Відео

Thank you very much! You helped me solve my issue.

it helped ty

ty

Got one $409 from LOWES, new, year 2k. Made in the USA and it shows...motor runs good but slapped on seals and assembly. Now looking for front valve cover seal and noticed oil weeping in same location as yours. Ist one went back to Lowes due to faulty under deck construction..small twigs get jammed under plastic to metal under deck, bulging plastic down till the blade strikes. We all got that issue that is just piss poor engineering. Somebody posted that flaw here on YTube. If the layer laps were reversed.. then NO problem. Has not done that on second mower..yet. Got 11 year old Chondas with no issues!

How do I know if my pulleys are good?

Thank you thank you, exactly what I needed!

Would this also apply for a Lowe’s 5x8 trailer?

42 "?

42"

How bout dummy flips for tractors?

Hi, need a Carburetor for a 20yr old Briggs and stratton 15.5 IC OHV Craftsman RIDING MOWER.... Could you tell me which one fits?I would greatly appreciate it.....THANKS!

THANK YOU that spring has been making me crazy on how it gos. great video.

Stevie Wonder must be doing quality control for Honda.

180 dollars at the dealer,,,,

Great video. Thanks.

Very informative, thank you

Thank you so much!

I have a 2460 magnum.my batt wire from ignition to regulator always has 12.56 volts.even with key off.is my key ignition bad?when running that wire has 14.9v

I have one that sometimes has to be put I forward gear then reverse for it to back up. I put new belt on it. Did not solve the problem. Sometimes a little jerky in forward too. Maybe I need to relocate spring just a little? I think the Holly’s are good. None broken like that one anyway. Bought the belt from a small engine parts shop/store. Maybe not oem, not sure.

I bought a KIPA carb off Amazon for my B&S 14.5hp rider for $20...been running great for the last 2 years.

Terrible video

Mine has the exact same problem!

Very hard to find any videos or pictures on this rare mower. Great job. Thank you!

Very well done. When I got the tractor from a friend with a new card to install the choke arm was just dangling and I could not figure out where it went this was a huge help.

Gracias

I welded my bolt to a plate so I could get 2 c clamps on either side. but she worked.

Got a used Ariens (same model) for $75 all that was missing was one part from the throttle linkage. Thank you for saving me from hours of confusion!

This video was so good and it helped me with exactly what I’m working on. Thank you.

I have a Dixie with no click no start. Pull the PTO up and down 15-20 times, it may start. Feel like that’s the issue. Is it easy to replace?

What size wire did you run from your solenoid to the starter? Also what size wire to you recommend for wiring rest?

What if you have a ground going to the ignition coil? Thanks

Thank you very much

Thank you, so much for this info, I was going to junk my trimmer, thank you again,

A good bite.

Thank you thank you. I did not expect that choke rod to just float

You have to stretch the pool from the inside like a lot of people have been doing in their videos in UA-cam.

Good video, but those wrinkles in the bottom of the liner that touches the ground HAVE to be smoothed out while you're starting to fill it. If not that's where you will get your first leak. You need to work out the wrinkles from the inside and out while there's about an inch of water. You can't get the wrinkles out after it has too much water weight in it.

Wouldn't happen to know where the ground wire from ignition sensor grounds to the unit

Thanks for the instructions, wish I could find a cover for it.

Thank You. Exactly the explanation I needed to get the job done.

A deal

my Briggs and Stratton vtwin engine is revving to high. Will the governor arm not lift the throttle back to idle unless the engine is running? Thank you for your help.

It will run but I have to manually move the linkages... Not sure what I'm doing wrong

I'm having the same problem I took mine apart to clean the carb and the little bent wire that comes up and chokes it when you push the throttle lever all the way to choke isn't returning once I move the throttle back to the run position... It's all hooked up just like this one on here. I'm wondering if I have a return spring that's worn out there's not a lot of tension on it....

I bought this pool from Walmart for $78 yesterday. And now I'm watching this video to learn how to set it up.

Good looking mower and deck really good 😊😊😊 It’s going to make a good sale 😊

Where can I find that instruction sheet? My Toro manual doesn’t even cover trans maintenance. Thx!

would like you to do a video on changing the drive oil and filters in a zee 2 good to know about the fuse

I don’t know.. that’s why I’m watching the video

Thanks for the help