Відео

Perfect 👌 service electric motor

You are good crafte man

ПОД КОНЕЦ,ОБОСРАЛ ВСЁ СВОИМИ ПРОВОЛКАМИ😢😢😢

А.пескоструем слабо.моешь.все.летит.на пол.как свинья

Looks like something that was placed in a muddy duck pond for 3 months and then left to rust-dry just for the sake of a sensationalistic youtube video.

Дерьмовый ремонт.один месяц эксплуатации и все.на свалку 👎

You are technisi profesional. Why you dont go to Indonesia ? To many car, if you can open this business. Wow... You can happy. That's true.

Много роботи оно етого нестоит

Генератор в отличном состоянии и требовал обычного, профессионального обслуживания....

This was a bodge job and will probably break down just after any warranty 😂 wiring not soldered or replaced and insulation tape will melt. Bearing might surprise most of us but the old brushes will be under more stress. We'll done for showing us where not to go. Restoration? Your joking😂

Pls don't repair for ur own safety

Why you don't make those booshings from bras instead using that plastic shit that won't last long.

😮😮😮😮😮😮

Piece of junk and prone to failure ! Bering's and brushes should have been replaced , Shrink wrap should have been used on the wiring and solder used on terminal not just crimped

Ésto no es restauración... Sólo intentaron lavar las piezas con petróleo. No reemplazó rodamientos y cables pelados. 🤷🏻

It was junk than and it's junk now.. Let me know when you really want to restore this to a working condition.

Mera bhi kr de

Instead of this stress why not buy a new one.

..riparazione costo 0 solo manodopera e un po' di petrolio 😂😂😂 speriamo duri 🙈🙈🙈🙈

Muy buena restauración, pero creo que el costo de materiales y mano de obra excede los precios de una pieza nueva, a menos que no se consiga la pieza sustituta.

Реклама для Ютуба, как нельзя проводить ремонт 😂

Разобрал, а теперь выброси в мусор всё 😂 это не ремонт!

May God have Mercy

Bhai apki dukan kaha he

Bhai isse kehte 👍 he hoonar Ise kehte ❤ machanic

Bodge a Job.

You are wasting people data on one thing how many people hard this machine is not simple machine

Neden kaynak yaptın zaten sıkı geçme

با گازوییلهای قاچاق از ایران تمیز میکنی ؟ 😂

I could take 5 minutes.

Para mí no es lo correcto ni las ligas cambió y a como estaba esa bomba ya debieron estar vencidas y sirven como resortes para mantener los espejos recargados a los engranes para que no se fuge el aceite y tenga buena presión

خواهرت گاییدم دوساعت الکی وقتمون گرفتی همش الکی نه بلبرینگ عوض کردی حالا اون به کنار خاهرکصت لااقل سیم که وصل کردی لحیم کن اون امپر میکشه اونم به کنار یعنی دیود سالم بود اون دیود قرمز اخریم که نذاشتی همش فک بود

Con todo el desarme que iso no cambia el rodamiento por uno nuevo mal echo

Я в начале смотрел и написал ремонт херня оказывается и подшипники повторно после сварки поставят - хотя для продажи годится

Хороший -ремонт! Молотком по валу по резьбе ударили 🤣🤣🤣🤣

Без полезное занятие, потечёт через месяц 😅

BY THE MANUFACTURERS IT IS NOT ADVISED TO TURN DISC TOTORS HOWEVER IF IT IS VEENTED BRAKE ROTRS BEFORE MACHINING CHECK THE MIN. OR DISCARD READINGS

WHEN BRAKES ARE APPLIED THERE IS LOTS OF PRESSURE BETWEEN ALL BRAKE PARTS THE PLASTIC BUSHING WILL GO BAD IN A FEW BRAKING

Osm work 😮😮😮❤❤

That's some real dirty old oil. Wow you should have just put new oil

😂

How to restore not.how to.restorstion dummy

Terrible job 😢

Looks like you are in a hell of a rush. Those parts are still dirty even though you cover them up with paint

Hope you are not going to reuse those bearings

Bad "repair". The Bearing has to be replaced. India and his experts shows your problem very well.

Why did you weld?

The best pakistani worker 😊🎉🎉🎉🎉

Stronger than the original with a great deal of personal touch qudoos to this engineer.

Проволока в конце всё испортила