Відео

Thanks

On the real, I appreciate this video. I completed this mission on 2011 Pilot. It's clear these are meant to break, because mine didn't stand a chance. I kept using my bits in order, and eventually it cleared that entire space. Use masking tape, and BE PATIENT!! This works (August 2024)

To the Creator of this video ,I just did this for the first time for a customer , neighbor,and only,only,only because of this video ,I succeeded, U HAVE MY SUBSCRIPTION,AND IM. A 18 YEAR Self Taught MECHANIC

I just got done doing this to my 2010 Fit and it worked like a charm. Start to finish it took about 30 minutes.

Murphys Law is now Marty's Law...IF there is any chance of this damn thing breaking...it is going to break(and stay seized) Murphy has nothing on Marty ! Good Luck to every other name though.

Thank you for the tip to know how much it need drill, informative.

Just want to thank you . I view your video as I was desperate trying to remove a 17 years abs sensor on a Honda. I got some clues from your video and finally succeeded to remove the stuck mess. Thanks again.

how do you learn what sensor is bad. I been trying to figure out what my code mean. I have a 2014 Honda Accord with a code of 38-11 (ABS solenoid valve malfunction). I took it to O'reilly and that was all they could make from it. It pop on and off every other day and it driving me crazy. I brought a haynes repair book and waiting for it to come in to see if it give any more information. Also i tried taking an abs sensor out yesterday. I got the screw off and unweld the rust from it but when i pull the sensor out of the housing it wouldn't bulged. felt a lot of resistance... tried rotating but nothing. I was too scared to continue in fear of breaking it. Do you remember how to pull it out from the housing? just straight back or is there a trick.

I would’ve screw a bolt in to it and pul it out with a pliers

Just drill a small hole and put a screw there and then just pull. Don't forget to leave it soak in WD40 for a few minutes

Shop vacuum to get the drill shavings out of that sensor hole.

I didn't have much of a problem getting the old one out ,I had a problem getting the new one in and ended up breaking it trying to get it back out after it was stuck half way in

If sensors were replaced a year/year and a half ago would you think they've actually failed again(were broke during wheel bearing change) or just need cleaning?

Thanks so much .drilled it out enough to get coarse thread drywall in it then pulled out with cat paw crow bar.thanks again

hello my friend from Europe,,,please answer me a question,,,does your car have a CVT automatic transmission?,did you have problems with the transmission because of this abs sensor?.I have a honda jazz and I have problems with the abs sensor, but it is related to speed recognition, thank you.

Thanks for this. I have both frontend wheel speed units rusted in and had to bust them off. I was in the process of redoing the entire frontend anyway so I took the hubs to the bench to impact in new ball joints. I drilled out the rusted in sensors and the new ones only fit so far. I'll work the drill. Thanks again

Wouldn't it just be easier to drill a screw into the remnant of the old sensor and then lever it out?

Rear sensors broke off on my Element, I was replacing the wheel bearing and cv axles, both sides the bolt broke off flush. Odyssey, Element use very similar sensors so what you show should work with most Hondas.

The plastic shavings go inside where your axle and seal are. Would make me nervous. best to take your wheel off

DO what this guy did in the video verses ....in an accord 06 remove the upper ball joint bolt 17mm and the caliper bolts 17mm and undo the cv axel nut 32mm and push the cv axel through the knuckle and pivot the knuckle to view the plastic part down inside, which if the plastic is rusted in... it could still have to be drilled....

Worked well for me. I ended up drilling 0.8 in. deep with a 5/16" drill. Then I used an o-ring pick shaped like a hook to 'gaff' it

Do you need to change the sensor and cable or just the sensor

Was this car in the bottom of the ocean?

Great video. Thank you, sir

Thanks for the video, big help on my Mini Cooper s!!

Only one Honestly and Smart guy on UA-cam. Not need remove everythg. Great Video. Best of luck for Urself

I just did this.....I took out lower ball joint, and axle from the hub. Then from the rear of the hub you get a clear view of the magnetic strip on the bearing. THEN you can sufficiently clean out the area. I used 5/16s drill bit. Its perfect fit. You dont need to take the whole knuckle off. Just swing the knuckle back and forth after disconnecting lower ball joint. BUT you gotta take the axle out of the hub. I mean come on now. Your just leaving shards and shavings of metal and plastic if you dont. PLUS I cleaned up the magnetic strip. Its the most important part. If you just go ham on it you will ruin magnetic strip. Then youll need to replace wheel bearing. Work quick or work quick and smart.

STOP STOP! an RTX 3080 with the 150w has more hashrate than a 3070. same for the 3080ti and 3070ti. try using Nicehash OC Tune. and go with memory delta as much up as you can and you will see that you can have 80 MH/s

Don't forget to knock off all the rust from the mounting surface, I have see rust on the mounting surface hold the sensor up just enough to cause problems 😉

You have done many mistakes in using the miner at maxim memory speed and processor level. I do advice to go with the processor somewhere under 1000-750 and memory not higher than 1725 .

Have you tried trex lock core clock

I like this kid all ready

if it's a sensor and you don't need it anymore turn the can upside down spray that soccer get that thing nice and frosty than a beer a light get a drill bit and drill through that sucker and then when you drill through it and when you feel like you went through it stop and then blow out the hole and then the new sensor should fit

Finally got my raider I'm doing 68.56mh stable no BSD.... MAXED OUT MEMORY can do anything on the laptop with no issues..

I have a ROG 3070 100W(Brand New this week) I can't increase the memory over 300 since the max is +300. I'm only getting 48-49 MH/s. Is there anyway to fix it? I have tried all the online solution except flashing BIOS which I don't really want to do. Thanks!

The same thing happen to my honda accord ex 2004,3.0L.the most easier way to deal with the hustle,is to lubricate the sensor area were broke(thoroughly)then just pull the broken part with a long nose pliers,and your Done.without the drilling.😬😬😬

Sure this video is still valid? I have an Asus Rog Strix 15 with RTX 3080 16GB and just can't get it... It raise up to 66-67 MHs then drops down drastically. The temp is too high with 85-88c... The fan/power limits are blocked in the afterburner (but I see in the video that you also has it blocked/greyed!) Tried --lock-cclock 1000 and --mclock 1750 but the gpu just doesn't keep up with the values dropping down constantly... Tried gminer and trex - the same problem... Maybe this video is already outdated 'cause of the difficulty? I see 4.29 difficulty in your video and now it is 8.73 (2miners).

60mh and 54°-57° or 66mh and 63°-64° ? Which one is better ?

İ have 140w3070. with oc 67.167 mh :) (max)

Can't believe my own eyes

Thanx i copy your Numbers and now it at 66.5 to 66.90 power 128w 58c

Wait on MSI website they are saying that the GE76 Raider can run max 140w not 155w? did you manually OC?

This video was exactly what I was looking for. Thank you. I just bought the Alienware X17 with the same card. At 1150 memory OC I’m getting 61-62 Hashrate. I was too nervous to OC the memory higher since it’s in a brand new laptop but after watching this vid I’ll start easing it up. Do you have any reservations about such a high memory OC? My temps are at 61 C and so far no invalid shares but still a little weary. Thanks for the great video!

I'm digging 45 mh with a 105w RTX 3080. Do you have any suggested settings?

You overclocked your memory to max on air cooling and are mad because your laptop BSOD? Get real bruh.

hash rate same msi gp 3070 140 w

Isnt 67mh/s low? I get 65mh/s on 115w on my 3070's

How did you set the curve editior? Pls let me know

Top 30 Ethereum Twitter Accounts You Should Follow In 2021 ua-cam.com/video/_rf3RrDO4FM/v-deo.html

Wow thanks for the video I guess I will go with a 3070 with a TDP of 140.