volts power to it ..and the water heater is sitting above the water pump..Will this Retrofit Modpack will work. The water heater has a stainless steel curbed tubing at inlet end ..It is 6kw High Flow heater on it.