Відео

Ahahah ))) It takes time to cool down. I am just not patient person :D

I just couldn't, because with this lens optics, I would only have a small spot on the wall. To make it work with real optics, I had to use a short focal-length lens that somewhat disperses the light. Then it would have worked, but such lenses are very short in height. So electronics would not fit :(

It depends how to put them. If they will be located at the gaps corresponding to other side - then yes. But it is probably easier to put all LEDs at one side and resistors to other and just solder them more compact. Or remove resistors at all and use some current controllers for LEDs.

Its a 2 component epoxy from loctite :D

Thanks. Next time I will try :)

And again and again and again, haha :D

@@andrewjenery1783 Cause it spins. How do I connect wires there? Slip rings usually are designed for low RPMs

@@NickElectronics Yep you're right. I was thinking of slip ring or a battery but forgot you mentioned why those wouldn't work.

Nothing gonna happen :D

Not yet, but in the future, maybe :D

Thanks 😀

Thanks :)

@@AegisPupus Yep, I could do it. But I suppose someone has done it already :D Novelty of this video is only in wireless power transfer, and some jokes and I hope unique style

@@trumpisbackboi Relatively 😅 Depends how many are there

Hehe, Thanks ! :D

AHaha, I suppose many would be angry :D But it makes it even more funny :)

Thanks a lot :)

Join the evil side, we have cookies 🍪 😅

Yes, I was considering using EL wire, but it was just harder to use. Yes, agree with you. Definetely not safe. It has to be poured with epoxy 100%

Appreciate it :)

I think if I had to solder a lot of components close to each other now, I'd use a stencil and an oven. Do I have an oven? No :D But I'd buy one. Or make one. I'm a bit lazy and like efficiency, ahahaa :)

Rather helicopter :D

Add several more zzz's to the end of 'Bzz,' and it'll be just the right amount :D

Like a capacitive button to turn it on and off? I can do that for sure :D

I actually do not know if WPT is used in them. Is it? Could be nice to have my hands on one

Thank you! I indeed needed that for some motivation :D

For sure, but IDK if the police would allow it, though :D

Feel your pain 🥲But it will get better one day for sure! :) I am positive about it

Hahah, thanks a lot :D

Shhhhh, lets keep it secret 😁

@@NickElectronics I use it at work all the time, your secret is safe with me,

@@Rockhopper1 Ahahah, thanks :D

Thank you :)

Probably I can :D

Thanks, sure you will :D

@@anhinh2145 And no motor is necessary, cause you already pedal a bicycle and can attach the device to a spinning part 😅 Maybe just some gears, to increase spinning speed :D

Why do u need supersize one?)

She's not like that, she wouldn't say such thinkgs :)

I also just could solder diodes with some shift. But for some reason I did not think about it then. Next one will be better for sure :D

"Yes, it’s possible, of course. However, it's much harder to control because if you want at least 360 pixels of horizontal resolution, you need to refresh it 360 times per rotation. To achieve a 30 Hz refresh rate, that's 30 rotations per second, meaning the data has to be refreshed 360 * 30 times per second-around 10,800 times per second. With the same vertical resolution of 360 pixels and using RGB colors, that's 360 * 3 = 1,080 LEDs that need to be refreshed 10,800 times per second, resulting in a data rate of 11 megabits per second. And that's only for one row of LEDs. So, it’s more of a surface display with an unusual shape rather than a truly volumetric display. If I needed a truly volumetric display with a 360-pixel depth resolution, that would require controlling 360 columns, essentially 11 Mbits/sec * 360, which equals 4 Gbits/sec of data. That’s quite a lot. There may be ways to optimize it, but still, it would be challenging.

@ Thank you for this answer, it has been bugging me for a long time 😅. But if possible somehow, it would be the coolest thing ever

@@harshitprasadbulletwa In one of the next videos I will try to improve it a lot. I publish once per 2 month usually, so you have to wait a little bit 😅

You too :D